Abstract
A new method was developed to produce tensile specimens with pre-machined holes for superplastic zirconia ceramics. Tensile specimens with effective hole sizes of 450 μm were successfully produced using graphite fibers. Although the size of the defect introduced is relatively large compared to the grain size enough deformation is obtained for qualitative and quantitative analysis for Y-TZP. 3Y-TZP and 3Y-TZP co-doped with germanium and titanium oxide revealed cavity growth coefficients that varied with strain rate and temperature, unlike metals, as a direct consequence of grain growth induced strain hardening.
Similar content being viewed by others
References
J. W. HANCOCK, Met. Sci. 10 (1976) 319.
W. BEERE and M. V. SPEIGHT, ibid. 9 (1975) 190.
Idem., ibid. 4 (1978) 172.
M. J. STOWELL, ibid. 9 (1980) 270.
A. C. F. COCKS and M. F. ASHBY, bid. 8 (1980) 395.
D. W. LIVESEY and N. RIDLEY, Met. Trans. A 13A(9) (1982) 1619.
J. BELZUNCE and M. SUERY, Acta. Metall. 31(10) (1983) 1497.
P. A. FRIEDMAN and A. K. GHOSH, Met. and Mat. Trans. 17A(12) (1996) 3827.
M. ZAKI, ibid. 27A(4) (1996) 1043.
K. KANNAN and C. H. HAMILTON, Scripta Mat. 38(2) (1998) 299.
J. R. PORTER, W. BLUMENTHAL and A. G. EVANS, Acta Met. 29 (1981) 1899.
R. L. TSAI and R. RAJ, ibid. 30 (1982) 1043.
D. J. SCHISSLER, A. H. CHOKSHI, T. G. NIEH and J. WADSWORTH, Acta Metal. Mater. 39(12) (1991) 3227.
Z. C. WANG, N. RIDLEY, T. J. DAVIES and A. A. OGWU, Acta Mat. 44(11) (1996) 4301.
Z. C. WANG, N. RIDLEY and T. J. DAVIES, Scripta Mat. 36(5) (1997) 579.
Idem., J. Mater. Sci. 34 (1999) 2695.
K. HIRAGA and K. NAKANO, Mat. Sci. Forum 243-245 (1997) 387.
K. HIRAGA, K. NAKANO, T. S. SUZUKI and Y. SAKKA, Scripta Mat. 39(9) (1998) 1273.
Idem., Mat. Sci. Forum 304-306 (1999) 431.
R. A. TAIT and D. M. R. TAIPLIN, Scripta Met. 13 (1979) 77.
D. S. WILKINSON and C. H. CACERES, Mat. Sci and Tech. 2 (1986) 1086.
H. CHOKSHI and T. G. LANGDON, Met. and Mat. Trans. A 27A (1996) 2532.
K. SASAKI, M. NAKANO, J. MIMURADA, Y. IKUHARA and T. SAKUMA, J. Am. Cer. Soc. 84(12) (2001) 2981.
G. E. DIETER, “Mechanical Metallurgy” (McGraw-Hill, New York, 1988).
F. A. MCCLINTOCK, J. App. Mech. 6 (1968) 363.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Sasaki, K., Nakano, M., Ikuhara, Y. et al. Pre-holed tensile specimens for superplastic Y-TZP ceramics. Journal of Materials Science 37, 3307–3313 (2002). https://doi.org/10.1023/A:1016199404342
Issue Date:
DOI: https://doi.org/10.1023/A:1016199404342