Advertisement

Linear integral analysis of bar rough rolling by strain rate vector

  • Wei Deng
  • De-wen Zhao
  • Xiao-mei Qin
  • Xiu-hua Gao
  • Lin-xiu Du
  • Xiang-hua Liu
Article

Abstract

A new linear integral method for bar hot rolling on roughing train was obtained. First, for plastic deformation energy rate, equivalent strain rate about Kobayashi s three-dimensional velocity field was expressed by two-dimensional strain rate vector; then, the two-dimensional strain rate vector was inverted into inner product and was integrated term by term. During those processes, boundary equation and mean value theorem were introduced; for friction and shear energy dissipation rate, definite integral was applied to the solution process. Sequentially, the total upper bound power was minimized, and the analytical expressions of rolling torque, separating force, and stress state factor were obtained. The calculated results by these expressions were compared with those of experimental values. The results show that the new linear integral method is available for bar rough rolling analysis and the calculated results by this method are a little higher than those of experimental ones. However, the maximum error between them is less than 10%.

Key words

bar rough rolling linear integration strain rate vector roll separating force 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    Khaikin B E, Kisilenko I A, Tranovskii I Y. Pressure of Metal on Rolls in Section Rolling [J]. Steel USSR, 1971(1): 884.Google Scholar
  2. [2]
    Arnold R R, Whitton P W. Spread and Roll Force in Rod Rolling [J]. Metal Tech, 1975(2): 143.Google Scholar
  3. [3]
    Shinokura T, Takai K. Mathematical Models of Roll Force and Torque in Steel Bar Rolling [J]. Tetsu-to-Hagane, 1986, 72(14): 1870 (in Japanese).CrossRefGoogle Scholar
  4. [4]
    Ahmed Said, Lenard J G, Ragab A R, et al. The Temperature, Roll Force and Roll Torque During Hot Bar Rolling [J]. J Mater Process Technol, 1999, 88(1–3): 147.Google Scholar
  5. [5]
    Oh S I, Kobayashi S. An Approximate Method for a Three-Dimensional Analysis of Rolling [J]. Int J Mech Sci, 1975, 17 (4): 295.CrossRefGoogle Scholar
  6. [6]
    Kazunori K, Tadao M, Toshihiko K. Flat-Rolling of Rigid-Perfectly Plastic Solid Bar by the Energy Method [J]. J Jap Soc Tech Plasticity, 1980, 21(231): 359 (in Japanese).Google Scholar
  7. [7]
    Pittman J F T, Zienkiewicz O C, Wood R D, et al. Numerical Analysis of Forming Processes [M]. New York: John Wiley and Sons Ltd, 1984.MATHGoogle Scholar
  8. [8]
    Kim N, Lee S M, Shin W, et al. Simulation of Square-to-Oval Single Pass Rolling Using a Computationally Effective Finite and Slab Element Method [J]. J Eng Ind, 1992(114): 329.Google Scholar
  9. [9]
    Park J J, Oh S I. Application of Three Dimensional Finite Element Analysis to Shape Rolling Processes [J]. J Eng Ind, 1990 (112): 36.Google Scholar
  10. [10]
    Kim N, Kobayashi S, Altan T. Three-Dimensional Simulation of Gap Controlled Plate Rolling by the Finite Element Method [J]. Int J Mach Tolls Manuf, 1990, 30(2): 269.CrossRefGoogle Scholar
  11. [11]
    Montmitonnet P, Chenot J L, Bertrand-Corsini C, et al. A Coupled Themomechanical Approach for Hot Rolling by a 3D Finite Element Method [J]. J Eng Ind, 1992(114): 336.Google Scholar
  12. [12]
    LI Chang-cheng, REN Yu-hui, ZHANG Li-fen, et al. Measurement and Study on ϕ500 mm Rougher Mill of High Speed Untwist Rod Mill [J]. Iron and Steel, 2002, 37(2): 59 (in Chinese).Google Scholar
  13. [13]
    ZHAO De-wen, WANG Guo-dong, BAI Guang-run. Theoretical Analysis of the Wire Drawing Through Two Roller Dies in Tandem [J]. Science in China; Series A, 1993, 36 (5): 632.Google Scholar
  14. [14]
    WANG Guo-dong, ZHAO De-wen. Modern Materiel Forming Mechanics [M]. Shenyang: Northeastern University Press, 2004 (in Chinese).Google Scholar
  15. [15]
    ZHAO De-wen. Mathematical Solution of Continuum Forming Force [M]. Shenyang: Northeastern University Press, 2003 (in Chinese).Google Scholar
  16. [16]
    ZHAO De-wen, GUO Chang-wu, LIU Xiang-hua. Surface Integral of Three-Dimensional Velocity Field for Square Bar Drawing Through Conical Die [J]. Trans Nonferrous Met Soc China, 1996, 6(3): 131.Google Scholar
  17. [17]
    ZHAO De-wen, XIE Ying-jie, LIU Xiang-hua, et al. Three-Dimensional Analysis of Rolling by Twin Shear Stress Yield Criterion [J]. Journal of Iron and Steel Research, International, 2006, 13(6): 21.CrossRefGoogle Scholar
  18. [18]
    ZHAO Zhi-ye. Metal Forming Mechanics [M]. Beijing: Metallurgical Industry Press, 1987 (in Chinese).Google Scholar
  19. [19]
    ZHAO Ji-hua, GUAN Ke-zhi. Resistance of Metal Plastic Deformation [M]. Beijing: Mechanical Industry Press, 1989 (in Chinese).Google Scholar

Copyright information

© China Iron and Steel Research Institute Group 2010

Authors and Affiliations

  • Wei Deng
    • 1
  • De-wen Zhao
    • 1
  • Xiao-mei Qin
    • 1
  • Xiu-hua Gao
    • 1
  • Lin-xiu Du
    • 1
  • Xiang-hua Liu
    • 1
  1. 1.State Key Laboratory of Rolling and AutomationNortheastern UniversityShenyang, LiaoningChina

Personalised recommendations