Abstract
The microstructural evolutions and mechanical properties of vanadium microalloyed steel (30MSV6) during precipitation hardening were studied. The effects of aging temperature and cooling rate on mechanical strength (yield strength and ultimate tensile strength) were similar. Increasing aging temperature or cooling rate firstly increased the mechanical strength of specimens up to their maximum values, which then decreased with further increase in aging temperature or cooling rate. Microstructural evolutions revealed that cooling rate had significant effects on the pearli-te interlamellar spacing and size of pre-eutectoid ferrite. Unlike the effect of austenitizing temperature, the pearlite interlamellar spacing and pre-eutectoid ferrite size were decreased by increasing the cooling rate from austenitizing temperature. According to the microstructural evolutions and mechanical properties, the optimal heat treatment process of microalloyed steel 30MSV6 was austenitizing at 950 °C for 1 h, air cooling (3. 8 °C/s) and aging at 600 °C for 1.5 h. This optimal heat treatment process resulted in a good combination of elongation and yield strength.
Similar content being viewed by others
References
Demir H. The Effects of Microalloyed Steel Pre-Heat Treatment on Microstructure and Machinability [J]. International Journal of Advanced Manufacturing Technology, 2008, 35(9/10): 1041.
Gunduz S, Capar A. Influence of Forging and Cooling Rate on Microstructure and Properties of Medium Carbon Microalloy Forging Steel [J]. Journal of Materials Science, 2006, 41(2): 561.
Gunduz S, Acarer M. The Effect of Heat Treatment on High Temperature Mechanical Properties of Microalloyed Medium Carbon Steel [J]. Materials and Design, 2006, 27(10): 1076.
Militzer M, Hawbolt E B, Meadowcroft T R. Microstructural Model for Hot Strip Rolling of High-Strength Low-Alloy Steels [J]. Metallurgical and Materials Transactions, 2000, 31A(4): 1247.
Chun X, Sun Q, Chen X. Research on Transformation Mechanism and Microstructure Evolution Rule of Vanadium-Nitrogen Microalloyed Steels [J]. Materials and Design, 2007, 28(9): 2523.
André Barros Cota, Fernando Lucas Gonçalves e Oliveira, Anderson Luiz da Rocha e Barbosa, et al. Microstructural and Mechanical Properties of a Microalloyed Steel After Thermal Treatment [J]. Materials Research, 2003, 6(2). 117.
Adamczyk J. Development of the Microalloyed Constructional Steels [J]. Journal of Achievements in Materials and Manufacturing Engineering, 2006, 14(1/2): 9.
LIU Sheng-xin, CHEN Yong, LIU Guo-quan, et al. Effect of Intermediate Cooling on Precipitation Behavior and Austenite Decomposition of V-Ti-N Steel for Non-Quenched and Tempered Oil-Well Tubes [J]. Materials Science and Engineering, 2008, 485A(1/2): 492.
Dhua S K, Mukerjee D, Sarma D S. Influence of Tempering on the Microstructure and Mechanical Properties of HSLA-100 Steel Plates [J]. Metallurgical and Materials Transactions, 2001, 32A(9): 2259.
Joseph R Davis. Alloying: Understanding the Basics [M]. Oh: ASM International, 2001.
Gunduz S, Cochrane R C. Influence of Cooling Rate and Tempering on Precipitation and Hardness of Vanadium Microalloyed Steel [J]. Materials and Design, 2005, 26(6): 486.
Lagneborg R, Siwecki T, Zajac S, et al. The Role of Vanadium in Microalloyed Steels [M] // Swedish Institute for Metals Research. Stockholm: The Scandanavian Journal of Metallurgy, 1999.
CAO Jian-chun, YONG Qi-long, LIU Qing-you, et al. Precipitation of MC Phase and Precipitation Strengthening in Hot Rolled Nb-Mo and Nb-Ti Steels [J]. Journal of Materials Science, 2007, 42(24): 10080.
Najafi H, Rassizadehghani J, Asgari S. As-Cast Mechanical Properties of Vanadium/Niobium Microalloyed Steels [J]. Materials Science and Engineering, 2008, 486A(1/2): 1.
Jahazi M, Eghbali B. The Influence of Hot Forging Conditions on the Microstructure and Mechanical Properties of Two Microalloyed Steels [J]. Journal of Materials Processing Technology, 2001, 113(1/2/3): 594.
Standard Test Method for Tension Testing of Metallic Materials. ASTM E8/E8M-11 [S]. PA: ASTM International, 2011.
Andrews K W. Empirical Formulae for the Calculation of Some Transformation Temperatures [J]. JISI, 1965, 203: 721
Gladman T, Pickering F B, Baker T N. Yield, Flow and Fracture of Polycrystals [M]. London: Applied Science Publishers, 1983.
Elwazri A M, Wanjara P, Yue S. The Effect of Microstructural Characteristics of Pearlite on the Mechanical Properties of Hypereutectoid Steel [J]. Materials Science and Engineering, 2005, 404A(1/2): 91.
Marshall P. Development of Microstructure to Optimize Mechanical Performance of Power Generation Equipment [C] // Bramfitt B L, Benn R C, Brinkman C R, et al. MiCon 86: Optimization of Processing, Properties, and Service Performance Through Microstructural Control. Philadelphia; American Society for Testing and Materials, 1988: 3.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hajisafari, M., Nategh, S., Yoozbashizadeh, H. et al. Improvement in Mechanical Properties of Microalloyed Steel 30MSV6 by a Precipitation Hardening Process. J. Iron Steel Res. Int. 20, 66–73 (2013). https://doi.org/10.1016/S1006-706X(13)60100-4
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S1006-706X(13)60100-4