Abstract
The electroplastic effect (EPE) is a phenomenon which consists in a decrease in the strain resistance and enhancement of the plasticity of metals under the effect of the electric current of a sufficiently high density [1]. This study aims to compare the deformation behavior of single-phase commercially pure titanium Grade 4 and two-phase VT6 alloy under tension and external heating with the introduction of a pulsed current. Current of various pulse ratios and densities is supplied to the grips of the tensile testing machine from a pulse generator. To estimate the relative contribution of the electroplastic effect during passage of current to the reduction of flow stresses, the materials are also exposed to external heating. The microstructure of the samples in the sample head and in the vicinity of the fracture region in the longitudinal section is studied using optical microscopy. The electroplastic effect in the studied materials is manifested on the tensile curve through individual jumps in the downward flow stress at a high pulse ratio, whereas at a low current pulse ratio a decrease in the flow stress and strain hardening and increase in the plasticity are observed. It is shown that the tension of the sample under the effect of current results in a greater decrease in the flow stresses than that observed under external heating at the same temperature for both materials. This confirms the athermal nature of the pulsed current effect. The critical density of the high pulse ratio current (q = 5000) capable of providing manifestation of the electroplastic effect is two times lower for the VT6 alloy than for the pure titanium Grade 4. Under the same pulsed current modes, the flow stresses for VT6 decrease more than for Grade 4. The pulsed current of high pulse ratio caused an anomalous hardening effect in the VT6 alloy, but the physical nature of this effect requires an additional study. The pulsed current modes used in the study did not lead to any structural changes noticeable under optical magnification in the samples under tension, except for the disappearance of twins and separation of the impurity particles in Grade 4 and spheroidization of grains in VT6.
REFERENCES
Troitsky, O.A., Elektroplasticheskii effekt v metallakh (Electroplastic Effect in Metals), Moscow: Kim L.A., 2021.
Moon-Jo, K., Sangmoon, Y., Siwook, P., et al., Elucidating the origin of electroplasticity in metallic materials, Appl. Mater. Today, 2020, vol. 1, p. 100874. https://doi.org/10.1016/j.apmt.2020.100874
Troitsky, O.A., Stashenko, V.I., and Skvortsov, O.B., Vibrations of conductors during the transmission of pulsed electric current and non-destructive testing, Inzh. Zh. Nauka Innov., 2018, no. 3, pp. 1–15.
Gennari, C., Calliari, I., and Stolyarov, V., Electroplastic effect in specimens of duplex stainless steel under tension, Zavod. Lab. Diagn. Mater., 2020, vol. 86, no. 10, pp. 41–45. https://doi.org/10.26896/1028-6861-2020-86-10-41-45
Minko, D.V., Analysis of the prospects for the use of EPE in OMD processes, Lit’ye Metall., 2020, no. 4, pp. 125–130. https://doi.org/10.21122/1683-6065-2020-4-125-130
Fan, R., Magargee, J., Hu, P., and Cao, J., Influence of grain size and grain boundaries on the thermal and mechanical behavior of 70/30 brass under electrically-assisted deformation, Mater. Sci. Eng. A, 2013, no. 574, pp. 218–225. https://doi.org/10.1016/j.msea.2013.02.066
Tiwari, J., Balaji, V., Krishnaswamy, H., and Amirthalingam, M., Dislocation density based modelling of electrically assisted deformation process by finite element approach, Int. J. Mech. Sci., 2022, no. 227, p. 107433. https://doi.org/10.1016/j.ijmecsci.2022.107433
Ao, D., Chu, X., Yang, Y., Lin, S., and Gao, J., Effect of electropulsing on springback during V-bending of Ti-6Al-4V titanium alloy sheet, Int. J. Adv. Manuf. Technol., 2018, no. 96, pp. 3197–3207. https://doi.org/10.1007/s00170-018-1654-1
Kinsey, B., Cullen, G., Jordan, A., and Mates, S., Investigation of electroplastic effect at high deformation rates for 304SS and Ti-6Al-4V, CIRP Ann., 2013, vol. 62, no. 1, pp. 279–282. https://doi.org/10.1016/j.cirp.2013.03.058
Okazaki, K., Kagawa, M., and Conrad, H., An evaluation of the contributions of skin, pinch and heating effects to the electroplastic effect in titanium, Mater. Sci. Eng., 1980, no. 45, pp. 109–116.
Ao, D., Chu, X., Lin, S., Yang, Y., and Gao, J., Hot tensile behaviors and microstructure evolution of Ti-6Al-4V titanium alloy under electropulsing, Acta Metall. Sin., 2018, no. 31, pp. 1287–1296. https://doi.org/10.1007/s40195-018-0735-3
Stolyarov, V.V., Peculiarities of tension diagrams of shape memory alloys under the influence of current, Zavod. Lab. Diagn. Mater., 2013, vol. 79, no. 9, pp. 64–67.
Pakhomov, M. and Stolyarov, V., Specific features of electroplastic effect in mono- and polycrystalline aluminum, Met. Sci. Heat Treatm., 2021, no. 63, pp. 236–242. https://doi.org/10.1007/s11041-021-00677-7
Adabala, S., Cherukupally, S., Guha, S., et al., Importance of machine compliance to quantify electro-plastic effect in electric pulse aided testing: An experimental and numerical study, J. Manuf. Process., 2022, vol. 75, pp. 268–279. https://doi.org/10.1016/j.jmapro.2021.12.027
Titanium Alloys–Physical Properties, AZO Materials. https:// www.azom.com/article.aspx?ArticleID=1341.
Zhao, S., Zhang, R., Li, X., et al., Defect reconfiguration in a Ti-Al alloy via electroplasticity, Nat. Mater., 2021, no. 20, pp. 468–472. https://doi.org/10.1038/s41563-020-00817-z
Stolyarov, V.V., Electroplastic effect in nanocrystalline and amorphous alloys, Mater. Sci. Technol., 2015, vol. 31, no. 13a, pp. 1536–1540. https://doi.org/10.1179/1743284715Y.0000000008
Stolyarov, V.V., Influence of chemical and phase composition on the emergence of the electroplastic effect in titanium alloys, Bull. Russ. Acad. Sci.: Phys., 2014, vol. 78, no. 3, pp. 234–236.
Rudolf, C., Goswami, R., Kang, W., and Thomas, J., Effects of electric current on the plastic deformation behavior of pure copper, iron, and titanium, Acta Mater., 2021, vol. 209, p. 116776. https://doi.org/10.1016/j.actamat.2021.116776
Funding
This work was supported by the Ministry of Science and Higher Education of the Russian Federation, project no. 075-15-2021-709, unique ID project identifier RF‑2296. 61321X0037 (control measurements).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors of this work declare that they have no conflicts of interest.
Additional information
Translated by N. Saetova
Publisher’s Note.
Pleiades Publishing remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Korolkov, O.E., Pakhomov, M.A. & Stolyarov, V.V. Electroplastic Effect in Titanium Alloys Under Tension. Inorg Mater 59, 1581–1589 (2023). https://doi.org/10.1134/S0020168523150050
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0020168523150050