Skip to main content
SpringerLink
Log in

Design and fabrication of an impulse measurement device to quantify the blast environment from a near-surface detonation in soil

  • Techniques
  • Published:
Experimental Techniques Aims and scope Submit manuscript

Summary

A reusable IMD was designed to directly measure the combined aboveground soil debris and airblast loadings from the detonation of surface and shallow-buried explosive charges. The IMD was designed with a mass piston assembly that was free to move in a vertical direction with minimal resistance other than its own weight and gravity. Through calibration and testing, the IMD proved to be reliable and reusable with very few maintenance issues. Comparison of the experimental data with the results of the CTH calculations shows good agreement and indicate that the IMD performed as designed. The peak velocity and displacement data captured in the IMD were within 5 percent of the CTH calculated values. The displacement of the support structure recorded during the blast event was well below the design goals and proved to have little or no influence on the response of the IMD. The tests performed with the IMD were very successful in capturing critical information. Follow-on experiments to investigate the effects of shallow buried explosive detonations in soils will provide critical data needed to validate numerical codes and constitutive models used to predict loading on vehicle by IED and mine blast.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Bitting, R.L., Structural Analysis of the Vertical Impulse Measurement Fixture, ARL-TR-2464, Army Research Laboratory, Adelphi, MD (2001).

    Google Scholar 

  2. Grujicic, M., Pandurangan, B. and Cheeseman, B.A., “The Effect of Degrees of Saturation of Sand on Detonation Phenomena Associated with Shallow-Buried and Ground-Laid Mines,” Shock and Vibration Journal 13:41–61 (2005).

    Article  Google Scholar 

  3. Snyman, I.M., and Reinecke, J.D., “Measuring the Impulse from an Explosive Charge,” 5th South African Ballistics Symposium, OTB, Western Cape, South Africa; August 7 (2006).

  4. American Institute of Steel Construction, Inc., Load and Resistance Factor Design, Manual of Steel Construction, Volume I, Structural Members, Specifications, and Codes, American Institute of Steel Construction, Inc., Chicago, IL (1994).

    Google Scholar 

  5. USACE Protective Design Center, User’s Guide for the Single-Degree-of-Freedom Blast Effects Design Spreadsheets (SBEDS), PDC-TR-06-02, US Army Corps of Engineers Protective Design Center, Omaha, NE (2006).

    Google Scholar 

  6. USACE Protective Design Center, Single-Degree of Freedom Plastic Analysis for Windows (SPAn32), US Army Corps of Engineers Protective Design Center, Omaha, NE (2002).

    Google Scholar 

  7. Research Engineers, International, STAAD.Pro, Research Engineers Corp. Headquarters, Yorba Linda, CA (2005).

    Google Scholar 

  8. Intertechnology, Inc., Celesco Model PT-101, Cable Extension Position Transducer, Don Mills, Ontario, Canada (2007).

    Google Scholar 

  9. Endevco Corporation, Product data sheet, Model 7270A, San Juan Capistrano, CA (2005).

  10. Kulite Semiconductor, “Kulite Miniature IS Silicon Diaphragm Pressure Transducers,” Kulite Semiconductor Products, Leonia, NJ (2007).

  11. PCB Piezotronics Inc., Piezoelectric Pressure Sensor, New York (2008).

  12. Hi-Techniques, Inc., Win600e/meDAQ Data Acquisition Systems, Madison, WI (2004).

  13. McGlaun, J.M., Thompson, S.L., and Elrick, M.G., “CTH: a Three-Dimensional Shock Physics Code,” International Journal of Impact Engineering 10(351–360):(1990).

  14. Baylot, J.T., and Bevins, T.L., “Effect of Responding and Failing Structural Components on the Airblast Pressures and Loads on and Inside of the Structure,” Computers and Structures 85:(2007).

  15. Joachim, C.E., McMahon, G.W., Lunderman, C.V., and Garner, S.B., Airblast Effects Research: Small-Scale Experiments and Calculations, US Army Engineer Waterways Experiment Station, Vicksburg, MS, Technical Report SL-99-5 (1999).

    Book  Google Scholar 

  16. Namburu, R.R., Armstrong, B.J., and Bevins, T.L., “Effects of Water Tamping on Airblast and Cratering from an above Ground Cylindrical Charge,” 29th Plasmadynamics and Lasers Conference, Albuquerque, NM; June 15–18 (1998).

  17. Vision Research, “Phantom v7.3 High Speed Digital Imaging System,” Wayne, NJ (2009).

Download references

Author information

Authors and Affiliations

  1. US Army Corps of Engineers, Engineer Research and Development Center, Vicksburg, MS, USA

    J. Q. Ehrgott Jr. (research civil engineer), R. G. Rhett (mechanical engineer), S. A. Akers (research civil engineer) & D. D. Rickman (research physicist)

Authors
  1. J. Q. Ehrgott Jr.
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. R. G. Rhett
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. A. Akers
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. D. D. Rickman
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ehrgott, J.Q., Rhett, R.G., Akers, S.A. et al. Design and fabrication of an impulse measurement device to quantify the blast environment from a near-surface detonation in soil. Exp Tech 35, 51–62 (2011). https://doi.org/10.1111/j.1747-1567.2009.00604.x

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1111/j.1747-1567.2009.00604.x

Search

Navigation