Abstract—
The results from experiments for studying the effect of rotor rotation on the leakage through different types of seals are presented. It is shown from a comparative study of models involving a stalled rotor and rotor rotating with a 50 Hz frequency that the rotor rotation has hardly any effect on the leakage flowrate, so that the rotation may not be taken into account in calculations of leakage flowrate through the steam turbine end and diaphragm seals. The article presents results from experiments for studying the dependence of leakage flowrate on the flow parameters, namely, the change of the velocity vector axial and circumferential components in the annular inlet channel upstream of a single annular throttle orifice. During the experiments, the velocity axial and circumferential components were varied independently and in a very significant range. The accomplished studies have shown that the change of both the axial and circumferential velocity components has hardly any effect on the leakage flowrate. It can be concluded from an analysis of the obtained results that the influence of flow parameters upstream of the seal on the leakage flowrate is so insignificant that its neglect in the previously developed calculation procedures for determining the leakage flowrate in the steam turbine seals, which are still in use at present, is quite substantiated and justified. At present, studies are being carried out that allow the flow structure in different places of turbine machinery flow paths, including the turbine seals, to be analyzed by calculation. It should be noted that it is possible by using the modern calculation methods not only to determine the vortex structure in the seal neighborhood but also to estimate the leakage flowrate, leakage losses, and even the stage efficiency for different configurations of the chamber upstream of the seal. Nonetheless, care should be taken in dealing with practical recommendations on changing the seal configurations that are based solely on the calculation results. The soundness of such recommendations must be confirmed by the relevant experimental investigations.
Similar content being viewed by others
REFERENCES
M. E. Deich and G. S. Samoilovich, Fundamentals of Aerodynamics of Axial Turbomachines (Mashgiz, Moscow, 1959) [in Russian].
V. Schramm, K. Willenborg, S. Kim, and S. Wittig, “Influence of a honeycomb facing on the flow through a stepped labyrinth seal,” J. Eng. Gas Turbines Power 124, 140–146 (2002). https://doi.org/10.1115/1.1403460
T. S. Kim and K. S. Cha, “Comparative analysis of the influence of labyrinth seal configuration on leakage behavior,” J. Mech. Sci. Technol. 23, 2830–2838 (2009). https://doi.org/10.1007/s12206-009-0733-5
I. V. Afanas’ev and A. V. Granovskii, “Computational study on the effect of shroud shape on the efficiency of the gas turbine stage,” Therm. Eng. 65, 136–142 (2018). https://doi.org/10.1134/S0040601518030011
I. V. Afanas’ev, A. V. Granovskii, E. Yu. Marchukov, I. A. Manaev, and A. E. Shunin, “Features of the vortex flow structure around a one fin shroud,” Therm. Eng. 66, 491–497 (2019). https://doi.org/10.1134/S0040601519070012
G. A. Bondarenko and V. N. Baga, “Studying the flow in the labyrinth sealing,” in Bulletin of National Technical University “Kharkiv Polytechnic Institute”: Collection of Scientific Papers, Thematical Issue: Energy and Thermotechnical Processes and Equipment (Khark. Politech. Inst., Kharkiv, 2015), pp. 23–31 [in Russian].
R. Paolillo, S. Moore, D. Cloud, and J. A. Glahn, “Impact of rotational speed on the discharge characteristic of stepped labyrinth seals,” in Proc. ASME Turbo Expo 2007: Power for Land, Sea and Air, Montreal, Canada, May 14–17, 2007 (American Society of Mechanical Engineers, New York, 2007), paper id. GT2007-28248.
V. V. Gorlach, V. L. Egorov, and N. A. Ivanov, Processing, Representation, Interpretation of Measurement Results: Study Aid, Ed. by. V. V. Gorlach (Sib. Gos. Avtomob.-Dorozhn. Akad., Omsk, 2006) [in Russian].
P. V. Novitskii and I. A. Zorgraf, Evaluation of Measurement Errors, 2nd ed. (Energoatomizdat, Leningrad, 1991) [in Russian].
H. Li-dong, Y. Xin, J. Yan, and Z. Zhen-you, “Experimental investigation of the sealing performance of honeycomb seals,” Chin. J. Aeronaut. 14, 13–17 (2001).
X. Jia, H. Zhang, Q. Zheng, S. Fan, and Z. Tian, “Investigation on rotor-labyrinth seal system with variable rotating speed,” Int. J. Turbo Jet-Eng. 36, 1–9 (2016). https://doi.org/10.1515/tjj-2016-0066
V. P. Preobrazhenskii, Thermo-Technical Measurements and Instruments: Textbook, 3rd ed. (Energiya, Moscow, 1978) [in Russian].
A. N. Petunin, Methods and Techniques for Measurements of the Parameters of a Gas Flow (Mashinostroenie, Moscow, 1972) [in Russian].
A. Egli, “Leakage of steam through labyrinth seals,” Trans. ASME 57, 115–122 (1935).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by V. Filatov
Rights and permissions
About this article
Cite this article
Dmitriev, S.S., Petrunin, B.N. & Mohamed, E.A. Experimental Studies into the Effect that the Rotor Rotation and Flow Swirling Upstream of Seals Have on the Leakage Flowrate. Therm. Eng. 68, 94–104 (2021). https://doi.org/10.1134/S0040601521010122
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0040601521010122