Abstract
The recommendations are given for conical pick patterns to prevent growing forces on neighbor picks of a failed pick. It is proposed to detect promptly pick failures by analyzing the burden variation in the transmission system of the cutting head. According to the theoretical calculations, when a pick fails, the relative growth of the feed force is not higher than the relative growth of the cutting force as against the increase in the burden as a consequence of change in the cut rock strength. This hypothesis was tested and proved during shafting at Talitsky site of the Upper Kama Potash–Magnesium Ore Deposit using shaft cutting machine 1SPKV-8.0.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
Prokopenko, S.A., Ludzish, V.S., and Kurzina, I.A., Improvement of Cutting Tools to Enhance Performance of Heading Machines in Rocks, Journal of Mining Science, 2016, vol. 52, no. 1, pp. 153–159.
Krestovozdvizhensky, P.D., Klishin, V.I., Nikitenko, S.M., and Gerike, P.B., Selecting Shape of Reinforcement Insertions for Tangential Swivel Cutters of Mining Machines, Journal of Mining Science, 2015, vol. 51, pp. 323–329.
Mattis, A.R., Labutin, V.N., and Cheskidov, V.I., Active Rotor for a Surface Miner, Journal of Mining Science, 2008, vol. 44, no. 2, pp. 198–205.
Dewangan, S. and Chattopadhyaya, S., Performance Analysis of Two Different Conical Picks Used in Linear Cutting Operation of Coal, Arabian J. Sci. Eng., 2016, vol. 41, no. 1, pp. 249–265.
Linnik, Yu.N., Zhabin, A.B., Linnik, V.Yu., and Polyakov, A.V., Evaluation of the Effect of Pick and Holder Failure on Performance Parameters of Coal Mining Machines, Izv. TulGU. Nauki o Zemle, 2018, no. 2, pp. 247–263.
Talerov, M.P. and Bolobov, V.I., Durability and Failure Types of Conical Picks, Gornyi Zhurnal, 2018, no. 4, pp. 77–81.
Klishin, V.I., Gerike, B.L., Nikitenko, S.M., and Krestovozdvizhensky, P.D., Types and Causes of Conical Pick Failures, Gornyi Zhurnal, 2016, no. 7, pp. 92–95.
Dewangan, S. and Chattopadhyaya, S., Characterization of Wear Mechanisms in Distorted Conical Picks after Coal Cutting, Rock Mech. Rock Eng., 2016, vol. 49, no. 1, pp. 225–242.
Krauze, K., Skowronek, T., and Mucha, K., Influence of the Hard-Faced Layer Welded on Tangential-Rotary Pick Operational Part on to its Wear Rate, Arch. Min. Sci., 2016, vol. 61, no. 4, pp. 779–792.
Yang, D., Jianping, L., Zheng, K., and Jiang, H., High-Hardness Alloy Substituted by Low Hardness during Drilling and Cutting Experiments of Conical Pick, Int. J. Rock Mech. Min. Sci., 2017, no. 95, pp. 73–78.
Klishin V.I., Nikitenko S.M., Gerike B.L., and Krestovozdvizhensky, P.D., New Reinforcing Inserts for Conical Picks, Gornyi Zhurnal, 2014, no. 12, pp. 89–92.
Liu, S., Ji, H., Liu, X., and Jiang, H., Experimental Research on Wear of Conical Pick Interacting with Coal-Rock, Eng. Failure Analysis, 2017, vol. 74, pp. 172–187.
Yang, D., Li, J., Wang, L., Kuidong, G., Tang, Y., and Wang, Y., Experimental and Theoretical Design for Decreasing Wear in Conical Picks in Rotation-Drilling Cutting Process, Int. J. Advanced Manufacturing Techn., 2015, vol. 77, nos. 9–12, pp. 1571–1579.
Zhabin, A.B., Polyakov, A.V., and Averin, E.A., On the Necessity to Introduce a State Standard for Determining the Abrasiveness of Rocks, Ugol’, 2018, no. 11, pp. 86–91.
Talerov, M.P., Bolobov, V.I., and Chupin, S.A., Procedure for Calculating Durability and Determining the Cause of Conical Pick Failure, Gornoe oborudovanie i elektromekhanika, 2014, no. 1, pp. 16–23.
Dogruoz, C., Bolukbasi, N., Rostami, J., and Acar, C., An Experimental Study of Cutting Performances of Worn Picks, Rock Mech. Rock Eng., 2016, vol. 49, no. 1, pp. 213–224.
Wang, X., Su, O., Wang, Q.F., and Liang, Y.P., Effect of Cutting Depth and Line Spacing on the Cuttability Behavior of Sandstones by Conical Picks, Arabian J. Geosciences, 2017, vol. 10, no. 23, p. 525.
Zhabin, A.B., Polyakov, A.V., Averin, E.A., Linnik, Yu.N., and Linnik, V.Yu., Taking into Account Non-Optimal Modes of Rock Cutting with Conical Picks, Ugol’, 2019, no. 7, pp. 20–24.
Zhabin, A.B., Polyakov, A.V., Averin, E.A., and Sarychev, V.I., The State of Scientific Research in the Field of Rock Disintegration with a Cutting Tool at the Turn of the Century, Izv. TulGU. Nauki o Zemle, 2018, no. 1, pp. 230–247.
Shishlyannikov, D.I., Trifanov, M.G., Chekmasov, N.V., and Ivanov, S.L., Selection of Technically Justified Operating Modes for Bolter Miners Ural Based on Evaluation of Burden on their Drives in Actual Operating Conditions, Gornoe oborudovanie i elektromekhanika, 2017, no. 7, pp. 3–8.
Lukin, D.G., Yungmeister, D.A., Yacheikin, A.I., and Isaev, A.I., Improvement of the Operation of Tunneler KT 1-5.6M Cutting Head, Gornyi Zhurnal, 2018, no. 12, pp. 73–76.
Author information
Authors and Affiliations
Corresponding authors
Additional information
Translated from Fiziko-Tekhnicheskie Problemy Razrabotki Poleznykh Iskopaemykh, 2021, No. 5, pp. 114-124. https://doi.org/10.15372/FTPRPI20210511.
Rights and permissions
About this article
Cite this article
Averin, E.A., Zhabin, A.B., Polyakov, A.V. et al. Conical Pick Failure Effect on Rock Cutting Process Conditions. J Min Sci 57, 812–820 (2021). https://doi.org/10.1134/S1062739121050112
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S1062739121050112