Abstract
The microstructure and the mechanical properties of stud metal (steel 40Kh) M90×4 for fixing covers of large hydraulic units were studied. The mechanical properties were determined by static, dynamic, and cyclic tests of samples cut out of a stud in the longitudinal and transverse directions and at different distances from the surface. The character of the change in the microstructure and the mechanical properties over the cross section of a stud was determined. Static and cyclic tests of model and actual studs together with nuts were performed. The load and stress values under which the chain cutting of turns of a threaded joint occurs were determined. A strong influence of the scale factor on the durability of studs was established by cyclic tests.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Matyunin, V.M., Operativnaya diagnostika mekhanicheskikh svoistv konstruktsionnykh materialov (Rapid Testing of Mechanical Properties of Structural Materials), Moscow: Mosk. Energ. Inst., 2006.
Birger, I.A., Shorr, B.F., and Iosilevich, G.B., Raschet na prochnost’ detalei mashin (Strength Calculation of Machine Elements), Moscow: Mashinostroenie, 1993.
Qui, H., Kawaguchi, Y., and Shiga, C., Charpy impact behavior of ultrafine grained steels, Proc. Charpy Centenary Conf. France, Poiters, 2001, vol. 1, pp. 275–282.
Uzhik, G.V., Prochnost’ metallov v mashinostroenii (Strength of Metals in Mechanical Engineering), Moscow: Trudrezervizdat, 1958.
Serensen, S.V., Kogaev, V.P., and Shneiderovich, R.M., Nesushchaya sposobnost’ i raschety detalei mashin na prochnost’ (Carrying Force and Strength Calculations of Machine Elements), Moscow: Mashinostroenie, 1975.
Kogaev, V.P., Raschety na prochnost’ pri napryazheniyakh, peremennykh vo vremeni (Strength Calculations of Structures under Time-Varying Stresses), Moscow: Mashinostroenie, 1993.
Kazantsev, A.G., Ivanov, S.V., Rudak, V.V., Kakhadze, M.Zh., and Kabelevskii, M.G., Fatigue Strength of Threaded Joints of an Attachment Point of a Hydraulic Turbine Cover, Tyazh. Mashinostr., 2014, no. 9, pp. 6–9.
Makhutov, N.A., Petrenya, Yu.K., Gadenin, M.M., and Ivanov, S.V., Evaluation Factors of Stressed States, Strength, and Service Life of Important Threaded Joints, Zavod. Lab., Diagn. Mater., 2014, vol. 80, no. 7, pp. 44–54.
Georgievskaya, E.V. and Smelkov, L.L., Evaluation of strength and residual life of hydraulic turbines: problems and solutions, Mater. vos’moi nauchno-tekh. konf. “Gidroenergetika. Novye razrabotki i tekhnologii” (Proc. 8th Sci.-Tech. Conf. “Hydropower: New Developments and Technologies”), St. Petersburg, 2014.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © V.M. Matyunin, B.M. Orakhelashvili, A.Yu. Marchenkov, A.G. Kazantsev, M.Zh. Kakhadze, K.A. Soin, 2015, published in Zavodskaya Laboratoriya, Diagnostika Materialov, 2015, Vol. 81, No. 9, pp. 59–66.
Rights and permissions
About this article
Cite this article
Matyunin, V.M., Orakhelashvili, B.M., Marchenkov, A.Y. et al. Static, dynamic, and cyclic strength of stud metal in large hydraulic units. Inorg Mater 52, 1520–1527 (2016). https://doi.org/10.1134/S0020168516150139
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0020168516150139