Abstract
This paper describes an experimental setup consisting of a drop hammer and a shock tube filled with a liquid, where a shock wave is formed, and results of experiments performed with fully clamped rectangular plates subjected to an impact load of the water shock wave. The results are presented in terms of the central deflection of the plates as a function of the kinetic energy of the drop hammer. The singular value decomposition method is used in conjunction with dimensionless numbers to obtain analytical dependences of the central deflection of the plates on the impact load parameters.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
M. Gerdooei and B. M. Dariani, “Strain-Rate-Dependent Forming Limit Diagrams for Sheet Metals,” Proc. Inst. Mech. Eng., Pt B, J. Eng. Manufacture 222 (12), 1651–1659 (2008).
T. Kim, H. Kim, J. Bae, et al., “Semi-Solid die Forging of al6061 Wrought Aluminium Alloy with Electromagnetic Stirring,” Proc. Inst. Mech. Eng., Pt B, J. Eng. Manufacture 222 (9), 1083–1095 (2008).
O. E. Kosing and B. W. Skews, “An Investigation of High-Speed Forming of Circular Plates in a Liquid Shock Tube,” Int. J. Impact. Eng. 21 (9), 801–816 (1998).
R. Safikhani, R. Hashemi, and A. Assempour, “The Strain Gradient Approach for Determination of Forming Limit Stress and Strain Diagrams,” Proc. Inst. Mech. Eng., Pt B, J. Eng. Manufacture 222 (4), 467–483 (2008).
T. Zheng, S. H. Zhang, D. Sorgente, et al., “Approach of using a Ductile Fracture Criterion in Deep Drawing of Magnesium Alloy Cylindrical Cups under Non-Isothermal Condition,” Proc. Inst. Mech. Eng., Pt B. J. Eng. Manufacture 221 (6), 981–986 (2007).
H. Babaei, “Prediction of Deformation of Circular Plates Subjected to Impulsive Loading Using GMDH-Type Neural Network,” Int. J. Eng. Trans. A: Basics 27 (10), 1635–1644 (2014).
K. J. Astrom and P. Eykhoff, “System Identification—A Survey,” Automatica 7 (2), 123–162 (1971).
G. N. Nurick and J. B. Martin, “Deformations of Thin Plates Subjected to Impulsive Loading—A Review. 1. Theoretical Considerations,” Int. J. Impact. Eng. 8 (2), 159–170 (1989).
G. N. Nurick and J. B. Martin, “Deformation of Thin Plates Subjected to Impulsive Loading—A Review. 2. Experimental Studies,” Int. J. Impact. Eng. 8 (2), 170–186 (1989).
W. Johnson, Impact Strength of Materials (Edward Arnold, London, 1972).
N. Jones, Structural Impact (Cambridge Univ. Press, Cambridge, 1989).
N. Jacob, G. N. Nurick, and G. S. Langdon, “The Effect of Stand-Off Distance on the Failure of Fully Clamped Circular Mild Steel Plates Subjected to Blast Loads,” Eng. Structures 29 (10), 2723–2736 (2007).
Y. P. Zhao, “Suggestion of a New Dimensionless Number for Dynamic Plastic Response of Beams and Plates,” Arch. Appl. Mech. 68 (7/8), 524–538 (1998).
H. Gharababaei, N. Nariman-Zadeh, and A. Darvizeh, “A Simple Modelling Method for Deflection of Circular Plates under Impulsive Loading Using Dimensionless Analysis and Singular Value Decomposition,” J. Mech. 26 (3), 355–361 (2010).
W. Q. Shen, “Dynamic Response of Rectangular Plates under Drop Mass Impact,” Int. J. Impact. Eng. 19 (3), 207–229 (1997).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 58, No. 1, pp. 158–167, January–February, 2017.
Rights and permissions
About this article
Cite this article
Babaei, H., Mirzababaie Mostofi, T., Alitavoli, M. et al. Experimental investigation and dimensionless analysis of forming of rectangular plates subjected to hydrodynamic loading. J Appl Mech Tech Phy 58, 139–147 (2017). https://doi.org/10.1134/S0021894417010151
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0021894417010151