Abstract
The inverse problem of reconstructing the surface by the signal of continuous X-ray radiation is posed in relation to the process of surfacing the roller in additive manufacturing, and its solution is also given using the iterative reconstruction method. Numerical implementation is carried out by the example of reconstruction of three types of symmetric objects: a Gaussian surface, a hemisphere, and a cylinder. The comparison showed a good correspondence of the reconstructed surfaces with the given ones.
Similar content being viewed by others
REFERENCES
Braverman, V.Ya., Analysis of the dependence of the secondary emission current and X-ray radiation on the position of the beam relative to the joint during electron beam welding, Izvestiya Samarskogo Nauchnogo Tsentra Rossiyskoy Akademii Nauk, 2016, vol. 18, nos. 2, 3, pp. 853–857.
Cooper, E.A., Logachev, P.V., Repkov, V.V., Selivanov, A.N., Selivanov, P.A., Semenov, Yu.I., Tribendis, A.G., Fedotov, M.G., and Chertovskikh, A.S., Automated system for setting seam coordinates in electron beam welding installations, Autom. Monit. Meas., 2015, vol. 51, no. 1, pp. 55–61.
Varushkin, S.V., Belenkiy, V.Y., and Trushnikov, D.N., Researching signals from workpiece backside during electron beam welding in full penetration mode, Key Eng. Mater., 2017, no. 743, pp. 231–235.
Braverman, V.Ya., Belozertsev, V.S., and Uspenskii, A.N., Experimental studies of X-ray radiation during electron beam welding, Vestn. Sib. Aerokosm. Univ. im. Reshetneva, 2005, no. 2, pp. 196–200.
Braverman, V.Ya., Bremsstrahlung X-ray radiation during electron beam welding and its relationship with process parameters, Vestn. Sib. Aerokosm. Univ. im. Reshetneva, 2008, no. 3 (20), pp. 117–121.
Trushnikov, D.N., Belenkii, V.Ya., Krotova, E.L., Permyakov, G.L., Musikhin, N.A., Olshanskaya, T.V., Salomatova, E.S., and Koleva, E.G., RF Patent 2580266, 2016.
Tereshchenko, S.A., Metodi vichislitel’noi tomografii (Methods of Computational Tomography), Moscow: Fizmatlit, 2004.
Sliva, A.P., Kharitonov, I., Goncharov, A., Dragunov, V., Gudenko, A., and Terent’ev, E., Investigation of the characterestics of ion saturation current in plasma over the keyhole in the process of electron beam welding, J. Phys. Conf. Ser., 2021, vol. 2077, p. 012019.
Trushnikov, D.N., Wire position sensor for controlling the process of electron beam layer-by-layer deposition: Modeling and verification, IEEE Sensors, 2020, vol. 21, no. 3, pp. 3134–3142.
Shcherbakov, A.V., Gaponova, D.A., and Rodyakina, R.V., Control of weld bead position in additive manufacturing process with using backscattered electrons collector signal, Russ. Internet J. Ind. Eng., 2020, vol. 7, no. 2, pp. 3–8.
Wong, H., Neary, D., Jones, E., Fox, P., and Sutcliffe, C., Pilot capability evaluation of a feedback electronic imaging system prototype for in-process monitoring in electron beam additive manufacturing, Int. J. Adv. Manuf. Technol., 2019, vol. 100, no. 1, pp. 707–720.
Trushnikov, D.N., Krotov, L.N., Krotova, E.L., and Musikhin, N.A., Reconstructing the melting channel shape in electron-beam welding from the parameters of penetrating X-ray radiation. Part I. Posing inverse geometrical problem, Russ. J. Nondestr. Test., 2016, vol. 52, no. 10, pp. 576–582.
Rikalin, N.N., Zuev, I.V., and Uglov, A.A., Osnovi elektronno-luchevoi obrabotki materialov (Fundamentals of Electron Beam Processing of Materials), Moscow: Mashinostroenie, 1978.
Bronstein, L.N., Rontgenstrahlen, Berlin: Springer, 1957.
Laptenok, V.D., Murigin, A.V., Seregin, Yu.N., and Braverman, V.Ya., Upravlenie elektronno-luchevoi svarkoi (Control of Electron Beam Welding), Krasnoyarsk: Sib. Aerokosm. Akad., 2000.
Krotova, E.L., Varushkin, S.V., and Trushnikov, D.N., Dependence of signal from continuous X-ray sensor on values of technological parameters in hybrid additive process of electron beam surfacing by wire, Russ. J. Nondestr. Test., 2022, vol. 58, no. 7, pp. 574–582.
Gordon, R., Bender, R., and Herman, G.T., Algebraic reconstruction techniques (ART) for three-dimensional electron microscopy and X-ray photography, J. Theor. Biol., 1970, vol. 29, pp. 471–481.
Volkov, E.A., Chislennie metodi (Numerical methods), Viktorenkova, I.V., Ed., Moscow: Nauka, 1987, 2nd ed.
Vasil’ev, A.A., Criteria for selection of forecast models (a review), Vestn. TvGU, 2012, no. 13, pp. 133–148.
Funding
The work was carried out with the financial support of the Russian Foundation for Basic Research in cooperation with the Perm Region (project no. 20-48-596006 r_NOTs_Permskii Krai) and the Ministry of Science and Higher Education of the Russian Federation within the framework of the national project “Science and Universities” within the framework of the state assignment “Development of scientific and technological foundations for the formation of a material-structure system with special properties based on hybrid additive technologies” no. FSNM-2021-0011.
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
The authors declare that they have no conflicts of interest.
Rights and permissions
About this article
Cite this article
Trushnikov, D.N., Krotova, E.L., Starikov, S.S. et al. Solving the Inverse Problem of Surface Reconstruction during Electron Beam Surfacing. Russ J Nondestruct Test 59, 240–250 (2023). https://doi.org/10.1134/S1061830923700249
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S1061830923700249