Abstract
The internal flow field of an axial-flow pump under low flow rate conditions is extremely turbulent. The unstable flow region is formed due to the tip leakage and the rotating stall, and is distinguished by a saddle patterned zone in its flow-head curve that demonstrates restrictions in its workable flow range. It is therefore important to understand and improve the operational characteristics of an axial-flow pump under low flow rate conditions. In this study, experiments are performed for the performances of an axial-flow pump at the flow rate in a range between 0.8Qd and 1.2Qd, with the internal flow field measured by the particle image velocimetry (PIV), and with the pump performances and the internal flow field simulated by the Ansys CFX. The simulation results agree well with the experimental results. From the predicted heads at the flow rate in the range between 0.1Qd and 0.7Qd by the numerical simulation, the complete flow-head curves are obtained. The streamlines and the velocity contours in the region in front of the impeller leading edge under different flow conditions are analyzed. By adopting the double-inlet structures, the flow-head characteristics are studied by varying the values of δ and σ respectively, where δ denotes the gap between the inner cylinder end and the impeller leading edge, and σ denotes the gap between the inner cylinder and the outer cylinder. The findings indicate that with the double-inlet design, the velocity distribution can be effectively improved in the region in front of the impeller leading edge, as well as the head performance under the low flow rate conditions, and the positive slope value of the head curve is reduced in the unstable flow range. The optimal δ and σ values are determined.
Similar content being viewed by others
References
Shi W. D., Li T. T., Zhang D. et al. Numerical simulation of tip clearance leakage vortex flow characteristic in axial-flow pump [J]. IOP Conference Series Earth and Environmental Science, 2012, 15(7): 072023.
Pei J., Meng F., Li Y. et al. Fluid-structure coupling analysis of deformation and stress in impeller of an axial-flow pump with two-way passage [J]. Advances in Mechanical Engineering, 2016, 8(4): 1–11.
Benra F. K., Dohmen H. J., Schmidt M. Flow phenomena in a highly-loaded single-stage axial-flow pump-comparison of experimental and numerical results [C]. Proceedings of the 5th Joint ASME/JSME fluids Engineering Division Summer Conference, Houston, TX, USA, 2007.
Schrapp H., Stark U., Goltz, I. et al. Structure of the rotor tip flow in a highly-loaded single-stage axial-flow pump approaching stall: part I- Breakdown of the tip-clearance vortex [C]. Proceedings of the ASME Heat Transfer/Fluids Engineering Summer Conference, Charlotte, NC, USA, 2004.
Goltz I., Kosyna G., Wulff D. et al. Structure of the rotor tip flow in a highly-loaded single-stage axial-flow pump approaching stall: part II-stall inception-understanding the mechanism and overcoming its negative impacts [C]. Proceedings of the ASME Heat Transfer/Fluids Engineering Summer Conference, Charlotte, NC, USA, 2004.
Shi W., Zhang H., Chen B. et al. Numerical simulation of internal flow field in axial-flow pump with different blade tip clearance sizes [J]. Journal of Drainage and Irrigation Machinery Engineering, 2010, 28(5): 374–377(in Chinese).
Wu S. Q., Shi W. D., Zhang D. et al. Influence of blade tip rounding on tip leakage vortex cavitation of axial flow pump [J]. IOP Conference Series: Materials Science and Engineering, 2013, 52(6): 062011.
Zhang D., Shi L., Shi W. et al. Numerical analysis of unsteady tip leakage vortex cavitation cloud and unstable suction-side-perpendicular cavitation vortices in an axial-flow pump [J]. International Journal of Multiphase Flow, 2015, 77: 244–259.
Zhang D., Shi W., van Esch B. P. M. (Bart) et al. Numerical and experimental investigation of tip leakage vortex trajectory and dynamics in an axial-flow pump [J]. Computers and Fluids, 2015, 112: 61–71.
Zhang D. S., Shi W. D., Chen B. et al. Unsteady flow analysis and experimental investigation of axial-flow pump [J]. Journal of Hydrodynamics, 2010, 22(1): 35–43.
Zhang D., Shi W., Pan D. et al. Numerical and experimental investigation of tip leakage vortex cavitation patterns and mechanisms in an axial flow pump [J]. Journal of Fluids Engineering, 2015, 137(12): 121103.
Han C. Z., Xu S., Cheng H. Y. et al. LES method of the tip clearance vortex cavitation in a propelling pump with special emphasis on the cavitation-vortex interaction [J]. Journal of Hydrodynamics, 2020, 32(6): 1212–1216.
Kosyna G., Goltz I., Stark U. Flow structure of an axial-flow pump from stable operation to deep stall [C]. Proceedings of the ASME 2005 Fluids Engineering Division Summer Meeting, FEDSM2005, Houston, TX, USA, 2005, 1389–1396.
Goltz I., Kosyna G., Stark U. et al. Stall inception phenomena in a single-stage axial-flow pump [J]. Proceedings of the Institution of Mechanical Engineers Part A: Journal of Power and Energy, 2003, 217(4): 471–479.
Goltz I., Kosyna G., Wulff D. et al. Part load operating performance and stall inception of a single-stage axial-flow pump [C]. Proceedings of the 10thInternational Symposium on Transport Phenomena and Dynamics of Rotating machinery, Honolulu, Hawaii, USA, 2004.
Goltz I., Kosyna G., Wulff D. et al. Performance instability of an axial-flow pump: Origin and prevention [C]. Proceedings of the International Pumps User Forum, Karlsruhe, Germany, 2004.
Kurokawa J. J-groove technique for suppressing various anomalous flow phenomena in turbomachines [J]. International Journal of Fluid Machinery and Systems, 2011, 4(1): 1–13.
Pérez Flores P., Kosyna G., Wulff D. Suppression of performance curve instability of an axial-flow pump by using a double-inlet-nozzle [J]. International Journal of Rotating Machinery, 2008, ID 536850.
Li X., Chen H., Chen B. et al. Investigation of flow pattern and hydraulic performance of a centrifugal pump impeller through the PIV method [J]. Renewable Energy, 2020, 162: 561–574.
Zhang H., W Shi W., Chen B. et al. Experimental study of flow field in interference area between impeller and guide vane of axial flow pump [J]. Journal of Hydrodynamics, 2014, 26(6): 894–901.
Zhang H., Shi W., Chen B. et al. PIV measurement and numerical calculation for impeller inlet flow field in axial flow pump [J]. Journal of Drainage and Irrinage machinery Engineering, 2016, 32(6): 461–465(in Chinese).
Zhou L., Shi W., Lu W. et al. Numerical investigations and performance experiments of a deep-well centrifugal pump with different diffusers [J]. Journal of Fluids Engineering, 2012, 134(7): 071102.
Acknowledgments
This work was supported by the Fundamental Research Fund for Central Universities (Grant No. JZ2015HGBZ0129), the Open End Fund of Jiangsu University (Grant No. NRCP201603).
Author information
Authors and Affiliations
Corresponding author
Additional information
Biography: Yong-sheng Zhou (1972-), Male, Ph. D. Candidate
Rights and permissions
About this article
Cite this article
Zhou, Ys., Zhang, H. & Chen, B. Influence of double-inlet design on the flow-head characteristics of axial-flow pump. J Hydrodyn 33, 763–772 (2021). https://doi.org/10.1007/s42241-021-0069-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s42241-021-0069-x