Acta Mechanica Solida Sinica

, Volume 24, Issue 6, pp 539–555 | Cite as

The Analysis of Interlaminar Stresses for Composite Laminated Shallow Shells with Interfacial Damage

Article

Abstract

Based on the general six-degrees-of-freedom plate theory towards the accurate stress analysis and nonlinear theory of shallow shells, considering the damage effect of the interlaminar interface and using the variation principle, the three-dimensional non-linear equilibrium differential equations of the laminated shallow shells with interfacial damage are derived. Then, considering a simply supported laminated shallow shell with damage and under normal load, an analytical solution is presented by using finite difference method to obtain the interlaminar stresses. Numerical results show, the stiffness of the shell is weakened, greater absolute values of displacements as well as smaller interlaminar stresses are obtained by interfacial damage. When the interfacial damage is further increased, delamination occurs obviously under normal pulling load and pure shear slip occurs under normal pressure load. The portion of the load undertaken by the two sides of the interface is more different. Different mechanical behaviors are shown in both sides of the interface, and the discontinuation of stresses and displacements takes place in the interface.

Key words

laminated shallow shells geometric nonlinearity accurate stress analysis interfacial damage inter-laminar stresses 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    You, X.M., Zhao, H.F. and Wei, Y.G., Determination of interfacial mechanical parameters Foranal/Epoxy/Al2O3 system by using peel test simulations. Acta Mechanica Solida Sinica, 2008, 20(3): 198–206.CrossRefGoogle Scholar
  2. [2]
    Zakaria, K., Sirwah, M.A. and Assaf, A., Magnetohydrodynamics instability of interfacial waves between two immiscible incompressible cylindrical fluids. Acta Mechanica Sinica, 2008, 24: 497–514.MathSciNetCrossRefGoogle Scholar
  3. [3]
    Needleman, A., A continuum model for void nucleation by inclusion debonding. Journal of Applied Mechanics, 1987, 54(3): 525–531.CrossRefGoogle Scholar
  4. [4]
    Needleman, A., An analysis of decohersion along an imperfect interface. Interational Journal of Fracture, 1990, 42(1): 21–40.CrossRefGoogle Scholar
  5. [5]
    Toledano, A. and Murakami, H., Shear-deformable two-layer plate theory with interlayer slip. ASCE Journal of Engineering Mechanics Division, 1988, 144(4): 604–623.CrossRefGoogle Scholar
  6. [6]
    Soldatos, K.P. and Watson, P., A general four-degrees-of-freedom theory suitable for the accurate stress analysis of homogeneous and laminated composite beams. International Journal of Solids and Structures, 1997, 34(22): 2857–2885.CrossRefGoogle Scholar
  7. [7]
    Soldatos, K.P. and Watson, P., A method for improving the stress analysis performance of one- and two-dimensional theories for laminated composites. Acta Mechanica, 1997, 123(3): 163–186.CrossRefGoogle Scholar
  8. [8]
    Soldatos, K.P. and Watson, P., Accurate stress analysis of laminated plates combining a two-dimensional theory with the exact three-dimensional solution for simply supported edges. Mathematics and Mechanics of Solids, 1997, 2(4): 459–489.MathSciNetCrossRefGoogle Scholar
  9. [9]
    Shu, X.P., A generalized model of laminated composite plates with interfacial damage. Composite Structure, 2006, 74: 237–246.CrossRefGoogle Scholar
  10. [10]
    Kim, G.W. and Lee, K.Y., Influence of weak interfaces on buckling of orthotropic rectangular laminates. Composite Structure, 2007, 81: 427–431.CrossRefGoogle Scholar
  11. [11]
    Kim, G.W. and Lee, K.Y., Optimization of orthotropic rectangular laminates with weak interfaces under buckling. Composites: Part A: Applied Science and Manufacturing, 2007, 38: 265–271.CrossRefGoogle Scholar
  12. [12]
    Barbero, E.J. and Reddy, J.N., Modeling of delamination in composite laminates using a layer-wise plate theory. International Journal of Solids and Structures, 1991, 28(3): 373–388.CrossRefGoogle Scholar
  13. [13]
    Point, N. and Sacco, E., Delamination of deams: an application of the DCB specimen. International Journal of Fracture, 1996, 79: 225–247.CrossRefGoogle Scholar
  14. [14]
    Fu, Y.M., Li, S. and Jiang, Y.J., A constitutive model for composite laminated plates with the damage effect of the intra-layers and inter-laminar interface is presented. Acta Mechanica Solida Sinica, 2008, 2(2): 127–140.CrossRefGoogle Scholar
  15. [15]
    Shu, X.P. and Kostas, P.S., An accurate de-lamination model for weakly bonded laminates subjected to different set of edge boundary conditions. International Journal of Mechanical Sciences, 2001, 43: 935–959.CrossRefGoogle Scholar
  16. [16]
    Kostas, P.S. and Shu, X.P., Modeling of perfectly and weakly bonded laminated plates and shallow shells. Composites science and technology, 2001, 61: 247–260.CrossRefGoogle Scholar
  17. [17]
    Kostas, P.S. and Shu, X.P., On the stress analysis of cross-ply laminated plates and shallow shell panels. Composite structures, 1999, 26: 333–344.Google Scholar
  18. [18]
    Huang, N.N., Influence of shear correction factors in the higher-order shear deformation of laminated shell theory. International Journal of Solids Structure, 1994, 31: 1263–1277.CrossRefGoogle Scholar

Copyright information

© The Chinese Society of Theoretical and Applied Mechanics and Technology 2011

Authors and Affiliations

  1. 1.College of Mechanics and AerospaceHunan UniversityChangshaChina

Personalised recommendations