Abstract
The quantitative analysis of substructure in the martensite/bainite mixed structure, which is obtained from low-carbon NiCrMoV steels under different cooling conditions, was made by means of optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM), in order to research the effect on toughness. The test results indicate that the toughness of the steel is enhanced with the decrease in the packet and block size under the condition of the same prior austenite grain size mixed with different ratios of martensite and bainite while the lath width is about 0.38 µm. The calculation shows that both the packet and block boundaries have the same hindering effect on crack extension. Furthermore, the effect of the block width on impact energy is much larger than that of the packet. Therefore, the block can be used as microstructural substructure to affect the toughness in low-carbon martensite steels, suggesting that the block size is “the effective grain size” for controlling toughness.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
YAO Zhong-kai. Structural Transformation of Steel [M]. Beijing: Mechanical Industry Press, 1980 (in Chinese).
Maki T, Tsuzaki K, Tamura I. The Morphology of Micro-structure Composed of Lath Martensites in Steels [J]. Transactions ISIJ (Transactions the Iron and Steel Institute of Japan), 1980, 20(4): 207.
Morito S, Tanaka H, Konishi R, et al. The Morphology and Crystallography of Lath Martensite in Fe-C Alloys [J]. Acta Materialia, 2003, 51(6): 1789.
Swarr T, Krauss G. The Effect of Structure on the Deformation of As-Quenched and Tempered Martensite in an Fe-0. 2pct C Alloy [J]. Metallurgical Transactions, 1976, 7A(1): 41.
Morito S, Yoshida H, Maki T, et al. Effect of Block Size on the Strength of Lath Martensite in Low Carbon Steels [J]. Materials Science and Engineering, 2006, 438–440A: 237.
Tomita Y, Okabayashi K. Effect of Microstructure on Strength and Toughness of Heat-Treated Low Alloy Structural Steels [J]. Metallurgical Transactions, 1986, 17A(7): 1203.
WANG Chun-fang, WANG Mao-qiu, SHI Jie, et al. Effect of Microstructure on the Toughness of Low Alloy Martensitic Steel [J]. Scripta Materialia, 2008, 58(6): 492–495.
Inoue T, Matsuda S, Okamura Y, et al. The Fracture of a Low Carbon Tempered Martensite [J]. Transactions of JIM, 1970, 11(1): 36.
LePera F S. Improved Etching Technique to Emphasize Martensite and Bainite in High-Strength Dual-Phase Steel [J]. J Metall, 1980, 32: 38.
Girault E, Jacques P, Harlet Ph, et al. Metallographic Methods for Revealing the Multiphase Microstructure of TRIP-Assisted Steels [J]. Materials Characteristic, 1998, 40(2): 111.
SHI Xue-xing. Effect of Critical Heat Treatment on Micro-structure and Properties in 5NiCrMo Steel [D]. Kunming: Kunming University of Science and Technology, 2008 (in Chinese).
Bouyne E, Flower H M, Lindley T C, et al. Use of EBSD Technology to Examine Microstructure and Cracking in a Bainitic Steel [J]. Scripta Materialia, 1998, 39(3): 295.
Ayer R, Mueller R R, Neeraj T. Electron Backscattered Diffraction Study of Cleavage Fracture in Pure Iron [J]. Materials Science and Engineering, 2006, 417A(1/2): 243.
Hanamura T, Yin F, Nagai K. Ductile-Brittle Transition Temperature of Ultrafine Ferrite/Cementite Microstructure in a Low Carbon Steel Controlled by Effective Grain Size [J]. ISIJ International, 2004, 44(3): 610.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Luo, Zj., Shen, Jc., Su, H. et al. Effect of Substructure on Toughness of Lath Martensite/Bainite Mixed Structure in Low-Carbon Steels. J. Iron Steel Res. Int. 17, 40–48 (2010). https://doi.org/10.1016/S1006-706X(10)60168-9
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S1006-706X(10)60168-9