Abstract
Sol-gel hybrid organic-inorganic and inorganic SiO2-based protective coatings with and without added 3 μm glass particles were developed and tested for their corrosion and wear behavior of an stainless steel substrate (AISI316L). The corrosion resistance greatly increases by incorporating glass particles in the sols. The incorporation of particles in the coatings allows the synthesis of thicker crack-free coatings. On the other hand, the corrosion resistance increases for coatings with a higher organic content obtained at lower sintering temperature. These coatings are also highly stable in saline aqueous solutions. However, the wear resistance is badly affected by the hybrid character of the SiO2 matrix. The optimum coating process in terms of corrosion and wear resistance, appears to be a hybrid system with a dense SiO2 network achieved at intermediate sintering temperatures.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
C.J. Brinker and G.W. Scherer, Sol-Gel Science: The Physics and Chemistry of Sol-Gel Processing (Academic Press, San Diego, 1990), pp. 787 and 839–880.
O de Sanctis, L. Gómez, A. Marajofsky, C. Parodi, N. Pellegri, and A. Durán, J. Non-Cryst. Solids 121, 315 (1990).
M. Guglielmi, J. Sol-Gel Sci. Technol. 8, 443 (1997).
P. Innocenzi, M. Guglielmi, M. Gobbin, and P. Colombo, J. Eur. Ceram. Soc. 10, 431 (1992).
K. Izumi, H. Tanaka, Y. Uchida, N. Tohge, and T. Minami, J. Mater. Sci. Lett. 12, 724 (1993).
V.J. Wen, V.J. Vasudevan, and G.L. Wilkes, J. Sol-Gel Sci. Technol. 5, 115 (1995).
P. Galliano, J. de Damborenea, M.J. Pascual, and A. Durán, J. Sol-Gel Sci. Technol. 13, 723 (1998).
P. Innocenzi, M.O. Abdirashid, and M. Guglielmi, J. Sol-Gel Sci. Technol. 3, 47 (1994).
J. Oh, H. Imai, and K. Tsukuma, J. Mater. Res. 12, 1008 (1997).
H. Schmidt, J. Non-Cryst. Solids 73, 681 (1985).
J.D. Mackenzie, J. Sol-Gel Sci. Technol. 2, 81 (1994).
A. Durán, Bol. Soc. Esp. Ceram. Vidr. 25, 395 (1986).
M. Guglielmi, J. Sol-Gel Sci. Technol. 8, 443 (1997).
P. Galliano, J. de Damborenea, M.J. Pascual, and A. Durán, J. Sol-Gel Sci. Technol. 13, 723 (1998).
J. Gallardo, P. Galliano, R. Moreno, and A. Durán, J. Sol-Gel Sci. Technol. 19, 107 (2000).
K. Katagiri, K. Hasegawa, and T. Minami, J. Am. Ceram. Soc. 81, 2501 (1998).
M. Mennig, G. Jonschker, and H. Schmidt, SPIE 1758, 125 (1992).
H. Schmidt, SPIE 1758, 396 (1992).
J. Gallardo, P. Galliano, A. Durán, and J.J. de Damborenea. Submitted to Corrosion Science.
O. de Sanctis and N. Pellegri, A. Durán Surface and coating Technology 70, 251–255 (1995).
H. Mohrbacher, J.-P. Celis, and J.R. Roos, Tribology International 28(5), 269 (1995).
J. Gallardo, P. Galliano, R. Moreno, and A. Durán, J. Sol-Gel. Sci. Technol. 19, 107 (2000).
J. Gallardo, P. Galliano, and A. Durán, J. Sol-Gel. Sci. Technol. 19, 393 (2000).
J. Gallardo, A. Durán, D. Di Martino, and R. M. Almeida. J. Non-Cryst. Solids 298, 219 (2002).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gallardo, J., Duran, A., Garcia, I. et al. Effect of Sintering Temperature on the Corrosion and Wear Behavior of Protective SiO2-Based Sol-Gel Coatings. Journal of Sol-Gel Science and Technology 27, 175–183 (2003). https://doi.org/10.1023/A:1023702701850
Issue Date:
DOI: https://doi.org/10.1023/A:1023702701850