Abstract
The structure and tribological properties of coatings made of PN85YU15 powder were studied. The coatings were deposited on the mild steel blanks by the technology of air-plasma spraying using a unit of annular input and gas-dynamic powder focusing. Efficiency of heating and acceleration of powder particles was studied preliminarily. Measurement results on temperature and velocity distributions of particles at a certain spraying distance by the method of spectral pyrometry and time-of-flight method are presented. The effect of plasmatorch arc current and amount of propane-butane in the plasma flow on the structure and properties of coatings is analyzed in this paper. It is determined that the phase composition of coatings and initial powder is the same: the main phase is Ni3Al compound; moreover, the structure contains Ni5Al3 phase. It is shown that an increase in the amount of propane-butane increases coatings porosity. The densest coatings (5.77%) were obtained at the plasmatorch arc current of 200 A with the reduced amount of propane-butane. The coatings obtained at the minimal arc current of 100 A with an increased amount of propane-butane are characterized by maximal porosity (20.38%). The results of tribological testing of the coatings under the conditions of sliding friction with a lubricant by the disc-plane scheme are presented. From the standpoint of obtaining the densest coatings with high performance, the optimal regimes of plasma spraying of PN85YU15 powder are the current from 140 A to 200 and using the air and propane-butane mixture only as the shielding gas (anode curtain).
Similar content being viewed by others
References
Superalloys II: High-Temperature Materials for Aerospace and Industrial Power, Ch.T. Sims, N.S. Stoloff, and W.C. Hagel (Eds.), John Wiley & Sons, New York, 1987.
W.T. Hsiao, C.Y. Sua, T.S. Huang, and W.H. Liao, The microstructural characteristics and mechanical properties of Ni-Al/h-BN coatings deposited using plasma spraying, J. Alloys and Compounds, 2011, Vol. 509, Р. 8239−8245.
J.A. Hearley, J.A. Little, and A.J. Sturgeon, The effect of spray parameters on the properties of high velocity oxy-fuel NiAl intermetallic coatings, Surface and Coatings Technology, 2000, Vol. 123, P. 210–218.
S.M. Hashemi, M.H. Enayati, and M.H. Fathi, Plasma spray coatings of Ni-Al-SiC composite, J. Thermal Spray Technology, 2009, Vol. 18, P. 284–291.
M.M. Javadi, H. Edris, and M. Salehi, Plasma sprayed NiAl intermetallic coating produced with mechanically alloyed powder, J. Mater. Sci. Technol., 2011, Vol. 27, P. 816–820.
S. Sampath, X.Y. Jiang, J. Matejicek, L. Prchlik, A. Kulkarni, and A. Vaidya, Role of thermal spray processing method on the microstructure, residual stress and properties of coatings: an integrated study for Ni–5 wt. % Al bond coats, Materials Sci. and Engng, 2004, Vol. A364, P. 216–231.
W.T. Hsiao, C.Y. Sub, T.S. Huang, and W.H. Liao, Wear resistance and microstructural properties of Ni-Al/h-BN/WC-Co coatings deposited using plasma spraying, Materials Characterization, 2013, Vol. 79, P. 84–92.
L.I. Shevtsova, Structure and mechanical properties of Ni3Al intermetallic, fabricated by spark plasma sintering of mechanically activated «Ni-Al» powder mixtures, Metal Working and Material Science, 2014, Vol. 64, No. 3, P. 21–27.
B.A. Kolachev, Physical Metallurgy and Thermal Processing of Nonferrous Metals and Alloys: Text-Book for High Schools, MISiS, Moscow, 2005.
L.Y. Sheng, W. Zhang, J.T. Guo, Z.S. Wang, V.E. Ovcharenko, L.Z. Zhou, and H.Q. Ye, Microstructure and mechanical properties of Ni3Al fabricated by thermal explosion and hot extrusion, Intermetallics, 2009, Vol. 17, P. 572–577.
S.C. Deevi, V.K. Sikka, C.J. Swindeman, and R.D. Seals, Reactive spraying of nickel-aluminide coatings, J. Thermal Spray Technology, 1997, Vol. 6, Iss. 3, P. 335–344.
A. Khasui and O. Morigaki, Weldup and Spraying, V.S. Stepin and N.G. Shesterkin (Eds.), Mashinostroenie, Moscow, 1985.
E. Kornienko, E. Lapushkina, V. Kuzmin, S. Vaschenko, I. Gulyaev, E. Kartaev, D. Sergachev, N. Kashapov, S. Sharifullin, and I. Fayrushin, Air plasma sprayed coatings of self-fluxing powder materials, J. Physics: Conference Series, 2014, Vol. 567, No. 1, P. 012010-1−012010-7.
E. Kornienko, A. Smirnov, and V. Kuzmin, Structure and properties of self-fluxing coating, obtained by airplasma spraying, Applied Mechanics and Materials, 2015, Vol. 698, P. 405–410.
I.P. Gulyaev, A.V. Dolmatov, M.Yu. Kharlamov, P.Yu. Gulyaev, V.I. Jordan, I.V. Krivtsun, and O.I. Demyanov, Arc-plasma wire spraying: an optical study of process phenomenology, J. Thermal Spray Technology, 2015, Vol. 24, No. 8, P. 1566–1573.
A.V. Dolmatov, I.P. Gulyaev, and V.I. Jordan, The optical control system of dispersed phase properties in thermal spray process, IOP Conf. Series: Materials Sci. and Engng, 2015, Vol. 81, P. 012041-1–012041-9.
I.P. Gulyaev, P.Yu. Gulyaev, V.N. Korzhik, A.V. Dolmatov, V.I. Mordan, I.V. Krivtsun, M.Yu. Kharlamov, and A.I. Demianov, Experimental investigation of process of plasma-arc wire spraying, Paton Welding J., 2015, No. 3/4, P. 36–41.
I.P. Gulyaev, A.V. Dolmatov, P.Yu. Gulyaev, and M.P. Boronenko, The method of spectral-brightness pyrometry of objects with nonuniform surface temperature, RF Invention Application No. 2015123313, Priority of 17.06.2015.
S.P. Vaschenko, I.P. Gulyaev, P.Yu. Gulyaev, A.V. Dolmatov, and V.I. Kuzmin, Express-control of particle motion and heating at gas-thermal spraying, in: Proc. 17 Inter. Scientific-Practical Conf. “Technologies of hardening, deposition and repair: theory and practice”, St. Petersburg, April, 14–17, 2015, P. 61–68.
GOST 9450–76, Microhradness measuring through diamond tip indentation. Introduction, 1977-01-01, Izd. Standartov, Moscow, 1993.
Alloy Phase Diagrams, ASM Handbook, Vol. 3, 1998.
J.M. Houben and J.H. Zaat, Investigations into the mechanism of exothermically reacting nickel-aluminium spraying materials, in: Proc. Seventh Int. Metal Spray Conf., London, Sept. 1973, Welding Institute, P. 77–88.
L.I. Shevtsova, Structure and mechanical properties of materials based on nickel aluminides obtained by the technology of spark plasma sintering of powder mixtures, Theses of Candidate of technical sciences, NSTU, Novosibirsk, 2015.
S.V. Kositsyn, Phase and structural transformations in alloys of nickel monoaluminide, Uspekhi Fiziki Metallov, 2008, Vol. 9, P. 195–258.
Author information
Authors and Affiliations
Corresponding author
Additional information
The work was financially supported by the Russian Foundation for Basic Research (Project 15-33-50993).
Rights and permissions
About this article
Cite this article
Kornienko, E.E., Mul’, D.O., Rubtsova, O.A. et al. Effect of plasma spraying regimes on structure and properties of Ni3Al coatings. Thermophys. Aeromech. 23, 919–927 (2016). https://doi.org/10.1134/S0869864316060147
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0869864316060147