Abstract
Results of experimental and numerical investigations of the flow around an elongated axisymmetric body of revolution in a low-velocity wind tunnel with a closed test section and in a free flow are reported. The Reynolds number based on the body length is varied in the interval from \(2.75\cdot 10^6\) to \(9.40\cdot 10^6\). The problem is solved numerically under the assumption of an axisymmetric steady incompressible flow with the use of the ANSYS Fluent software. It is demonstrated that the test section walls produce a significant effect on the flow character and aerodynamic performances of the body of revolution for the case where the blockage factor of the test section by the body of revolution is formally within 2%.
REFERENCES
W. J. McCroskey, “A Critical Assessment of Wind Tunnel Results for the NACA 0012 Airfoil," Tech. Report No. 87-A-5 (NASA Ames Res. Center, Moffett Field, 1987).
N. Gregory and C. L. O’Reilly, “Low-Speed Aerodynamic Characteristics of NACA 0012 Airfoil Section, Including the Effects of Upper-Surface Roughness Simulating Hoar Frost," Aeronaut. Res. Counsil. Rep. Memoranda, No. 3726. (1970).
V. T. Bui and V. I. Lapygin, “Simulation of the Flow Past a Model in the Closed Test Section of a Low-Speed Wind Tunnel and in the Free Stream," Teplofiz. Aeromekh. 22 (3), 365–372 (2015) [Thermophys. Aeromech. 22 (3), 351–358 (2015)].
N. Eastern and S. Albert, “Airfoil Section Characteristics As Affected by Variations of the Reynolds Number," NACA Report No. NACA-TR-586 (1937).
S. M. Bosnyakov, V. V. Vlasenko, I. A. Kursakov, et al., “Problem of Interference of an Ogival Body of Revolution with the Sting of the Wind Tunnel and Specific Features of Solving this Problem on a Computer," Uch. Zap. TsAGI 42 (3), 25–40 (2011).
H. C. Garner, E. W. E. Rogers, W. E. A. Acum, and E. C. Maskell, “Subsonic Wind Tunnel Wall Corrections," AGARDograph Report No. 109 (1966).
S. Wiriadidjaja, M. A. S. Rafie, F. I. Romli, and O. K. Ariff, “Aerodynamic Interference Correction Methods Case: Subsonic Closed Wind Tunnels," Appl. Mech. Mater. 225, 60–66 (2012).
V. I. Kornilov, E. A. Zhkvar, and A. N. Popkov, “Influence of Distributed Blowing-in on a Turbulent Boundary Layer on a Body of Revolution," Inzh.-Fiz. Zh. 95 (1), 134–144 (2022) [J. Eng. Phys. Thermophys. 95 (1), 132–141 (2022)].
N. F. Polyakov, “Method of Studying the Flow Characteristics in a Low-Turbulence Wind Tunnel and the Transition Phenomenon in an Incompressible Boundary Layer," Candidate’s Dissertation in Tech. Sci. (Novosibirsk, 1973).
I. V. Gudilin, Yu. A. Lashkov, and V. G. Shumilkin, “Experimental Study of the Influence of Riblets and Eddy Breakup Devices on the Drag of the Body of Revolution," Izv. Akad. Nauk SSSR, Mekh. Zhidk. Gaza, No. 3, 154–157 (1996).
V. I. Kornilov, “Direct Measurements of the Drag of a Body of Revolution in an Incompressible Flow under the Action of Eddy Breakup Devices," Teplofiz. Aeromekh. 13 (4), 541–550 (2006) [Thermophys. Aeromech. 13 (4), 499–506 (2006)].
P. R. Spalart and S. R. Allmaras, “A One-Equation Turbulence Model for Aerodynamic Flows," AIAA Paper No. 92-0439 (Reno, 1992).
Computation of Turbulent Boundary Layers–1968 AFOSR-IFP Stanford Conference, Ed. by D. E. Coles and E. A. Hirst (Stanford, 1969), Vol. 2.
J. H. Preston, “The Determination of Turbulent Skin Friction by Means of Pitot Tubes," Roy. Aeronaut. Soc. 58, 109–121 (1954).
V. Patel, “Calibration of the Preston-Tube and Limitations on Its Use in Pressure Gradient," J. Fluid Mech. 23, 185–208 (1965).
A. D. Young, “The Calculation of the Total and Skin Friction Drags of Bodies of Revolution at Zero Incidence," in Report and Memoranda, No. 1874 (1939), pp. 51–70.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, 2023, Vol. 64, No. 2, pp. 27-38. https://doi.org/10.15372/PMTF20230204.
Rights and permissions
About this article
Cite this article
Kornilov, V.I., Popkov, A.N. SIMULATION OF THE FLOW AROUND AN AXISYMMETRIC BODY IN THE ABSENCE OF FREE BOUNDARIES OF THE FLOW. J Appl Mech Tech Phy 64, 198–207 (2023). https://doi.org/10.1134/S0021894423020049
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0021894423020049