Skip to main content
SpringerLink
Log in

Numerical and Experimental Investigation of SS304L Cylindrical Shell with Cutout Under Uniaxial Cyclic Loading

  • Research Paper
  • Published:
Iranian Journal of Science and Technology, Transactions of Mechanical Engineering Aims and scope Submit manuscript

Abstract

This study examined the behavior of steel cylindrical shells under strain-controlled loading and axial cyclic loading. Experimental tests were carried out by an INSTRON 8802 servo-hydraulic. Under strain-controlled loading, the softening hysteresis curve is observed in shells. Because of buckling made in the compression area, the softening is intensified. Moreover, the effect of cutout on the behavior of hysteresis curves of steel cylindrical shells was also examined under this type of loading. The results show that cutout accelerates the softening behavior in steel cylindrical shells. Numerical analysis was performed by ABAQUS using hardening models. The accuracy of these models was compared with experimental results. Linear kinematic hardening model cannot simulate the softening behavior of the shell, but the model of nonlinear isotropic and kinematic hardening can simulate the softening behavior of the shell well. The residual plastic strain is obtained close to the experimental results with this model.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Fig. 27
Fig. 28

Similar content being viewed by others

References

  • ABAQUS (2009) Theory manual, v6.9.1, section 4.3.5: models for metals subjected to cyclic loading

  • ABAQUS (2009) Analysis user’s manual, v6.9.1, section 19.2.2, models for metals subjected to cyclic loading

  • ASTM (2005) ASTM A370-05. Standard test methods and definitions for mechanical testing of steel products, USA, pp 2–5

  • Avanzini A (2008) Mechanical characterization and finite element modeling of cyclic stress–strain behaviour of ultrahigh molecular weight polyethylene. Mater Des 29:330–343

    Article  Google Scholar 

  • Belattar A, Taleb L, Hauet A, Taheri S (2012) Dependence of the cyclic stress–strain curve on loading history and its interaction with fatigue of 304L stainless steel. Mater Sci Eng A 536:170–180

    Article  Google Scholar 

  • Chaboche JL, Lemaitre J (1990) Mechanics of solid materials. Cambridge University Press, Cambridge

    MATH  Google Scholar 

  • Chan CW, Man HC, Cheng FT (2013) Fatigue behavior of laser-welded NiTi wires in small-strain cyclic bending. Mater Sci Eng A 559:407–415

    Article  Google Scholar 

  • Chang KH, Pan WF (2009) Buckling life estimation of circular tubes under cyclic bending. Int J Solids Struct 46:254–270

    Article  Google Scholar 

  • Chang KH, Pan WF, Lee KL (2008) Mean moment effect of thin-walled tubes under cyclic bending. Struct Eng Mech 28:495–514

    Article  Google Scholar 

  • Chen G (2009) Ratcheting and fatigue properties of the high-nitrogen steel X13CrMnMoN18-14-3 under cyclic loading. Comput Mater Sci 46:572–578

    Article  Google Scholar 

  • Chena X (2005) Experimental study on ratcheting behavior of eutectic tin–lead solder under multi axial loading. Mater Sci Eng A 406:86–94

    Article  Google Scholar 

  • Chiou YC, Yip MC (2003) Effect of mean strain level on the cyclic stress–strain behavior of AISI 316 stainless steel. Mater Sci Eng A 354:270–278

    Article  Google Scholar 

  • Colin J, Fatemi A (2009) Variable amplitude cyclic deformation and fatigue behaviour of stainless steel 304L including step, periodic, and random loadings. Fatigue Fract Eng Mater Struct 33:205–220

    Article  Google Scholar 

  • Elchalakani M (2007) Plastic mechanism analyses of circular tubular members under cyclic loading. Thin Walled Struct 45:1044–1057

    Article  Google Scholar 

  • Elchalakani M, Zhao XL, Grzebieta R (2006) Variable amplitude cyclic pure bending tests to determine fully ductile section slenderness limits for cold-formed CHS. Eng Struct 28:1223–1235

    Article  Google Scholar 

  • Gao H, Chen X (2009) Effect of axial ratcheting deformation on torsional low cycle fatigue life of lead-free solder Sn–3.5Ag. Int J Fatigue 31:276–283

    Article  Google Scholar 

  • Gao Q, Kang GZ, Yang XJ (2003) Uniaxial ratcheting of SS304 stainless steel at high temperatures: visco-plastic constitutive model. J Theor Appl Fract Mech 40:105–111

    Article  Google Scholar 

  • Goggins JM, Broderick BM, Elghazouli AY, Lucas AS (2005) Experimental cyclic response of cold-formed hollow steel bracing members. Eng Struct 27:977–989

    Article  Google Scholar 

  • Han H, Cheng J, Taheri F, Pegg N (2006) Numerical and experimental investigations of the response of aluminum cylinders with a cutout subject to axial compression. Thin Walled Struct 44:254–270

    Article  Google Scholar 

  • Hanus E, Ericsson T (1995) Influence of four-point bending fatigue on the residual stress state of a pressure-rolled, particulate-reinforced metal matrix composite. Mater Sci Eng A 194:147–156

    Article  Google Scholar 

  • Hatami H, Nouri MD (2015) Experimental and numerical investigation of lattice-walled cylindrical shell under low axial impact velocities. Latin American J Solids Struct 12(10):1950–1971

  • Hatami H, Rad MS, Jahromi AG (2017) A theoretical analysis of the energy absorption response of expanded metal tubes under impact loads. International J Impact Eng 109:224–239

    Article  Google Scholar 

  • Jahromi GA, Hatami H (2017) Energy absorption performance on multilayer expanded metal tubes under axial impact. Thin-Walled Struct 116:1–11

  • Jiao R, Kyriakides S (2009) Ratcheting, wrinkling and collapse of tubes under axial cycling. Int J Solids Struct 46:2856–2870

    Article  Google Scholar 

  • Kang G, Liu Y (2008) Uniaxial ratcheting and low-cyclic fatigue failure of the steel with cyclic stabilizing or softening feature. Mater Sci Eng A 472:258–268

    Article  Google Scholar 

  • Kang GZ, Li YG, Zhang J, Sun YF, Gao Q (2005a) Uniaxial ratcheting and failure behaviors of two steels. J Theor Appl Fract Mech 43:199–209

    Article  Google Scholar 

  • Kang GZ, Li Y, Gao Q, Kan QH, Zhang J (2005b) Uniaxial ratchetting in steels with different cyclic softening/hardening behaviours. Fatigue Fract Eng Mater Struct 29:93–103

    Article  Google Scholar 

  • Kang G, Liu Y, Li Z (2006) Experimental study on ratchetting-fatigue interaction of SS304 stainless steel in uniaxial cyclic stressing. Mater Sci Eng A 435:396–404

    Article  Google Scholar 

  • Kulkarni SC, Desai YM, Kant T, Reddy GR, Prasad P, Vaze KK, Gupta C (2004) Uniaxial and biaxial ratchetting in piping materials—experiments and analysis. Int J Press Vessels Pip 81:609–617

    Article  Google Scholar 

  • Lim CB, Kim KS, Seong JB (2009) Ratcheting and fatigue behavior of a copper alloy under uniaxial cyclic loading with mean stress. Int J Fatigue 31:501–507

    Article  Google Scholar 

  • Nip KH, Gardner L, Davies CM, Elghazouli AY (2010a) Extremely low cycle fatigue tests on structural carbon steel and stainless steel. J Constr Steel Res 66:96–110

    Article  Google Scholar 

  • Nip KH, Gardner L, Elghazouli AY (2010b) Cyclic testing and numerical modelling of carbon steel and stainless steel tubular bracing members. Eng Struct 32:424–441

    Article  Google Scholar 

  • Nouri MD, Hatami H (2014) Experimental and numerical study of the effect of longitudinal reinforcements on cylindrical and conical absorbers under impact loading. Indian J Sci Technol 7(2):199–210

  • Nouri MD, Hatami H, Jahromi AG (2015) Experimental and numerical investigation of expanded metal tube absorber under axial impact loading. Struct Eng Mech 54(6):1245–1266

  • Owen DRJ, Hinton F (1980) Finite elements in plasticity—theory and practice. Pineridge Press Ltd, Swansea

    MATH  Google Scholar 

  • Paula SK, Sivaprasada S, Dharb S, Tarafdera S (2010) Cyclic plastic deformation and cyclic hardening/softening behavior in 304LN stainless steel. J Theor Appl Fract Mech 54:63–70

    Article  Google Scholar 

  • Pham MS, Solenthaler C, Janssens KGF, Holdsworth SR (2011) Dislocation structure evolution and its effects on cyclic deformation response of AISI 316L stainless steel. Mater Sci Eng A 528:3261–3269

    Article  Google Scholar 

  • Rahman SM, Hassan T, Corona E (2008) Evaluation of cyclic plasticity models in ratcheting simulation of straight pipes under cyclic bending and steady internal pressure. Int J Plast 24:1756–1791

    Article  MATH  Google Scholar 

  • Shariati M, Rokhi MM (2008) Numerical and experimental investigations on buckling of steel cylindrical shells with elliptical cutout subject to axial compression. Thin Walled Struct 46:1251–1261

    Article  Google Scholar 

  • Shariati M, Hatami H, Yarahmadi H, Eipakchi HR (2011a) An experimental study on the ratcheting and fatigue behavior of polyacetal under uniaxial cyclic loading. Mater Des 34:302–312

    Article  Google Scholar 

  • Shariati M, Hatami H, Eipakchi HR, Yarahmadi H, Torabi H (2011b) Experimental and numerical investigations on softening behavior of POM under cyclic strain-controlled loading. Polym Plast Technol Eng 50:1576–1582

    Article  Google Scholar 

  • Shariati M, Hatami H (2012) Experimental study of SS304L cylindrical shell with/without cutout under cyclic axial loading. Theoretical Appl Fracture Mechanics 58(1);35–43

    Article  Google Scholar 

  • Shariati M, Hatami H, Torabi H, Epakchi HR (2012) Experimental and numerical investigations on the ratcheting characteristics of cylindrical shell under cyclic axial loading. Struct Eng Mech 44(6):753–762

    Article  Google Scholar 

  • Sih GC (1991) Mechanics of fracture initiation and propagation. Kluwer Academic Publisher, Boston

    Book  Google Scholar 

  • Sun GQ, Shang DG (2010) Prediction of fatigue lifetime under multi axial cyclic loading using finite element analysis. Mater Des 31:126–133

    Article  Google Scholar 

  • Tafreshi A (2002) Buckling and post-buckling analysis of composite cylindrical shells with cutouts subjected to internal pressure and axial compression loads. Int J Press Vessels Pip 79:351–359

    Article  Google Scholar 

  • Yang X (2005) Low cycle fatigue and cyclic stress ratcheting failure behavior of carbon steel 45 under uniaxial cyclic loading. Int J Fatigue 27:1124–1132

    Article  Google Scholar 

  • Yoon S, Hong SG, Lee SB, Kim BS (2003) Low cyclic fatigue testing of 429EM stainless steel pipe. Int J Fatigue 8:1301–1307

    Article  Google Scholar 

  • Zakavi SJ, Zehsaz M, Eslami MR (2010) The ratchetting behavior of pressurized plain pipework subjected to cyclic bending moment with the combined hardening model. Nucl Eng Des 240:726–737

    Article  Google Scholar 

  • Zhang C, Liu Y, Goto Y (2008) Plastic buckling of cylindrical shells under transverse loading. Tsinghua Sci Technol 13:202–210

    Article  Google Scholar 

  • Zhang J, Yu Q, Jiang Y, Li Q (2011) An experimental study of cyclic deformation of extruded AZ61A magnesium alloy. Int J Plast 27:768–787

    Article  MATH  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Lorestan University, Khorramabad, Lorestan, Iran

    Hossein Hatami

  2. Department of Mechanical Engineering, Ferdowsi University, Mashhad, Iran

    Mahmoud Shariati

Authors
  1. Hossein Hatami
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Mahmoud Shariati
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Hossein Hatami.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Hatami, H., Shariati, M. Numerical and Experimental Investigation of SS304L Cylindrical Shell with Cutout Under Uniaxial Cyclic Loading. Iran J Sci Technol Trans Mech Eng 43, 139–153 (2019). https://doi.org/10.1007/s40997-017-0120-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40997-017-0120-2

Keywords

Search

Navigation