Abstract
This paper investigates the effect of low concentrations of sodium hydroxide (NaOH) and alkaline ratio (wt. of alkali silicate/alkali hydroxide) on the physical and mechanical properties of alkali-activated GGBFS. Parameters considered are activator concentration (1, 2, 3, 4, 5, 6, 7, 8, 9M) and alkaline ratio (1, 1.5, 2, 2.5, 3). Normal consistency, initial setting time and compressive strength tests were performed considering GGBFS as binder and alkaline solution as fluid medium with varying NaOH concentration and alkaline ratio. The obtained results indicated that change in NaOH concentration has significant effect on consistency, initial setting time and compressive strength of alkali-activated GGBFS. Change in alkaline ratio showed a significant effect in initial setting time and compressive strength of alkali-activated GGBFS. Compressive strength of mortar cubes cast with 4M NaOH with an alkaline ratio of 1.5 cured at room temperature produced a strength of 41 MPa at 28 days. XRD analysis indicated that increase in NaOH concentration resulted in increase in the intensity of albite peaks. SEM analysis indicated a complete dissolution of slag grains, and the gel was observed to be homogenous on slag particles at higher activator concentration.
Similar content being viewed by others
References
Allahverdi A, Shaverdi B, Kani EN (2010) Influence of Sodium Oxide on Properties of Fresh and Hardened Paste of Alkali-Activated Blast-Furnace Slag. Int J Civ Eng 8:304–314
Bakharev T (2000) Alkali activated slag concrete: Chemistry, microstructure and durability. Dissertation, Monash University, Melbourne
Bhowmick A, Ghosh S (2012) Effect of synthesizing parameters on workability and compressive strength of fly ash based geopolymer mortar. Int J Civil Struct Engg 3(1):168–177
Chang JJ (2003) A study on the setting characteristics of sodium silicate-activated slag pastes. Cem Concr Res 33:1005–1011
Chindaprasirt P, De Silva P, Sagoe-Crentsil K, Hanjitsuwan S (2012) Effect of SiO2 and Al2O3 on the setting and hardening of high calcium fly ash-based geopolymer systems. J Mater Sci 47:4876–4883
Davidovits J (1994) Properties of geopolymer cements. Alkaline Cem Concr, Kiev, Ukraine, pp 131–149
Davidovits J, Comrie DC, Paterson JH, Ritcey DJ (1990) Geopolymeric concretes for environmental protection. ACI Concr Int 12(7):30–40
De Silva P, Sagoe-Crenstil K (2008) The Effect of Al2O3 and SiO2 On Setting and Hardening of Na2O-Al2O3-SiO2-H2O Geopolymer Systems. J Aust Ceram Soc 44:39–46
Djobo JN, Tchakouté HK, Ranjbar N, Elimbi A, Tchadjié LN, Njopwouo D (2016) Gel composition and strength properties of alkali-activated oyster shell-volcanic ash: effect of synthesis conditions. J Am Ceram Soc 99(9):3159–3166
Ganapati Naidu P, Prasad ASSN, Adiseshu S, Satayanarayana PVV (2012) A study on strength properties of geopolymer concrete with addition of G.G.B.S. Int J Eng Res Develop 2:19–28
Garcia-Lodeiro I, Palomo A, Fernandez-Jimenez A, Macphee DE (2011) Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram Na2O–CaO–Al2O3–SiO2–H2O. Cem Concr Res 41:923–931
Garcia-Lodeiro I, Fernandez-Jimenez A, Palomo A (2013) Hydration kinetics in hybrid binders: early reaction stages. Cement Concr Compos 39:82–92
Hardjito D, Cheak CC, Ing CHL (2008) Strength and setting times of low calcium fly ash based geopolymer mortar. Mod Appl Sci 2(4):3–11
Heah CY, Kamarudin H, Mustafa Al Bakri AM, Bnhussain M, Luqman M, Khairul Nizar I, Ruzaidi CM, Liew YM (2013) Kaolin-based geopolymers with various NaOH concentrations. Int J Miner Metall Mater 20:313–322
Hu S, Wang H, Zhang G, Ding Q (2008) Bonding and abrasion resistance of geopolymeric repair material made with steel slag. Cement Concr Compos 30(3):239–244
IS 383 (1970) Specification for coarse and fine aggregates from natural sources for concrete. Bureau of Indian Standards, New Delhi
IS 4031(Part 4) (1988) Method of physical tests for hydraulic cement - Determination of consistency of standard cement paste. Bureau of Indian Standards, New Delhi
IS 4031(Part 5) (1988) Method of physical tests for hydraulic cement - Determination of initial and final setting times. Bureau of Indian Standards, New Delhi
IS 4031(Part 6) (1988) Method of physical tests for hydraulic cement - Determination of compressive strength of hydraulic cement other than masonry cement. Bureau of Indian Standards, New Delhi
Ismail I, Bernal SA, Provis JL, San Nicolas R, Hamdan S, van Deventer JSJ (2014) Modification of phase evolution in alkali-activated blast furnace slag by the incorporation of fly ash. Cem Concr Compos 45:125–135
Kim HS, Park JW, An YJ, Bae JS, Han C (2011) Activation of ground granulated blast furnace slag cement by calcined alunite. Mater Transact 52:210–218
Kroehong W, Sinsiri T, Jaturapitakkul C, Chindaprasirt P (2011) Effect of palm oil fuel ash fineness on the microstructure of blended cement paste. Constr Build Mater 25(11):4095–4104
Kumar S, Kumar R, Mehrotra SP (2010) Influence of granulated blast furnace slag on the reaction, structure and properties of fly ash based geopolymer. J Mater Sci 45(3):607–615
Li C, Sun H, Li L (2010) A review: the comparison between alkali-activated slag (Si + Ca) and metakaolin (Si + Al) cements. Cem Concr Res 40(9):1341–1349
Mallikarjuna Rao G, Gunneswara Rao TD (2015) Final setting time and compressive strength of fly ash and ggbs-based geopolymer paste and mortar. Arab J Sci Eng 40(11):3067–3074
Phoo-ngernkham T, Chindaprasirt P, Sata V, Pangdaeng S, Sinsiri T (2013) Properties of high calcium fly ash geopolymer pastes containing Portland cement as additive. Int J Miner Metall Mater 20(2):214–220
Phoo-ngernkham T, Maegawa A, Mishima N, Hatanaka S, Chindaprasirt P (2015) Effects of sodium hydroxide and sodium silicate solutions on compressive and shear bond strengths of FA–GBFS geopolymer. Constr Build Mater 91:1–8
Puertas F, Martınez-Ramırez S, Alonso S, Vazquez T (2000) Alkali-activated fly ash/slag cements: strength behaviour and hydration products. Cem Concr Res 30(10):1625–1632
Qureshi MN, Ghosh S (2014) Effect of silicate content on the properties of alkali-activated blast furnace slag paste. Arab J Sci Eng 39:5905–5916
Ranjbar N, Mehrali M, Behnia A, Alengaram UJ, Jumaat MZ (2014) Compressive strength and microstructural analysis of fly ash/palm oil fuel ash based geopolymer mortar. Mater Des 59:532–539
Rattanasak U, Pankhet K, Chindaprasirt P (2011) Effect of chemical admixtures on properties of high-calcium fly ash geopolymer. Int J Miner Metall Mater 18:364–369
Ravikumar D, Peethamparan S, Neithalath N (2010) Structure and strength of NaOH activated concretes containing fly ash or GGBFS as the sole binder. Cement Concr Compos 32(6):399–410
Ridtirud C, Chindaprasirt P, Pimraksa K (2011) Factors affecting the shrinkage of fly ash geopolymers. Int J Miner Metall Mater 18:100–104
Suksiripattanapong C, Horpibulsuk S, Chanprasert P, Sukmak P, Arulrajah A (2015) Compressive strength development in geopolymer masonry units manufactured from water treatment sludge. Constr Build Mater 82:20–30
Swaddle TW (2001) Silicate complexes of aluminium (III) in aqueous systems. Coord Chem Rev 219:665–686
Tchadjié LN, Djobo JNY, Ranjbar N, Tchakouté HK, Kenne BBD, Elimbi A, Njopwouo D (2016) Potential of using granite waste as raw material for geopolymer synthesis. Ceram Int 42(2):3046–3055
Wallah SE, Rangan BV (2006) Low-calcium fly ash-based geopolymer concrete: long-term properties, Dissertation, Curtin University, Australia pp.76-80
Xu H, Van Deventer JSJ (2000) The geopolymerisation of alumino-silicate minerals. Int J Miner Process 59:247–266
Acknowledgements
The authors are thankful for the support from all the faculty members of Civil Engineering Department, National Institute of Technology, Warangal, India.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Thunuguntla, C., Gunneswara Rao, T. Appraisal on Strength Characteristics of Alkali-Activated GGBFS with Low Concentrations of Sodium Hydroxide. Iran J Sci Technol Trans Civ Eng 42, 231–243 (2018). https://doi.org/10.1007/s40996-018-0113-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40996-018-0113-4