Abstract
The Delivery Tunnel North starts in Lesotho and continues into South Africa. It is divided into two sections by the Caledon and Little Caledon rivers. It runs through the mudrocks and sandstones of the Tarkastad Subgroup, and the Elliot and Molteno Formations. The tunnel was excavated by a double-shield tunnel boring machine, except for the sections beneath the two rivers, which were constructed by drill and blast methods. The tunnel boring machine was selected to bore through the anticipated changing ground conditions and also was capable of installing the segmental lining of the tunnel. Boreability tests showed that the sandstones and siltstones had good boreability, but that it was very low in the dolerite dykes. At depth, the weaker mudstones presented the worst tunnelling conditions, giving rise to squeezing ground and to shear failure with accompanying overbreak. Initially a small amount of cracking occurred in the tunnel lining but this was reduced significantly as experience was gained. Cracking was observed predominantly in the weaker rock types, and this was probably associated with overbreak.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Barton, N. (1988) Rock mass classifications and tunnel reinforcement selection using the Q-system, Proceedings of the Symposium on Rock Classification for Engineering Purposes, Special Technical Publications 984, American Society for Testing Materials, Philadelphia, pp. 59–88.
Barton, N., Lien, R. and Lunde, J. (1974) Engineering Classification of Rock Masses for the Design of Tunnel Support, Publication 106, Norwegian Geotechnical Institute, Oslo.
Bieniawski, Z.T. (1974) Geomechanics classification of rock masses and its application to tunnelling, in Proceedings of the 3rd International Congress of the International Society of Rock Mechanics, Vol. 1, Denver, pp. 27–32.
Bieniawski, Z.T. (1989) Engineering Rock Mass Classifications, Wiley-Interscience, New York.
Chen J.F. and Vogler, U.W. (1992) Rock cuttability/boreability assessment research at CSIR, in Proceedings of Tuncon '92, Design and Construction of Tunnels, Maseru, South African National Council on Tunnelling, Yeoville, pp. 91–7.
Highlands Delivery Tunnel Consultants (1990) Lesotho Highlands Water Project, Delivery Tunnel North, Caledon Tunnel and Ash Tunnel Tender Document, Volumes 5.1, 5.2 and 5.6, unpublished report.
McBean, R.J. and Harries, D.A. (1970). The development of high-speed soft ground tunnelling using pre-cast concrete segments and tunnelling machines, in Proceedings South African Tunnelling Conference, Tuncon '70. The Technology and Potential of Tunnelling, Vol. 1, Cygnet Print, Johannesburg, pp. 129–34.
Parkes, D.B. (1988) The Performance of Tunnel Boring Machines in Rock, CSIR Special Publication 62, Pretoria 56p.
Richards, J.A., Remmer, F. and Sharp, J.C. (1992) Design and construction of a segmented lining for a machine bored tunnel — Delivery Tunnel North, Lesotho Highlands Water Project, Proceedings of Tuncon '92, Design and Construction of Tunnels, Maseru, South African National Council on Tunnelling, Yeoville, pp. 147–56.
Sharp, J.C. (1992) Lesotho Highlands Water Project — Delivery Tunnel North, Construction Review Report No 2, HDTC, unpublished report.
Szechy, K. (1973) The Art of Tunnelling, Academiai Kiado, Budapest.
Tarkoy, P.J. (1973) Predicting tunnel boring machine penetration rates and cutter costs in selected rock types, Proceedings of 9th Canadian Symposium on Rock Mechanics, Montreal, pp. 263–74.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
De Graaf, P., Bell, F. The Delivery Tunnel North, Lesotho Highlands Water Project. Geotechnical and Geological Engineering 15, 95–120 (1997). https://doi.org/10.1023/A:1018495121586
Issue Date:
DOI: https://doi.org/10.1023/A:1018495121586