Parameter Study and Improvement of Gearbox Whine Noise in Electric Vehicle

Abstract

Gearbox whine noise can seriously reduce the interior sound quality in an electric passenger car. In this work, a six-degree-of-freedom (6-DOF) dynamic model of a helical gear system was constructed and the mechanism for generation of whine noise was analyzed. The root cause of the problem was found through noise, vibration and harshness (NVH) testing of the gearbox and the vehicle. A rigid-elastic coupling dynamics model of the reducer assembly was then developed. The accuracy of the model was then validated via modal testing. The structure-borne noise of the reducer under full acceleration conditions was predicted using the acoustic structure coupling model and the rigid-elastic coupling model of the reducer. Gear parameters including the pressure angle, the helix angle and the contact ratio were studied to determine their effects on the whine noise. Gear tooth microgeometry modification parameters were then optimized to reduce the transmission error of the first pair of meshing gears. Finally, the whine noise from the gearbox was eliminated.

This is a preview of subscription content, log in to check access.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

References

  1. 1.

    Yoo, J., Kang, K.T., Huh, J. W., et al.: The mechanism and solution of harmonic gear whine noise in automotive transmission system. In: ASME 2007 International Design Engineering Technical Conferences, pp. 9 (2007)

  2. 2.

    Perret-Liaudet, J., Carbonelli, A., Rigaud, E.: Modeling of gearbox whining noise. SAE Technical Paper. 2014-01-2090 (2014)

  3. 3.

    Meier, C., Lieske, D., Bikker, S.: NVH-development of electric powertrains—CAE-methods and NVH-criteria. SAE Technical Paper. 2014-01-2072 (2014)

  4. 4.

    Abe, T., Cheng, Y., Nowaczyk, K.: Practical methods for managing the gear whine phenomena. In: ASME 2007 International Design Engineering Technical Conferences, pp. 9 (2007)

  5. 5.

    Krishnaswami, R., Kaatz, S., Hildebrand, D.: Gear whine reduction for a new automatic transmission. SAE Technical Paper. 2001-01-1506, pp. 9 (2001)

  6. 6.

    Shin, W., Kanase, A., Hwang, S., et al.: 6 speed automatic transmission vibration magnitude prediction and whine noise improvement through transmission system modeling. SAE Technical paper. 2011-01-1553 (2011)

  7. 7.

    Fang, Y., Zhang, T.: Sound quality investigation and improvement of an electric powertrain for electric vehicles. IEEE Trans. Ind. Electron. 65(2), 58 (2018)

    Article  Google Scholar 

  8. 8.

    Tosun, M., Yıldız, M., Özkan, A.: Investigation and refinement of gearbox whine noise. Appl. Acoust. 130, 305–311 (2018)

    Article  Google Scholar 

  9. 9.

    Oh, S.: A study on modeling and optimization of tooth microgeometry for a helical gear pair. Int. J. Precis. Eng. Manuf. 14(3), 423–427 (2013)

    Article  Google Scholar 

  10. 10.

    Cai, Y.: Simulation on the rotational vibration of helical gears in consideration of the tooth separation phenomenon (A new stiffness function of helical involute tooth pair). J. Mech. Des. 117(9), 460–472 (1995)

    Article  Google Scholar 

  11. 11.

    Fietkau, P., Bertsche, B.: Influence of tribological and geometrical parameters on lubrication conditions and noise of gear transmissions. Mech. Mach. Theory 69, 303–320 (2013)

    Article  Google Scholar 

Download references

Acknowledgements

This work was supported by the State New Energy Vehicle Research Center and Beijing Electric Vehicle Co., Ltd.

Author information

Affiliations

Authors

Corresponding author

Correspondence to Shouyuan Zhang.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Zhang, S. Parameter Study and Improvement of Gearbox Whine Noise in Electric Vehicle. Automot. Innov. 1, 272–280 (2018). https://doi.org/10.1007/s42154-018-0029-5

Download citation

Keywords

  • Gearbox
  • Whine noise
  • Simulation
  • Electric vehicle