This is a preview of subscription content, log in via an institution to check access.
References
Cingi, C., “Misura di Tensioni Residue in Compoenenti Strutturali col Metodo di Mathar,” Degree Thesis, reporters: Freddi, A., Curioni, S. and Veschi, D., Dep. of Eng., Univ. of Bologna (1980–81).
Cingi, C., “Problemi Applicativi nella Misura delle Tensioni Residue col Metodo di Mathar,” Ingegneria Automotoristica, 37(8–9), 484–490 (Aug.–Sept. 1984).
Soete, W. and Vancombrugge, R., “An Industrial Method for the Determination of Residual Stresses,” Proc. SESA, 8(1), 17–28 (1950).
Kelsey, R.A., “Measuring Non-Uniform Residual Stresses by the Hole Drilling Method,” Proc. SESA, 14(1), 181–194 (1956).
Rendler, N. and Vigness, I., “Hole-Drilling Strain-Gage Method of Measuring Residual Stresses,” EXPERIMENTAL MECHANICS, 16(12), 577–586 (Dec. 1966).
Bathgate, R.G., “Measurement of Non-Uniform Bi-Axial Residual Stresses by the Hole-Drilling Method,” STRAIN, 4(2), 20–29 (Apr. 1968).
Gupta, B.P., “Hole Drilling Technique: Modifications in the Analysis of Residual Stresses,” EXPERIMENTAL MECHANICS, 13(1), 45–48 (Jan. 1973).
Beaney, E.M., “Accurate Measurement of Residual Stresses in any Steel Using the Center-Hole Method,” STRAIN, 2(3), 99–106 (July 1976).
Bynum, J.E., “Modifications to the Hole-Drilling Technique of Measuring Residual Stresses for Improved Accuracy and Reproducibility,” EXPERIMENTAL MECHANICS, 21(1), 21–33 (Jan. 1981).
ASTM Standard E 837-81, “Standard Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method.”
Ajovalasit, A., “Analisi delle Tensioni Residue con il Metodo della Rosetta Forata: Influenza dell’eccentricità Foro-Rosetta,” Report of the Mach. Design Inst., Univ. of Palermo, 8 (1978).
Mandorini, V., Ghelardoni, E. and Tribuno, C., “Influenza della Curvatura della Superficie sulla Misura delle Tensioni residue Mediante il Metodo del Foro Cieco,” Proc. of 9th Nat. Meet. of AIAS (Ital. Soc. for Stress Anal.), 53–62 (1981).
Witt, F., Lee, F. and Rider, W., “A Comparison of Residual-Stress Measurements Using Blind-Hole, Abrasive-Jet and Trepan-Ring Methods,” EXPERIMENTAL TECHNIQUES, 7(2), 41–44 (Feb. 1983).
Majid Kabir, “Measurement of Residual Stresses by the Hole-Drilling Method: Influence of Transverse Sensitivity of the Gages and Relaxed-Strain Coefficients,” EXPERIMENTAL MECHANICS, 24(3), 252–256 (Sept. 1984).
Majid Kabiri, “Nonuniform Residual-Stress Measurement by the Hole-Drilling Technique,” EXPERIMENTAL MECHANICS, 24(4), 328–336 (Dec. 1984).
Tieu, A.K., “A Direct Method to Evaluate Hole-Alignment Error in Residual-Stress Measurement,” EXPERIMENTAL MECHANICS, 25(1), 43–47 (Mar 1985).
Flaman, M.T. and Herring, J.A., “Comparison of Four Hole-Producing Techniques for the Center-Hole Residual-Stress Measurement Method,” EXPERIMENTAL TECHNIQUES, 9(8), 30–32 (Aug. 1985).
Niku-Lari, A., Lu, J. and Flavenot, J.F., “Measurement of Residual-Stress Distribution by the Incremental Hole-Drilling Method,” EXPERIMENTAL MECHANICS, 25(2), 175–185 (June 1985).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Cingi, C. Some considerations relating to Mathar’s method for measuring residual stresses. Exp Tech 11, 21–23 (1987). https://doi.org/10.1111/j.1747-1567.1987.tb00622.x
Published:
Issue Date:
DOI: https://doi.org/10.1111/j.1747-1567.1987.tb00622.x