Advertisement

Russian Metallurgy (Metally)

, Volume 2019, Issue 13, pp 1531–1536 | Cite as

Comparative Analysis of the Mechanical Properties of the Friction Stir Welding Joints of Various Aluminum Alloys

  • E. N. Ryl’kovEmail author
  • F. Yu. Isupov
  • A. A. Naumov
  • O. V. Panchenko
  • L. A. Zhabrev
PROCESSES OF MANUFACTURE OF FERROUS AND NONFERROUS METALS

Abstract

The technological features of friction stir welding of the most widely used aluminum alloys, namely, Al–Si, Al–Mg, and Al–Mg–Mn, are considered and generalized. The structure and the mechanical properties of the welded joints of these alloys are analyzed.

Keywords:

friction stir welding joint aluminum alloys mechanical properties microstructure microhardness 

Notes

FUNDING

This work was performed in terms of the federal program Research and Development in the Priority Fields of the Russian Scientific and Technological Complex in 2014–2020 (project no. RFMEFI57517X0155).

REFERENCES

  1. 1.
    R. S. Mishra, “Friction stir welding and processing,” Mater. Scie. Eng. 50, 1–78 (2005).CrossRefGoogle Scholar
  2. 2.
    S. J. Maddox, “Review of fatigue assessment procedures for aluminium structures,” Int. J. Fatigue, No. 25, 1359–1378 (2003).CrossRefGoogle Scholar
  3. 3.
    M. M. Shtrikman, “Current state and development of friction stir welding. Part 3. Industrial application of friction stir welding,” Weld. Int. 53, 980–1023 (2008).Google Scholar
  4. 4.
    S. Amini, M. R. Amiri, and A. Barani, “Investigation of tool geometry on friction stir welding of 5083-O aluminum alloy,” Int. J. Adv. Manuf. Technol., No. 76, 255–261 (2005).Google Scholar
  5. 5.
    A. H. Jamshidi, S. Serajzadeh, and A. H. Kokabi, “Theoretical and experimental investigation into friction stir welding of AA 5086,” Int. J. Adv. Manuf. Technol., No. 52, 531–544 (2011).Google Scholar
  6. 6.
    A. Haboudou et al., “Reduction of porosity content generated during Nd:YAG laser welding of A356 and AA5083 aluminium alloys,” Mater. Sci. Eng. A, No. 363, 40–52 (2003).CrossRefGoogle Scholar
  7. 7.
    A. I. Rudskoy et al., “Advanced metallic materials and processes,” Mater. Phys. Mechan., No 25 (1), 1–8 (2016).Google Scholar
  8. 8.
    M. A. Sutton, B. Y. Yang, A. P. Reynolds, and R. Taylor, “Microstructural studies of friction stir welds in 2024-T3 aluminum,” Mater. Sci. Eng. A, No. 323, 60–166 (2003).CrossRefGoogle Scholar
  9. 9.
    W. Arbegast and P. J. Hartley, “Friction stir weld technology development at Lockheed,” in Proceedings of Fifth International Conference on Trends in Welding Research (1998).Google Scholar
  10. 10.
    J. H. Ouyang and R. Kovacevic, “Materials flow and microstructure in the friction stir butt welds of the same and dissimilar aluminum alloys,” Mater. Eng. Perform. 11, 50–84 (2002).CrossRefGoogle Scholar

Copyright information

© Pleiades Publishing, Ltd. 2019

Authors and Affiliations

  • E. N. Ryl’kov
    • 1
    Email author
  • F. Yu. Isupov
    • 1
  • A. A. Naumov
    • 1
  • O. V. Panchenko
    • 1
  • L. A. Zhabrev
    • 1
  1. 1.New Industrial Technologies Center, Peter the Great St. Petersburg Polytechnic UniversitySt. PetersburgRussia

Personalised recommendations