Abstract—
Tempered glass is a transparent material that can withstand various shocks and constant loads, which is widely used in the field of safety protection. This manuscript presents the determination of Johnson–Holmquist (JH-2) model parameters for tempered glass and investigates the effect of strain rate on its strength through quasi-static and dynamic compression tests. The hydrostatic tensile pressure was indirectly determined via split tensile tests, and literature data were employed to calculate the value of HEL and EOS. The JH-2 model accurately predicted the real shapes of strain waves in the input and output bar of SHPB tests and was capable of describing the mechanical behavior of the brittle material from elasticity to fracture. The determined parameters for tempered glass were validated to represent the response to shock and impact loads.
Similar content being viewed by others
REFERENCES
Balan, B.A. and Achintha, M., Assessment of stresses in float and tempered glass using eigenstrains, Exp. Mech., 2015, vol. 55, no. 7, pp. 1301–1315.
Bernard, F., Gy, R., and Daudeville, L., Finite element computation of residual stresses near holes in tempered glass plates, in Proceedings of the 19th International Congress on Glass, 2001, pp. 290–295.
To, Q.-D., He, Q.-C., and Cossavella, M., The tempering of glass and the failure of tempered glass plates with pin-loaded joints: Modelling and simulation, Mater. Des., 2008, vol. 29, no. 5, pp. 943–951.
Zhou, H., Xi, G., and Li, D., Modeling and simulation of residual stresses during glass bulb pressing process, Technol. Sci., 2007, vol. 50, no. 1, pp. 103–117.
Nielsen, J.H., Olesen, J.F., and Poulsen, P.N., Simulation of residual stresses at holes in tempered glass: A parametric study, Mater. Struct., 2010, vol. 43, no. 7, pp. 947–961.
Kim, J.H., Kong, J., and Chung, K., Analysis of annealing processes of glass sheets based on structural relaxation model, Int. J. Mech. Sci., 2013, vol. 66, p. 249–259.
Béchet, F., Siedow, N., and Lochegnies, D., Two-dimensional finite element modeling of glass forming and tempering processes, including radiative effects, Finite Elem. Anal. Des., 2015, vol. 94, pp. 16–23.
Ma, Y., Wu, N., and Zhang, H., Thermal annealing system and process design to improve quality of large size glasses, Int. J. Heat Mass Transfer, 2014, vol. 72, pp. 411–422.
Biolzi, L., Cattaneo, S., and Rosati, G., Progressive damage and fracture of laminated glass beams, Construct. Build. Mater., 2010, vol. 24, no. 4, pp. 577–584.
Du Bois, P.A., Kolling, S., and Fassnacht, W., Modelling of safety glass for crash simulation, Comput. Mater. Sci., 2003, vol. 28, nos. 3–4, pp. 675–683.
Holmquist, T.J., Johnson, G.R., and Lopatin, C.M., High strain rate properties and constitutive modeling of glass online, Paper SAND-95-0379C, CONF-950537-2, Albuquerque, NM: Sandia Natl. Lab., 1995.
Wu, C.D., Yan, X.Q., and Shen, L.M., A numerical study on dynamic failure of nanomaterial enhanced laminated glass under impact, IOP Conf. Ser.: Mater. Sci. Eng., 2010, vol. 10, p. 012176.
Grujicic, M., Bell, W.C., and Pandurangan, B., The effect of high-pressure densification on ballistic-penetration resistance of a soda-lime glass, Proc. Inst. Mech. Eng., Part L: J. Mater.: Des. Appl., 2011, vol. 225, no. 4, pp. 298–315.
Anderson, C.E., Jr. and Holmquist, T.J., Application of a computational glass model to compute propagation of failure from ballistic impact of borosilicate glass targets, Int. J. Impact Eng., 2013, vol. 56, pp. 2–11.
Nam, J., Kim, T., and Cho, S.W., A numerical cutting model for brittle materials using smooth particle hydrodynamics, Int. J. Adv. Manuf. Technol., 2016, vol. 82, nos. 1–4, pp. 133–141.
Zhang, X., Hao, H., and Ma, G., Dynamic material model of annealed soda-lime glass, Int. J. Impact Eng., 2015, vol. 77, pp. 108–119.
Anderson, C.E., Jr., Ballistic experiment and computations of confined 99.5% Al2O3 ceramic tiles, in Proceedings of the 15th International Symposium on Ballistics, 1995.
Holmquist, T.J., Templeton, D.W., and Bishnoi, K.D., Constitutive modeling of aluminum nitride for large strain, high-strain rate, and high-pressure applications, Int. J. Impact Eng., 2001, vol. 25, no. 3, pp. 211–231.
Holmquist, T.J. and Johnson, G.R., Characterization and evaluation of silicon carbide for high-velocity and impact, J. Appl. Phys., 2005, vol. 97, no. 9, p. 093502.
Claesson, J. and Bohloli, B., Brazilian test: Stress field and tensile strength of anisotropic rocks using an analytical solution, Int. J. Rock Mech. Mining Sci., 2002, vol. 39, no. 8, pp. 991–1004.
Li, D. and Wong, L.N.Y., The brazilian disc test for rock mechanics applications: Review and new insights, Rock Mech. Rock Eng., 2013, vol. 46, no. 2, pp. 269–287.
Rocco, C., Guinea, G.V., and Planas, J., Size effect and boundary conditions in the brazilian test: Experimental verification, Mater. Struct., 1999, vol. 32, no. 3, pp. 210–217.
Gama, B.A., Lopatnikov, S.L., and Gillespie, J.W., Jr., Hopkinson bar experimental technique: A critical review, Appl. Mech. Rev., 2004, vol. 57, no. 4, pp. 223–250.
Alexander, C.S., Chhabildas, L.C., and Reinhart, W.D., Changes to the shock response of fused quartz due to glass modification, Int. J. Impact Eng., 2008, vol. 35, no. 12, pp. 1376–1385.
Alexander, C.S., Chhabildas, L.C., and Templeton, D.W., The Hugoniot elastic limit of soda-lime glass, AIP Conf. Proc., 2007, vol. 955, p. 733–738.
Marsh, S.P., Lasl Shock Hugoniot Data, California: Univ. California Press, 1980.
Rosenberg, Z., Yaziv, D., and Bless, S., Spall strength of shock-loaded and glass, J. Appl. Phys., 1985, vol. 58, no. 8, pp. 3249–3251.
Grady, D.E. and Chhabildas, L.C., Shock-Wave Properties of Soda-Lime Glass, Albuquerque, NM: Sandia Natl. Labs., 1996.
Bourne, N.K. and Rosenberg, Z., The ramping of shock waves in three glasses, Proc. R. Soc. London, Ser. A, 1996, vol. 452, no. 1949, pp. 1491–1496.
Dandekar, D.P., Index of refraction and mechanical behavior of soda lime glass under shock and release wave and propagations, J. Appl. Phys., 1998, vol. 84, no. 12, pp. 6614–6622.
Wenqi, H., Yuan, C., and Zhiang, H., General specifications of forced entry resistant glass, GA Paper No. 844-2009, 2009.
Walley, S.M. and Field, J.E., Strain rate sensitivity of polymers in compression from low to high rates, DYMAT J., 1994, vol. 1, no. 3, pp. 211–227.
Toqueboeuf, W., Mortaigne, B., and Cottenot, C., Dynamic behaviour of polycarbonate/polyurethane multi-layer for transparent and armor, J. Phys. IV, 1997, vol. 7, no. C3, p. 499.
Funding
This work was supported by the Key Program for International Scientific and Technological Cooperation Projects of China (project no. 2014DFB50100) and the National Natural Science Foundation of China (project no. 11702031).
Author information
Authors and Affiliations
Contributions
Wenyu CHENG: Conceptualization, Methodology, Software, Formal analysis, Investigation, Writing – original draft. Xiaomian HU: Validation, Investigation, Writing – review & editing, Supervision, Project administration, Funding acquisition. Hao PAN: Validation, Investigation, Writing – review & editing, Supervision.
Corresponding author
Ethics declarations
The authors declare that they have no conflicts of interest.
Rights and permissions
About this article
Cite this article
Wenyu Cheng, Hu, X. & Pan, H. Johnson–Holmquist Model Parameter Determination for Tempered Glass under Impact Loading. Glass Phys Chem 49, 340–353 (2023). https://doi.org/10.1134/S1087659622600193
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S1087659622600193