Rational Design of 3D Honeycomb-Like SnS2 Quantum Dots/rGO Composites as High-Performance Anode Materials for Lithium/Sodium-Ion Batteries
Structure pulverization and poor electrical conductivity of metal dichalcogenides result in serious capacity decay both in lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs). To resolve the above problems, a combination of metal dichalcogenides with conductive scaffolds as high-performance electrode materials has aroused tremendous interest recently. Herein, we synthesize a 3D honeycomb-like rGO anchored with SnS2 quantum dots (3D SnS2 QDs/rGO) composite via spray-drying and sulfidation. The unique 3D-ordered honeycomb-like structure can confine the volume change of SnS2 QDs in the lithiation/delithiation and sodiation/desodiation processes, provide enough space for electrolyte reservoirs, promote the conductivity of the SnS2 QDs, and improve the electron transfer. As a result, the 3D SnS2 QDs/rGO composite electrode delivers a high capacity and long cycling stability (862 mAh/g for LIB at 0.1 A/g after 200 cycles, 233 mAh/g for SIB at 0.5 A/g after 200 cycles). This study provides a feasible synthesis route for preparing 3D-ordered porous networks in varied materials for the development of high-performance LIBs and SIBs in future.
KeywordsSnS2 quantum dots Spray drying rGO Lithium-ion batteries Sodium-ion batteries
- 3D SnS2 QDs/rGO
3D Honeycomb-like SnS2 Quantum Dots/rGO
Solid electrolyte interface
Field emission scanning electron microscope
Transmission electron microscope
X-ray photoelectron spectroscopy
Energy storage plays a remarkable role in modern life. Li-ion batteries (LIBs) have been widely applied as a power source for portable electronic devices and power electric vehicles due to their long cycle life stability and high energy density. Meanwhile, Na-ion batteries (SIBs) have attracted tremendous attention in renewable energy storage because of their low cost and environmental benignity. While the commercial graphite anodes of LIBs show low theoretical capacity (372 mAh/g) and suffer from structural instability and safety problem during a high-rate charge-discharge process, also cannot be used in SIBs owing to their small inter-layer space [1, 2, 3, 4]. Therefore, novel anode materials with high capacity need to be developed for the next-generation LIBs and SIBs.
Metal dichalcogenides, possessing high theoretical capacities, are promising candidates for replacing the commercial graphite in LIB and SIB applications. Among the metal dichalcogenides, layered SnS2 exhibits a higher theoretical capacity than graphite, and has been regarded as an attractive anode material. SnS2 is a typical CdI2-type, where the each layer connects with each other mainly by weak Van der Waals force. Such a feature makes it a desired intercalation/deintercalation candidate for Li+ and Na+ in the first step of the conversion reaction. However, SnS2 suffers from large volume change and poor electrical conductivity in the charge-discharge process, thus results in severe capacity decay.
Integrating SnS2 with other conductive scaffolds to design a rational structure especially a three-dimensional (3D)-ordered porous network has been considered as feasible strategies to improve the electrical conductivity and cycling stability of LIBs and SIBs [5, 6]. Graphene is considered a promising candidate for scaffolds owing to its excellent mechanical characteristics and electronic conductivity. Firstly, compared to 1D and 2D structures, a 3D-ordered porous network is more conducive to the complete contact between the electrode and electrolyte. Thus, it can act as a channel for fast electron transport along the 3D direction and restrain the aggregation effectively . Secondly, the rich pores in 3D-ordered porous network can relieve the volume expansion in three dimensions space and thus makes it exhibit long cycle life stability [8, 9, 10, 11, 12, 13, 14]. Zhu et al. designed Co3O4 with a 3D mesoporous network and showed excellent performance in LIBs . Deng et al. demonstrated a new 3D-ordered macroporous MoS2/carbon nanostructure is beneficial for obtaining high-performance of LIBs . Choi et al. synthesized layered WS2 nanosheet-decorated 3D-RGO microspheres as an anode material for SIBs . Based on the above discussion, we have designed a unique 3D honeycomb-like structure to buffer the large volume change and enhance the electrical conductivity of SnS2 by spray drying and sulfidation. The composite achieves excellent electrochemical performance in both LIBs and SIBs (862 mAh/g for LIB at 0.1 A/g after 200 cycles, 233 mAh/g for SIB at 0.5 A/g after 200 cycles).
The 3D-structured honeycomb-like rGO anchored with SnS2 quantum dots composite (3D SnS2 QDs/rGO) via a two-step method. Firstly, the 3D honeycomb-like rGO anchored with SnO2 composite (3D SnO2/rGO) is synthesized through spray drying and post-calcination. Then, it is annealed with thiourea to obtain the 3D SnS2 QDs/rGO composite under the argon atmosphere. The 3D honeycomb-like structure can reduce the inter-sheet junction contact resistance effectively, provide a large accessible active surface area for the adsorption/desorption of ions, restrain the aggregation of SnS2 QDs, and buffer the volume expansion of SnS2 QDs [18, 19, 20]. As a result, the SnS2 QDs with a diameter of ~ 6 nm are uniformly distributed within the rGO layer after 200 charge/discharge cycles in the LIB test. Moreover, the 3D SnS2 QDs/rGO composite electrode possesses a high capacity and long cycling stability (862 mAh/g for LIB at 0.1 A/g after 200 cycles, 233 mAh/g for SIB at 0.5 A/g after 200 cycles). The unique metal sulfide-based 3D porous graphene materials presented in this study provide a way to the development of high-performance LIBs and SIBs.
Synthesis of Polystyrene Nanospheres
All reagents used were of analytical grade and were used directly without any purification. Styrene was alternatively washed with DI water and 1 M NaOH to remove the polymer inhibitors. Then, 8 ml styrene, 92 ml DI water, and 0.2 g K2S2O8 were mixed and then stirred at 80 °C for 10 h in argon atmosphere. Finally, a white product was obtained by centrifugation. After washed by DI water and ethanol for at least five times, the product was freeze-dried at − 50 °C for 24 h .
Fabrication of 3D SnS2 QDs/rGO Composite
In a typical synthesis, 24 g graphene oxide (GO) colloidal (2.5 wt%) that was obtained by the modified Hummer approach was added into 500 ml DI water. Then, 3 g polystyrene (PS) nanospheres were dispersed in the prior solution [21, 22]. Further, 1.5 g tin (IV) chloride pentahydrate (SnCl4.5H2O) was placed into the mixture and ultra-sonication for 1 h. The mixture solution was spray-dried with exit temperature of 140 °C and a flow rate of 800 ml/h. Subsequently, the collected product was annealed at 450 °C for 2 h at a ramping rate of 3 °C min−1 in Ar atmosphere to remove PS nanospheres, and then the 3D SnO2/rGO was obtained. Finally, thiourea, acting as the sulfur source, was mixed with the SnO2/rGO. And then it was annealed at 350 °C for 12 h at a heating rate of 2 °C min−1 in Ar atmosphere to ensure the 3D SnO2/rGO composite completely transformed into 3D SnS2 QDs/rGO composite . The pure SnS2 composite was synthesized in the absence of GO and PS nanospheres.
The crystalline structure and phase of the composites were tested by X-ray diffraction (XRD, D8-Advance Bruker) with Cu-Kα (λ = 1.5418 Å) radiation at 40 kV and 40 mA, ranging from 10 to 80 °C at room temperature. The surface chemical composition of the composites was analyzed by a modified X-ray photoelectron spectroscopy (XPS, PHI 5600). The morphologies and structures were examined by field emission scanning electron microscope (FESEM, JEOL S-4800) and transmission electron microscope (TEM, JEOL JEM-2010). The Brunauer–Emmett–Teller (BET) surface area and pore size were identified by using the nitrogen adsorption/desorption isotherms obtained at 77 K on a surface area and porosity analyzer (Quadrasorb SI-MP, Quantachrome). The Raman spectrum was obtained by an INVIA Raman microprobe (Renishaw Instruments) with a 532 nm laser source and a × 50 objective lens. The thermogravimetric analyzer (TGA) curve was performed using an STD Q600 TA with 100 ml min−1 of air flow from 30 to 800 °C at a heating rate of 10 °C min−1.
To prepared working electrodes, 70 wt% 3D SnS2 QDs/rGO composite, 20 wt% acetylene black, and 10 wt% polyvinylidene fluoride were mixed and dissolved in N-methyl-2-pyrrolidinone. After stirring for 5 h, the obtained slurry was coated onto the copper foil (acted as a current collector) and dried at 80 °C in vacuum overnight. The electrochemical tests were carried out using two-electrode cells assembled in an argon-filled glove box. Li and Na metals acted as the counter electrode. The organic electrolyte in LIBs was constituted of 1.0 M LiPF6 in ethylene carbonate (EC) and diethyl carbonate (DEC) (1:1, v/v). For SIBs, the electrolyte was 1 M NaClO4 in a mixture of EC/DEC (1:1, v/v). Galvanostatic charge/discharge measurements were performed by a battery test system (NEWARE, Shenzhen Xinwei Electronics, Ltd) at different current densities with a voltage range of 0.01–3.00 V. Cyclic voltammetry (CV) and the cyclic voltammograms were recorded over the potential range of 0.01–3.00 V with a scan rate of 0.1 mV/s.
Results and Discussion
The surface chemical composition and oxidation state of the composite are analyzed by XPS system. In Fig. 2d, the two prominent peaks at 487.3 and 495.7 eV are ascribed to Sn 3d3/2 and Sn 3d5/2, respectively. The energy difference between Sn 3d5/2 and Sn 3d3/2 is 8.4 eV, which indicates the Sn4+ oxidation state . The survey XPS S 2p spectrum is presented in Fig. 2e. The characteristic peaks appearing at 161.3 and 163.4 eV are attributed to S 2p3/2 and S 2p1/2 for S2− in SnS2 [27, 31]. The XPS spectrum of C 1s showed in Fig. 2f can be fitted and split into three different peaks of 284.7, 285.7, and 288.1 eV, respectively. The three peaks belonged to the C-C, C-O, and C=O bonds, respectively [25, 32].
The mass percentage of SnS2 in 3D SnS2 QDs/rGO composite was conducted by TGA from 30 to 800 °C at a heating rate of 10 °C/min in air. In Additional file 1: Figure S4a, the 3D SnS2 QDs/rGO composite was completely oxidized to SnO2 over 800 °C, producing a total weight loss of about 29.5%. The process of weight loss contained three processes, namely the desorption of water molecules (1.4%) adsorbed on the 3D SnS2 QDs/rGO composite, oxidization of SnS2, and the successively burning of rGO. The weight percentages of SnS2 in the 3D SnS2 QDs/rGO composite can be calculated to be 83.7%, based on the complete weight loss of rGO combustion and the partial weight loss from the transformation of SnS2 into SnO2 .
Note that the intensities of the reduction peaks of SnS2 decrease drastically in the second and fifth scans. In contrast, the reduction peaks of the 3D SnS2 QDs/rGO electrode perfectly overlap in the second and fifth scans, suggesting its excellent electrochemical reversibility and stability.
Galvanostatic charge/discharge measurements of the pure SnS2 and 3D SnS2 QDs/rGO electrodes are also performed at a current density of 0.1 A/g between 0.01 and 3.00 V vs Li+/Li. The charge/discharge curves (1st, 2nd, 50th, and 200th cycles) are shown in Fig. 3c, d, respectively. In Fig. 3c, the charge/discharge curve of the pure SnS2 electrode shows a drastic decrease to 16 mAh/g after the 200th cycle. In Fig. 3d, the initial discharge capacity for the 3D SnS2 QDs/rGO electrode is 1400 mAh/g. It is higher than the theoretical storage capacity of Li+ (1231 mAh/g) of SnS2 calculated from both reactions (1) and (2) according to the Faraday equation. This is ascribed to the formation of a SEI layer on the surface of the 3D SnS2 QDs/rGO electrode caused by the irreversible insertion of Li+ and the decomposition of the electrolyte . Upon increasing the cycles to 2, 50, and 200, the capacities of the 3D SnS2 QDs/rGO electrode are maintained at 975, 867, and 870 mAh/g, respectively. Obviously, the 3D SnS2 QDs/rGO electrode possesses an excellent charge/discharge stability and long cycle life than the pure SnS2 electrode.
The rate performances of the electrodes are presented in Fig. 3e. It can be seen that the discharge capacity at a rate of 0.1, 0.2, 0.5, and 1 A/g is 870, 770, 622, and 452 mAh/g, respectively. Then it easily return to 867 mAh/g at 0.1 A/g, indicating that the 3D SnS2 QDs/rGO composite can bear gradual rate variations and possesses remarkable electrochemical stability and reversibility. While the pure SnS2 electrode’ capacity decays to 792, 587, 319, and 106 mAh/g with the discharge/charge rates increased to 0.1, 0.2, 0.5, and 1 A/g, respectively. And it only restores to 662 mAh/g when the discharge/charge rate is recovered to 0.1 A/g. The outstanding electrochemical performance of 3D SnS2 QDs/rGO composite electrodes is further presented in Fig. 3g. The capacity of the pure SnS2 electrode drastically decreases to almost 16 mA/g after 200 cycles, while the 3D SnS2 QDs/rGO electrode can still maintain a value of 870 mAh/g after 200 cycles at a current density of 0.1 A/g. Moreover, in Fig. 3h, the test is performed to prove the better cycling performance of the composite at a scan rate of 0.5 A/g. After 200 charge/discharge cycles, a high reversible capacity of 622 mAh/g remained and the average Coulombic efficiency is as high as 99.44%.
To further understand the better cycle life of the 3D SnS2 QDs/rGO electrode, a TEM image is acquired to prove the distribution of the SnS2 QDs (in Additional file 1: Figure S3, by measuring 100 representative particles using the Nano-Measure software). The SnS2 QDs with ~ 6 nm are almost evenly anchored and limited within the rGO layers, indicating a strong adsorption between SnS2 QDs and the rGO layers. Overall, the results of both the electrochemical test and the particle distribution demonstrate that the introduction of rGO and the 3D honeycomb-like network offers abundant void spaces for volume expansion of SnS2 QDs. These structures act as channels for fast transportation of electron along all three directions and effectively restrain the aggregation. Thus, the rate performance and cycling stability of the composite are enhanced. Figure 3f shows a comparison of the electrochemical performance between the 3D SnS2 QDs/rGO composite (the current study) and the previously reported SnS2-based materials composite. It can be observed that the capacity of 3D SnS2 QDs/rGO in our study remains 862 mAh/g LIB at 0.1 A/g after 200 cycles, which is higher than the other rGO and SnS2-based material, such as graphene-SnS2 hybrids , acetylene black-SnS2 , SnS2@reduced graphene oxide , mesoporous carbon anchored with SnS2 nanosheets , graphene-SnS2 , SnS2 nanoparticle-loaded grapheme , SnS2@graphene , and Ultrathin SnS2 nanoparticles on graphene nanosheets .
In reverse scanning, the unconspicuous oxidation peaks at 0.35, 1.2, and 2.25 V are ascribed to the desodiation of NaxSn. The obvious oxidation peak at 1.2 V belongs to the resilience of the initial 3D SnS2 QDs/rGO electrode . Note that the subsequent CV scans of 3D SnS2 QDs/rGO overlap well after the first cycle, indicating good reversibility of it for the sodiation and desodiation reactions.
The discharge-charge voltage profiles of the pure SnS2 and 3D SnS2 QDs/rGO electrodes are carried out between 0.01 and 3 V at a current density of 0.1 A/g. The corresponding charge/discharge profiles (1st, 2nd, and 5th cycles) are shown in Fig. 4c, d, respectively, which are in accord with the CV results. In Fig. 4c, a remarkable plateau appears at ~ 1.0 V in the discharge process, belonging to the formation of NaxSnS2. The plateau at 0.5–1.0 V is attributed to the conversion, while that below 0.5 V is assigned to the alloying reactions between Na+ and Sn. Then, the CV curve of the 3D SnS2 QDs/rGO electrode (Fig. 4d) indicates that the inconspicuous plateau voltage at ~ 1.0 V is assigned to the intercalation of Na+ into SnS2 layers during the first discharge process and this reaction is expressed as Eq. (3). The slope plateau at 0.3–1.0 V corresponds to the conversion reaction (Eq. (4)), the formation of the SEI layer by the irreversible insertion of Na+, and the decomposition of the electrolyte. The plateau below 0.3 V corresponds to the alloying reaction (Eq. (5)) [48, 49, 50]. The electrode shows a plateau at ~ 1.0 V and a slope plateau at ~ 1.6 V in the charge process, which are also in agreement with the CV results.
The rate capability of the pure SnS2 and 3D SnS2 QDs/rGO electrodes from 0.1 to 5 A/g in the SIB test are given in Fig. 4e. The 3D SnS2 QDs/rGO electrode is remarkably superior by comparison. It can be seen that the discharge capacities at the rate of 0.1, 0.5, 1, and 5 A/g are 397, 286, 213, and 95 mAh/g, respectively, and then easily return to 393 mAh/g at 0.1 A/g. But for the pure SnS2 electrode, the discharge capacity decays to 180, 59, 25, and 11 mAh/g with the discharge rate increased to 0.1, 0.5, 1, and 5 A/g, respectively. Then the discharge capacity only restores to 102 mAh/g when the discharge rate recovers to 0.1 A/g. The 3D SnS2 QDs/rGO electrode shows slight changes in discharge capacity after discharge at different current densities, which indicates better resilience of the nanostructure. Obviously, the unique 3D honeycomb-like structure allows Na+ transport at high current density without creating many irreversible changes of the electrode’s nanostructure, resulting in an excellent performance in SIBs. The discharge capacity of the pure SnS2 electrode retains only 6 mAh/g after 200 cycles at a scan rate of 0.5 A/g, which is significantly lower than that 233 mAh/g in the 3D SnS2 QDs/rGO electrode, as presented in Fig. 4f. A serious capacity decay of the pure SnS2 electrode can result from the low electronic conductivity of the unsupported SnS2 and the uncontrollable aggregations of Sn (or its discharge products) during the cycling. Thus, the outstanding electrochemical performance of the electrode corresponds to the 3D honeycomb-like structure. The existing porous in the structure can efficiently adjust the volume change in the process of alloying and de-alloying.
To better understand the charge storage process, the CV curves at various scan rates (0.1–1 mV/s) are performed to understand the electrochemical process (Fig. 4g). A peak shift appears with the scanning rate rising from 0.1 to 1 mV/s, indicating the polarization of the electrode. The capacity contribution from capacitive and diffusion-controlled charge can be quantified according to the relation  i (V) = k1v + k2v1/2, where k1v and k2v1/2 are the contributions from the capacitive and diffusion-controlled processes, respectively. From Fig. 4h, it can be observed that the capacitance-controlled capacity accounts for 76.1% of the total charge storage at a scan rate of 1 mV/s. With the scan rate increases in the order of 0.1, 0.3, 0.6, 0.7, and 1 mV/s, the proportion of the capacitance-controlled process increases from 67.4, 70.3, 73.2, 75.7, to 76.1%, respectively (Fig. 4i). The result indicates that the capacitive charge storage plays an important role in the total capacity of the electrode . However, the relative rapid capacity decreases at higher scan rate is attributed to the diffusion-limited electrochemical energy conversion process .
A novel 3D honeycomb-like SnS2 QDs/rGO composite was synthesized by one-pot spray drying and sulfidation. The SnS2 QDs (~ 6 nm) was uniformly distributed in the rGO layers. The thicknesses of the rGO sheets could be regulated by changing the concentration of GO in the spray solution. What is more, the size of the rGO nanovoids could be easily adjusted by using different size of the PS nanospheres. The 3D honeycomb-like rGO could not only buffer the volume expansion of the SnS2 QDs but also enhance their poor electrical conductivity. In addition, it can provide enough space for electrolyte reservoirs. As a result, the retention of the reversible capacity of the 3D SnS2 QDs/rGO electrode for LIB at 0.1 A/g was nearly 862 mAh/g and the capacity was as high as 622 mAh/g after 200 cycles at 0.5 A/g. Moreover, a capacity of 233 mAh/g could be delivered after 200 cycles at 0.5 A/g in the SIB test. The novel 3D honeycomb-like SnS2 QDs/rGO composite suggested a new strategy for preparing anode material in LIBs and SIBs. This advanced anode materials is predicable to have a significant influence on the energy storage field, and thus, provide fresh opportunities to enhance the electrochemical performance of Li+ and Na+ storage devices.
The authors gratefully acknowledge the financial support given for this work by the National Natural Science Foundation of China, the Innovative Research Team (in Science and Technology) in University of Henan Province, and the program for Science & Technology Innovation Talents in Universities of Henan Province.
This work was financially supported by the National Natural Science Foundation of China (Nos. 51502257, 61574122, 21373107 and 61704146), the Innovative Research Team (in Science and Technology) in University of Henan Province (No. 13IRTSTHN018), and the program for Science & Technology Innovation Talents in Universities of Henan Province (No. 15HASTIT018).
Availability of Data and Materials
All data and materials are fully available without restriction.
YG (Zhang) prepared the manuscript, YG and YG (Wang) carried out the experiment. TP, YL, RJ, and YB helped in the technical support for the characterizations. YS, XM, and JK designed the experiment. All the authors discussed the results and approved the final manuscript.
The authors declare that they have no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
- 16.Deng Z, Jiang H, Hu Y, Liu Y, Zhang L, Liu H, Li C (2017) 3D ordered macroporous MoS2@C nanostructure for flexible li-ion batteries. Adv. Mater 29:1603020Google Scholar
- 25.Yu Z, Li X, Yan B, Xiong D, Yang M, Li D (2017) Rational design of flower-like tin sulfide @ reduced graphene oxide for high performance sodium ion batteries. Mater. Res. ES Bull 96:516–523Google Scholar
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.