Abstract
Identification of all the compounds present in various coatings on steels is particularly difficult. Non-destructive, in-situ analysis is necessary if the fraction of each compound as well as its probable layering within the coating, is to be determined. Mössbauer spectroscopy is one valuable probe capable of uniquely identifying all iron compounds which form as coatings on steel and other iron alloy surfaces. To investigate a complete coating several criteria need to be considered. Removing the coating inevitably leaves a small and perhaps important component intact on the substrate. Therefore investigating the coating as it remains intact on the steel is important if complete identification of the iron compounds is to be made. This also preserves crystalline texture or preferred growth orientation within the coating to which the Mössbauer effect is sensitive. Mössbauer spectroscopy is a non-destructive technique which allows the integrity of the coating to be maintained during analysis. The combined transmission and scattering Mössbauer geometries generally result in accurate analysis of the coating composition. For the scattering geometry added information on compound layering is obtained if separate Mössbauer spectra are recorded using the re-emitted gamma rays as well as the conversion electrons and subsequently emitted X-rays.
In-situ scattering Mössbauer spectroscopy has been used to characterize the iron--zinc alloys which form in the coatings of commercially produced corrosion resistant galvannealed sheet steel, a product of great interest to automotive producers. The results show that different amounts of four iron--zinc phases are present depending on the production conditions of the coating. The different phases are also distinctly layered.
Mössbauer analyses of corrosion coatings formed on the surface of steels which have been exposed to different environments has also been undertaken. Materials include structural steels exposed for up to 25 years in marine, rural and industrial environments, and the interior surfaces of boiler pipes subjected to adverse chemical and temperature environments.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
D.C. Cook and R.G. Grant, Mössbauer Spectroscopy Applied to Magnetism and Materials Science, Vol. 2, eds. G.J. Long and F. Grandjean (Plenum, NY, 1966) Ch. 10. pp. 225–271.
H.E. Townsend, L. Allegra, R.J. Dutton and S.A. Kriner, Materials Performance 25(8) (1986) 36–46.
H.E. Townsend, The NACE Annual Conference and Corrosion Show, paper #416 (1991).
Y. Suemitsu, in: Proc. Galvatech'95: The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Iron and Steel Society, C.E. Slater Publ., 1995) pp. 3–12.
T. Hada, in: Proc. Galvatech'95: The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Iron and Steel Society, C.E. Slater Publ., 1995) pp. 217–224.
J.S. Kim and J.H. Chung, in: Proc. Galvatech'95: The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Iron and Steel Society, C.E. Slater Publ., 1995) pp. 135–138.
O. Kubaschewski, Iron — Binary Phase Diagrams (Springer-Verlag, 1982) pp. 86–87.
B. Dauby, P. Vamkeleffe and S. Feron, in: Proc. Galvatech'95: The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Iron and Steel Society C.E. Slater Publ., 1995) pp. 717–722.
G.J. Harvey and P.N. Richards, Met. Forum 6(4) (1984) 232.
H. Smith and W. Batz, JISI (1972) 895.
D.C. Cook, Mössbauer Effect Study of Four Metal Powder Galvanneal Standards, Bethlehem Steel Corporation Report #ODUDCC0191 (1991).
D.C. Cook, Mössbauer Analysis of the Zinc—Iron Phases on Galvannealed Steel, Bethlehem Steel Corporation Report #ODUDCC0289 (1989).
M. Gu, M.R. Notis and A.R. Marder, Metallurgical Transactions A 21 (1990) 273–277.
D.C. Cook, R.S. Tuszynski and H.E. Townsend, Hyperfine Interactions 54 (1990) 781–785.
D.C. Cook and R.G. Grant, Identification of the Iron—Zinc Phases in Galvanneal Steel Coatings by Mössbauer Spectroscopy and X-Ray Diffraction. Phase I: Characterization of the Fe-Zn Intermetallic Phases. International Lead Zinc Research Organization Report #ODUDCC0193 (1993).
R.G. Grant and D.C. Cook, Hyperfine Interactions 94 (1994) 2309.
D.C. Cook and R.G. Grant, in: Proc. Galvatech'95: The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Iron and Steel Society, C.E. Slater Publ., 1995) pp. 497–508.
R.G. Grant and D.C. Cook, in: Proceedings ICAME'95 (Italian Physical Society, 1996) p. 929.
D.C. Cook and R.G. Grant, Identification of the Iron-Zinc Phases in Galvanneal Steel Coatings by Mössbauer Spectroscopy and X-Ray Diffraction. Phase II: Construction and Testing of a Coating Analyzer, ILZRO, Inc. Report #ODUDCC0294 (1994).
R.G. Grant and D.C. Cook, in: Proc. Galvatech'95: The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Iron and Steel Society, C.E. Slater Publ., 1995) pp. 509–514.
S.J. Oh, D.C. Cook and A.C. Van Orden, Iron Oxide Analysis on the Interior Surfaces of Four Boiler Tubes, Report # ODUDCC0395 submitted to Ashland Chemical Company (1995).
S.J. Oh, D.C. Cook and H.E. Townsend, Submitted for publication to Hyperfine Interactions in November 1996.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Cook, D.C. In-situ identification of iron--zinc intermetallics in galvannealed steel coatings and iron oxides on exposed steel. Hyperfine Interactions 111, 71–82 (1998). https://doi.org/10.1023/A:1012629028199
Issue Date:
DOI: https://doi.org/10.1023/A:1012629028199