Abstract
Non-uniformity of temperature distribution across strip width direction is the ultimate reason why the flatness defect occurs on the strip after cooling process although the strip is flat at the exit of finishing mill. One thermal, microstructural and mechanical coupling analysis model for predicting flatness change of steel strip during the run-out table cooling process was established using ABAQUS finite element software. K Esaka phase transformation kinetics model was employed to calculate the phase transformation, and coupled with temperature calculation using the user subroutine program HETVAL. Elasto-plasticity constitutive equations of steel material, in which conventional elastic and plastic strains, thermal strain, phase transformation strain and transformation induced plastic strain were considered, were derived and programmed in the user subroutine program UM AT. The conclusion that flatness of steel strip will develop to edge wave defect under the functions of the differential thermal and microstructural behaviors across strip width during the run-out table cooling procedure was acquired through the analysis results of this model. Calculation results of this analysis model agree well with the actual measurements and observation.
Similar content being viewed by others
References
LIU Zheng-dong. Experiments and Mathematical Modeling of Controlled Runout Table Cooling in a Hot Rolling Mill [D]. Vancouyer; The University of British Columbia, 2001 (in Chinese).
Serajzadeh S. Prediction of Temperature Distribution and Phase Transformation on the Run-Out Table in the Process of Hot Strip Rolling [J]. Applied Mathematical Modelling, 2003, 27 (2): 861.
Yoshida H. Analysis of Flatness of Hot Rolled Steel Strip After Cooling [J]. Transactions ISU, 1984, 24(3): 212.
Wang Shyi-chin, Chiù Fon-jen, Ho Tsan-ying. Characteristics and Prevention of Thermomechanical Controlled Process Plate Deflection Resulting From Uneven Cooling [J]. Materials Science and Technology, 1996, 12(1): 64.
CAI Zheng. Research on Buckling Behavior of Hot-Rolled Strip After Cooling [D]. Shenyang; Northeastern University, 1998 (in Chinese).
Han H N, Lee J K, Kim H J, et al. A Model for Deformation, Temperature and Phase Transformation Behavior of Steels on Run-Out Table in Hot Strip Mill [J]. Journal of Materials Processing Technology, 2002, 128: 216.
Colas R, Leduc L A, Neri M A. Prediction of Shape Defects During Cooling of Hot Rolled Low Carbon Steel Strip [J]. Ironmaking and Steelmaking, 2004, 31(1): 93.
Zhou Zhong-qing, Thomson P F, Lam Y, et al. Numerical Analysis of Residual Stress in Hot-Rolled Steel Strip on the Run-Out Table [J], Journal of Materials Processing Technology, 2003, 132: 184.
Ogai H, Ito M, Hirayama R. Consistent Shape Prediction Simulator After Hot Rolling Mill [J]. Nippon Steel Technical Report, 2004, 89: 43.
ZHOU Zhong-qing, Lam Y, Thomson P F, et al. Numerical Analysis of the Flatness of Thin, Rolled Steel Strip on the Runout Table [J]. Proceedings of the Institution of Mechanical Engineers, Part B; Journal of Engineering Manufacture, 2007, 221(2): 241.
Nikitenko E, Gris B C. A Mechanism of Post-Rolling Deterioration in Hot Band Flatness During Coiling [J]. Iron and Steel Technology, 2009, 6(10): 60.
Pacheco P M C L, Savi M A, Camarào A F. Analysis of Residual Stresses Generated by Progressive Induction Hardening of Steel Cylinders [J]. Journal of Strain Analysis, 2001, 36 (5): 507.
Yao Xin, Zhu LH, Li M Victor. Finite Element Analysis of Residual Stress and Distortion in an Eccentric Ring Induced by Quenching [J]. Transactions of Materials and Heat Treatment Proceedings of the 14th IFHTSE Congress, 2004, 25 (5); 746.
Silva E P, Pacheco P M C L, Savi M A. Finite Element Analysis of the Phase Transformation Effect in Residual Stresses Generated by Quenching in Notched Steel Cylinders [J]. Journal of Strain Analysis, 2005, 40(2): 151.
Casotto S, Pascon F, Habraken A M, et al. Thermo-Mechanical-Metallurgical Model to Predict Geometrical Distortions of Rings During Cooling Phase After Ring Rolling Operations [J]. International Journal of Machine Tools and Manufacture, 2005, 45: 657.
Kwon O. A Technology for Prediction and Control of Microstructural Changes and Mechanical Properties in Steel [J]. ISIJ International, 1992, 32(3): 350.
Taleb L, Sidoro F. A Micromechanical Modeling of the Greenwood-Johnson Mechanism in Transformation Induced Plasticity [J]. International Journal of Plasticity, 2003, 19: 1821.
ABAQUS Standard Version 6. 5. User Manual, Theory Manual [M]. Michigan; Hibbitt, Karlsson and Sorensen, Ine, 2005.
Becker M, Jordan C, Lachhander S K, et al. Prediction and Measurement of Phase Transformations, Phase-Dependent Properties and Residual Stresses in Steels [C]//Proceedings of the 7th International Conference on Trends in Welding Research. Callaway Gardens Resort, Pine Mountain, Georgia, USA, 2005: 1007.
Wang Xiao-dong, Yang Quan, He An-rui. Calculation of Thermal Stress Affecting Strip Flatness Change During RunOut Table Cooling in Hot Steel Strip Rolling [J]. Journal of Materials Processing Technology, 2008, 207: 130.
ZHANG Mai-cang, DONG Jian-xin, ZENG Yan-ping, et al. Dynamical Microstructure Evolution of Q235 Low Carbon Steel During High Temperature Deformation [J]. Journal of University of Science and Technology Beijing, 2005, 27(2):183 (in Chinese).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, Xd., Li, F. & Jiang, Zy. Thermal, Microstructural and Mechanical Coupling Analysis Model for Flatness Change Prediction During Run-Out Table Cooling in Hot Strip Rolling. J. Iron Steel Res. Int. 19, 43–51 (2012). https://doi.org/10.1016/S1006-706X(13)60007-2
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S1006-706X(13)60007-2