Abstract
In this paper, an attempt has been made for the use of waste fly ash cenosphere for tribological wear behaviour. LM6/cenosphere composites were fabricated by stir casting method. An experimental study has been conducted on pin-on-disc wear testing machine to determine the abrasive wear behaviour of cenosphere particulate-reinforced metal matrix composite. Studies were done by varying the load (5, 10, 15, and 20 N) on 5%, and 7.5, 10, and 12.5% weight percentages of reinforcement at a velocity of 1.0472 m/s. The results revealed that the wear resistance of the 10 wt% reinforced composites is superior to that of other reinforced and unreinforced composites. The worn surface morphology of the eroded surfaces wear was examined using scanning electron microscopy (SEM). The SEM analysis reveals the presence of both abrasive wear and delamination wear mechanism.
Similar content being viewed by others
References
Anshits NN, Vereshchagina TA, Bayukov OA, Salanov AN, Anshits AG (2005) The nature of nanoparticles of crystalline phases in cenospheres and morphology of their shells. Glass Phys Chem 31:306–315
Chauhan SR, Thakur S (2013) Effect of particle size, particle loading and sliding distance on the friction and wear properties of cenosphere particulate filled vinylester composites. Mater Des 51:398–408
Hutchings IM (1992) Tribology: friction and wear of engineering materials. Mater Des 13:187
Lee CS, Kim YH, Han KS, Lim T (1992) Wear behaviour of aluminium matrix composite materials. J Mater Sci 27:793–800
Mahendra KV, Radhakrishna K (2007) Fabrication of Al–4. 5% Cu alloy with fly ash metal matrix composites and its characterization. Mater Sci Pol 25:57–68
Mazahery A, Shabani MO, Rahimipour MR, Razavi M (2012) The numerical modeling of abrasion resistance in casting aluminum–silicon alloy matrix composites. J Compos Mater 46:2647–2658
Ramachandra M, Radhakrishna K (2007) Effect of reinforcement of flyash on sliding wear, slurry erosive wear and corrosive behavior of aluminium matrix composite. Wear 262:1450–1462
Rohatgi P (1991) Cast aluminum-matrix composites for automotive applications. JOM 43:10–15
Rohatgi PK (1994) Low-cost, fly-ash-containing aluminum-matrix composites. JOM 46:55–59
Rohatgi PK, Guo RQ (1997) Mechanism of abrasive wear of Al–Si hypoeutectic alloy containing 5 vol% fly ash. Tribol Lett 3:339–347
Rohatgi PK, Asthana R, Das S (1986) Solidification, structures, and properties of cast metal-ceramic particle composites. Int Met Rev 31:115–139
Rohatgi PK, Guo RQ, Huang P, Ray S (1997) Friction and abrasion resistance of cast aluminum alloy-fly ash composites. Metall Mater Trans A 28A:245–250
Shamsipour M, Pahlevani Z, Shabani MO, Mazahery A (2016) Optimization of the EMS process parameters in compocasting of high-wear-resistant Al-nano-TiC composites. Appl Phys A 122:1–14
Sharma SC (2000a) Effect of aging on oxidation behavior of aluminum-albite composites at high temperatures. J Mater Eng Perform 9:344–349
Sharma SC (2000b) Effect of albite particles on the coefficient of thermal expansion behavior of the Al6061 alloy composites. Metall Mater Trans A 31:773–780
Sharma SC, Girish BM, Kamath R, Satish BM (1999) Fractography, fluidity, and tensile properties of aluminum/hematite particulate composites. ASM-JMEPEG (J Mater Eng Perform) 8:309–314
Spurr RT (1979) Temperatures reached during sliding. Wear 55:289–293
Tofigh AA, Shabani MO (2013) Efficient optimum solution for high strength Al alloys matrix composites. Ceram Int 39:7483–7490
Vassilev SV, Menendez R, Diaz-Somoano M, Martinez-Tarazona MR (2004) Phase-mineral and chemical composition of coal fly ashes as a basis for their multicomponent utilization. 2. Characterization of ceramic cenosphere and salt concentrates. Fuel 83:585–603
Yu SR, Huang ZQ (2014) Dry sliding wear behavior of fly ash cenosphere/AZ91D Mg alloy composites. J Mater Eng Perform 23:3480–3488
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Bera, T., Acharya, S.K. Utilization of Fly Ash Cenosphere as Reinforcement for Abrasive Wear Behaviour of LM6 Al Alloy Metal Matrix Composites. Iran J Sci Technol Trans Mech Eng 43, 273–280 (2019). https://doi.org/10.1007/s40997-017-0132-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40997-017-0132-y