Abstract
Purpose. The purpose of this study was to use polymer blends for the coating of pellets and to study the effects of the type of coating technique (aqueous vs. organic) on drug release.
Methods. Propranolol HCl-loaded pellets were coated with blends of a water-insoluble and an enteric polymer (ethyl cellulose and Eudragit L). Drug release from the pellets as well as the mechanical properties, water uptake, and dry weight loss behavior of thin polymeric films were determined in 0.1 M HCl and phosphate buffer, pH 7.4.
Results. Drug release strongly depended on the type of coating technique. Interestingly, not only the slope, but also the shape of the release curves was affected, indicating changes in the underlying drug release mechanisms. The observed effects could be explained by the higher mobility of the macromolecules in organic solutions compared to aqueous dispersions, resulting in higher degrees of polymer-polymer interpenetration and, thus, tougher and less permeable film coatings. The physicochemical properties of the latter were of major importance for the control of drug release, which was governed by diffusion through the intact polymeric films and/or water-filled cracks.
Conclusions. The type of coating technique strongly affects the film microstructure and, thus, the release mechanism and rate from pellets coated with polymer blends.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
references
J. W. McGinity. Aqueous Polymeric Coatings for Pharmaceutical Dosage Forms, 2nd Ed., Marcel Dekker, New York, 1997.
Y. Fukumori. Coating of Multiparticulates Using Polymeric Dispersions. In I. Ghebre-Sellassie (ed.), Multiparticulate Oral Drug Delivery, Marcel Dekker, New York, 1997, pp. 79–111.
S. T. Eckerseley and A. Rudin. Mechanism of film formation from polymer latexes. Journal of Coatings Technology 62:89–100 (1990).
J. C. Gutierrez-Rocca and J. W. McGinity. Influence of aging on the physical-mechanical properties of acrylic resin films cast from aqueous dispersions and organic solutions. Drug Dev. Ind. Pharm. 19:315–332 (1993).
C. A. Lorck, P. C. Grunenberg, H. Jüunger, and A. Laicher. Influence of process parameters on sustained-release theophylline pellets coated with aqueous polymer dispersions and organic solvent-based polymer solutions. Eur. J. Pharm. Biopharm. 43:149–157 (1997).
A. Garcia-Arieta, D. Torrado-Santiago, and J. J. Torrado. Comparative study of aqueous and organic enteric coatings of chlorpheniramine maleate tablets. Drug Dev. Ind. Pharm. 22:579–585 (1996).
U. Iyer, W. H. Hong, N. Das, and I. Ghebre-Sellassie. Comparative evaluation of three organic solvent and dispersion-based ethylcellulose coating formulations. Pharm. Technol. 14:68–86 (1990).
M. Wesseling and R. Bodmeier. Drug release from beads coated with an aqueous colloidal ethylcellulose dispersion, Aquacoat®, or an organic ethylcellulose solution. Eur. J. Pharm. Biopharm. 47:33–38 (1999).
R. Bodmeier and O. Paeratakul. Mechanical properties of dry and wet cellulosic and acrylic films prepared from aqueous colloidal polymer dispersions used in the coating of solid dosage forms. Pharm. Res. 11:882–888 (1994).
F. Lecomte, J. Siepmann, M. Walther, R. J. MacRae, and R. Bodmeier. Blends of enteric and GIT-insoluble polymers used for film coating: physicochemical characterization and drug release patterns. J. Control. Rel. 89:457–471 (2003).
K. Amighi, J. Timmermans, J. Puigdevall, E. Baltes, and A. J. Moes. Peroral sustained-release film coated pellets as a means to overcome physicochemical and biological drug-related problems. I. In vitro development and evaluation. Drug Dev. Ind. Pharm. 24:509–515 (1998).
T. Y. Fan, S. L. Wei, W. W. Yan, D. B. Chen, and J. Li. An investigation of pulsatile release tablets with ethyl cellulose and Eudragit L as film coating materials and cross-linked polyvinylpyrrolidone in the core tablets. J. Control. Rel. 77:245–251 (2001).
C. L. Zhao, Y. Wang, Z. Hruska, and M. A. Winnik. Molecular aspects of latex film formation: an energy-transfer study. Macromolecules 23:4082–4087 (1990).
O. Pekcan and M. A. Winnik. Fluorescence studies of coalescence and film formation in poly(methyl methacrylate) nonaqueous dispersions particles. Macromolecules 23:2673–2678 (1990).
J. L. Keddie, P. Meredith, R. A. L. Jones, and A. M. Donald. Kinetics of film formation in acrylic latices studied with multiple-angle-of-incidence ellipsometry and environmental SEM. Macromolecules 28:2673–2682 (1995).
E. M. Boczar, B. C. Dionne, Z. Fu, A. B. Kirk, P. M. Lesko, and A. D. Koller. Spectroscopic studies of polymer interdiffusion during film formation. Macromolecules 26:5772–5781 (1993).
O. Vorobyova and M. A. Winnik. Morphology of poly(2-ethylhexyl methacrylate):poly(butyl methacrylate) latex blend films. Macromolecules 34:2298–2314 (2001).
G. S. Rekhi, S. C. Porter, and S. S. Jambhekar. Factors affecting the release of propranolol hydrochloride from beads coated with aqueous polymer dispersions. Drug Dev. Ind. Pharm. 21:709–729 (1995).
R. U. Nesbitt, M. Mahjour, N. L. Mills, and M. B. Fawzi. Effect of substrate on mass release from ethylcellulose latex coated pellets. J. Control. Rel. 32:71–77 (1994).
J. Hjärtstam, K. Borg, and B. Lindstedt. The effect of tensile stress on permeability of free films of ethylcellulose containing hydroxypropyl methylcellulose. Int. J. Pharm. 61:101–107 (1990).
J. Hjärtstam and T. Hjertberg. Swelling of pellets coated with a composite film containing ethyl cellulose and hydroxypropyl methylcellulose. Int. J. Pharm. 161:23–28 (1998).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lecomte, F., Siepmann, J., Walther, M. et al. Polymer Blends Used for the Coating of Multiparticulates: Comparison of Aqueous and Organic Coating Techniques. Pharm Res 21, 882–890 (2004). https://doi.org/10.1023/B:PHAM.0000026443.71935.cb
Issue Date:
DOI: https://doi.org/10.1023/B:PHAM.0000026443.71935.cb