Abstract
An unqualified six-cylinder heavy truck crankshaft has been studied to investigate the cause of magnetic particle testing defects on the rod journals. Large-sized long-striped MnS inclusions are regarded as the major cause for the magnetic particle testing failure because they have been detected in situ under the magnetic particle indications. Through the observation of macroscopic structures of the rod journals and corresponding counterweight blocks, it is found that for the 1# and 3# rod journals, the center metal of the original hot-rolled bar has been extruded to the inboard edge of the rod journals and large-sized long-striped MnS inclusions are exposed on the surface after flash removal, leading to the failure of magnetic particle testing. As for the 2# rod journal, the center metal of the original bar has not been extruded to the surface and MnS inclusions on the rod journal surface are small in size, few in number, resulting in passing the magnetic particle testing. If the quality of the hot-rolled bars fluctuates, it is more recommended to apply magnetic particle testing on samples at the center of bars before forging to evaluate the severity of defects caused by the long-striped MnS inclusions for fear of the scrap of the final crankshafts.
Similar content being viewed by others
References
L.M. Alves, P.A.F. Martins, J. Mater. Process. Technol. 211 (2011) 467–474.
F. Zhao, M. Wu, B. Jiang, C. Zhang, J. Xie, Y. Liu, Mater. Sci. Eng. A 731 (2018) 360–368.
W. Hui, Y. Zhang, C. Shao, S. Chen, X. Zhao, H. Dong, Mater. Sci. Eng. A 640 (2015) 147–153.
B. Jiang, Z. Dong, Z. Yang, L. Zhou, Y. Liu, Y. Wang, Trans. Indian Inst. Met. 68 (2015) 553–559.
X. Xu, Z. Yu, Z. Yang, J. Fail. Anal. Prev. 11 (2011) 51–55.
H. Kanisawa, T. Ochi, Nippon Steel Tech. Rep. 81 (2000) 22–28.
V. Ollilainen, H. Hurmola, H. Pöntinen, J. Mater. Energy Syst. 5 (1984) 222–232.
T. Furuhara, J. Yamaguchi, N. Sugita, G. Miyamoto, T. Maki, ISIJ Int. 43 (2003) 1630–1639.
B. Jiang, M. Wu, H. Sun, Z. Wang, Z. Zhao, Y. Liu, Met. Mater. Int. 24 (2018) 15–22.
R. Qi, M. Jin, X. Liu, B. Guo, J. Iron Steel Res. Int. 23 (2016) 531–538.
Z. Yang, Y. Liu, L. Zhou, G. Li, D. Zhang, Adv. Mater. Res. 311 (2011) 1648–1652.
A. Li, S. Luo, Forging and Stamping Technology 40 (2015) 11–20.
Y. Ito, N. Masumitsu, K. Matsubara, Trans. Iron Steel Inst. Jpn. 21 (1981) 477–484.
J. Xie, D. Hu, J. Fu, H. Liu, Ironmak. Steelmak. 46 (2019) 542–549.
Y. Luo, J. Zhang, Z. Liu, C. Xiao, S. Wu, Acta Metall. Sin. (Engl. Lett.) 24 (2011) 326–334.
J. Lu, G. Cheng, B. Tan, J. Che, ISIJ Int. 58 (2018) 921–928.
J. Lu, G. Cheng, J. Che, L. Wang, G. Xiong, Met. Mater. Int. 25 (2019) 473–486.
H. Sun, L. Li, J. Wang, X. Cheng, F. Zhou, Ironmak. Steelmak. 45 (2018) 708–713.
H. Sun, L. Li, D. Ye, X. Wu. Metall. Mater. Trans. B 49 (2018) 1909–1918.
J.I. Takamura, S. Mizoguchi, in: Y. Yagi (Ed.), IISC. The Sixth International Iron and Steel Congress, Iron and Steel Institute of Japan, Nagoya, Japan, 1990, pp. 591–597.
J. Lu, G. Cheng, L. Chen, G. Xiong, L. Wang, ISIJ Int. 58 (2018) 1307–1315.
F. Li, H. Li, D. Huang, S. Zheng, J. You, Met. Mater. Int. 24 (2018) 1394–1402.
Acknowledgements
The authors are grateful to the financial support provided by the National Natural Science Foundation of China (Grant Nos. 51874034 and 51674024).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lu, Jl., Cheng, Gg., Wu, M. et al. Detection and analysis of magnetic particle testing defects on heavy truck crankshaft manufactured by microalloyed medium-carbon forging steel. J. Iron Steel Res. Int. 27, 608–616 (2020). https://doi.org/10.1007/s42243-019-00334-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s42243-019-00334-7