Journal of Applied Mechanics and Technical Physics

, Volume 59, Issue 6, pp 1104–1110 | Cite as

Nonlinear Delamination Analysis of Mulyilayered Functionally Graded Circular Shafts in Torsion

  • V. I. RizovEmail author


Cylindrical delamination in a multilayered functionally graded circular shaft loaded in torsion is analyzed assuming a nonlinear mechanical behaviour of the material by using the Ramberg–Osgood equation. The shaft is made of an arbitrary number of adhesively bonded concentric layers of different thicknesses and material properties. In each layer, the material is functionally graded in both radial and longitudinal directions. A solution for the strain energy release rate is derived by analyzing the energy balance. The solution is used to perform parametric investigations of the delamination behaviour.


multilayered circular shaft functionally graded material cylindrical delamination material nonlinearity analytical solution 


Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.


  1. 1.
    M. M. Nemat-Allal, M. H. Ata, M. R. Bayoumi, and W. Khair-Eldeen, “Powder Metallurgical Fabrication and Microstructural Investigations of Aluminum/Steel Functionally Graded Material,” Materials Sci. Appl. 2, 1708–1718 (2011).Google Scholar
  2. 2.
    S. K. Bohidar, R. Sharma, and P. R. Mishra, “Functionally Graded Materials: A Critical Review,” Int. J. Res. 1, 289–301 (2014).Google Scholar
  3. 3.
    M. Uslu Uysal, “Buckling Behaviors of Functionally Graded Polymeric Thin-Walled Hemispherical Shells,” Steel Composite Structures. Int. J. 21, 849–862 (2016).CrossRefGoogle Scholar
  4. 4.
    F. G. Guadette, A. E. Giannapoulos, and S. Suresh, “Interfacial Cracks in Layered Materials Subjected to a Uniform Temperature Change,” Int. J. Fracture 28, 5620–5629 (2001).Google Scholar
  5. 5.
    J. A. Narin, “On the Calculation of Energy Release Rates for Cracked Laminates with Residual Stresses,” Int. J. Fracture 139, 267–293 (2006).CrossRefGoogle Scholar
  6. 6.
    C. H. Hsueh, W. H. Tuan, and W. C. J. Wei, “Analyses of Steady-State Interface Fracture of Elastic Multilayered Beams under Four-Point Bending,” Scripta Materialia 60, 721–724 (2009).CrossRefGoogle Scholar
  7. 7.
    A. Szekrenyes, “Fracture Analysis in the Modified Split-Cantilever Beam using the Classical Theories of Strength of Materials,” J. Phys.: Conf. Ser. 240, 012030 (2010).Google Scholar
  8. 8.
    V. I. Rizov, “Elastic–Plastic Fracture of Functionally Graded Circular Shafts in Torsion,” Adv. Materials Res. 5, 299–318 (2016).CrossRefGoogle Scholar
  9. 9.
    V. I. Rizov, “Delamination Analysis of a Layered Elastic–Plastic Beam,” Int. J. Structur. Integrity 4, 516–529 (2017).CrossRefGoogle Scholar
  10. 10.
    V. I. Rizov, “Delamination in a Two-Dimensional Functionally Graded Beam,” Prikl. Mekh. Tekh. Fiz. 59 (1), 171–177 (2018) [J. Appl. Mech. Tech. Phys. 59 (1), 146–152 (2018)].MathSciNetGoogle Scholar

Copyright information

© Pleiades Publishing, Inc. 2018

Authors and Affiliations

  1. 1.University of ArchitectureCivil Engineering and GeodesySofiaBulgaria

Personalised recommendations