Abstract
The effect of test environment on the creep behavior of a poly(ethylmethacrylate) bone cement was investigated. The aim of the study was to assess the influence of environment on the inherent material behavior, and so it was convenient to perform tests in tension on well-prepared samples. In addition to control tests in air, the liquid environments studied were water, Ringer's solution and Intralipid. Creep tests were performed in each of these environments with a range of aging times, test temperatures and applied stresses. In order to compare the effects of the environments, the creep curves were fitted to a generalized form, from which a creep rate was determined. The ratio of these creep rates between different environments at each testing condition was then used as a basis for a comparison of the detailed effects of environment.
It was found that in all cases the water-based environments (water and Ringer's) had similar effects and gave the largest creep rates. Intralipid was then intermediate and air gave the lowest creep rates. These effects are mainly due to plasticization by water, although with Intralipid, some increased monomer leaching occurred, which served to reduce the creep rates. The influence of environment on the effects of aging time, temperature and stress were complex, although in general any conditions which increased water plasticization (longer aging, higher temperature and to a lesser extent, higher stress) gave an increase in creep rate. The major exception to this was at temperatures of 40 °C and above, where the effects of water plasticization were diminished, due to the inherent increase in molecular mobility of the material.
© 2001 Kluwer Academic Publishers
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
J. Charnley, in “Acrylic Cement in Orthopaedic Surgery” (Churchill Livingstone, London, 1972).
A. Gruen, G. M. Mcneice and H. C. Amustutz, Clin. Orthop. Rel. Res. 141 (1979) 17.
D. K. Collis, J. Bone Joint Surg. 73A (1991) 593.
J. H. Boss, I. Shajrawi, S. Dekel and D. G. Mendes, J. Biomat. Sci. Poly. Ed. 5(3) (1993) 221.
R. P. Kusy, J. Biomed. Mater. Res. 12 (1978) 271.
B. Weightman, M. A. R. Freeman, P. A. Revell, M. Braden, B. E. Albrektsson and L. V. Carlson, J. Bone Joint Surg. 69B (1987) 558.
G. M. Brauer, D. R. Steinberger and J. W. Stansbury, J. Biomed. Mat. Res. 20 (1986) 839.
K. W. Davy and M. Braden, Biomaterials 12 (1991) 540.
P. A. Revell, M. George, M. Braden, M. Freeman and B. Weightman J. Mat. Sci. Mat. Med. 3 (1992) 84.
P. A. Revell, M. Braden, B. Weightman and M. Freeman Clin. Mats. 10 (1992) 233.
J. C. Behiri, M. Braden, S. N. Khorasani, D. Wiwattandate and W. Bonfield Bioceramics 4 (1991) 301.
E. J. Harper, J. C. Behiri and W. Bonfield J. Mat. Sci. Mat. Med. 6 (1995) 799.
J. L. Hailey, I. G. Turner and A. W. Miles J. Mat. Sci. Mat. Med. 6 (1995) 635.
L. C. E. Struik, in “Physical Aging in Amorphous Polymers and Other Materials” (Elsevier, Amsterdam, 1978).
ASTM F451-86 American Society for Testing and Materials, (Philadelphia, PA, 1986).
J. J. Aklonis and W. J. Knight, in “Introduction to Polymer Viscoelasticity” (Wiley, New York, 1983).
P. S. Theocaris, G. C. Papanocolaov and E. A. Kontow J. Polym. Sci. 28 (1983) 3145.
G. C. Papanocolaov and R. Mercoliano Plast. Rubb. Proc. Appln. 6 (1986) 229.
J. L. Hailey, I. G. Turner A. W. Miles and G. Price J. Mat. Sci. Mat. Med. 5 (1994) 617.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Arnold, J.C., Venditti, N.P. Effects of environment on the creep properties of a poly(ethylmethacrylate) based bone cement. Journal of Materials Science: Materials in Medicine 12, 707–717 (2001). https://doi.org/10.1023/A:1011272626846
Issue Date:
DOI: https://doi.org/10.1023/A:1011272626846