Abstract
The main objective of ISO/TC 261 is to standardise the processes of Additive Manufacturing, the process chains (Data, Materials, Processes, Hard- and Software, Applications), test procedures, quality parameters, supply agreements, environment, health and safety, fundamentals and vocabularies. This section provides readers with news regarding standardisation efforts of ISO/TC 261. Further up-to-date information regarding recently published documents, such as new standards, revised standards, the status of standards can be found in the ISO/TC261 webpages: https://www.iso.org/committee/629086.html and the committee webpages: https://committee.iso.org/sites/tc261/home/news.html.
Avoid common mistakes on your manuscript.
International organisation for standardisation (2023) 21st plenary meeting of ISO/TC 261 “additive manufacturing” held on 31 march 2023 at penn state university, USA
-
1.
New projects
-
1.1
ISO/ASTM PWI 52,961 “Additive manufacturing of polymers–Environment, health and safety–General principles for use of polymers” registered as a preliminary work item and assigned to ISO/TC 261/JG 69 with a mature document for ISO/NP-ballot and ASTM F42.06 Sub-Committee Ballot due end of Q4/2024.
-
2.
Project updates
-
2.2
ISO/ASTM PWI 52,954 will be split into two parts: ISO/ASTM PWI 52,954–1 “Additive Manufacturing—Qualification principles—Common failure modes used for risk mapping”, and ISO/ASTM PWI 52,954–2 “Additive Manufacturing—Qualification principles—Specific PBF-LB/M failure modes used for risk mapping”.
-
3.
Project stage updates
-
3.1
ISO/ASTM AWI 52,957 “Additive Manufacturing—Design—Parts using ceramic materials”, will skip the CD-stage and to be registered as stage code 30.99 “CD approved for registration as DIS”.
-
3.2
ISO/ASTM AWI 52,919 “Additive manufacturing—Qualification principles—Test method of sand moulds for metal casting” will skip the CD-stage and to be registered as stage code 30.99 “CD approved for registration as DIS”.
-
3.3
SO/ASTM AWI 52,958 “Additive Manufacturing of Metals—Powder Bed Fusion—Practice for In-Situ Flaw Detection and Analysis for Laser-based PBF” will skip the CD-stage and to be registered as stage code 30.99 “CD approved for registration as DIS”.
-
3.4
3.4 ISO/ASTM AWI 52,959 “Additive Manufacturing—Test Artifacts —Compression Validation Coupons for Lattice Designs” will skip the CD-stage and to be registered as stage code 30.99 “CD approved for registration as DIS”.
-
4.
Project extensions
-
4.1
ISO/ASTM 52,933 “Additive manufacturing—Environment, health and safety—Test method for the hazardous substances emitted from material extrusion type 3D printers in the non-industrial places” will have a project extension for 9 months, updating the next target dates to 2024–06-05 for Stage 50.00 “Final text received or FDIS registered for formal approval”; and 2024–09-05 for stage 60.60 “International Standard published”.
-
5.
Revisions
-
5.1
ISO/ASTM 52,901:2017 “Additive manufacturing—General principles—Requirements for purchased AM parts” due for revision with regards to normative references and terminology.
-
6.
Change of name and scope
-
6.1
ISO/TC 261/JG 69 “Joint ISO/TC 261-ASTM F 42 Group: EH&S for use of metallic materials” to have a change of title and scope to “Joint ISO/TC 261-ASTM F 42 Group: EH&S for use of metallic and polymer materials”, with the scope changed to “ISO/TC 261/JG69 is a Joint Group developing documents related to Environment, Health and Safety (EHS) aspects in all Additive Manufacturing processes that use metallic and polymer materials for industrial use, consisting from the supply of feedstock to the delivery of parts. The documents include, but are not limited to the identification of hazards, risk assessment, recommendations for protective and preventive measures, verification protocols, and waste disposal management.”
Data availability
No datasets are available.
Reference
International Organisation for Standardisation (2023) 21st Plenary Meeting of ISO/TC 261 “Additive Manufacturing” held on 31 March 2023. ISO/TC 261 N 1361.
Funding
Not applicable.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
Not applicable.
Ethics approval
Not applicable.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Pei, E., Seidel, C. Standardisation efforts of ISO/TC 261 “additive manufacturing” 21st plenary meeting of ISO/TC 261 “additive manufacturing”. Prog Addit Manuf 8, 1143–1144 (2023). https://doi.org/10.1007/s40964-023-00448-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40964-023-00448-1