Abstract
Fatigue tests under high static pre-stress loads can provide meaningful results to better understand the time-dependent failure characteristics of rock and rock-like materials. However, fatigue tests under high static pre-stress loads are rarely reported in previous literature. In this study, the rock specimens were loaded with a high static pre-stress representing 70% and 80% of the uniaxial compressive strength (UCS), and cyclic fatigue loads with a low amplitude (i.e., 5%, 7.5% and 10% of the UCS) were applied. The results demonstrate that the fatigue life decreased as the static pre-stress level or amplitude of fatigue loads increased for different rock types. The high static pre-stress affected the fatigue life greatly when the static pre-stress was larger than the damage stress of rocks in uniaxial compression tests. The accumulative fatigue damage exhibited three stages during the fatigue failure process, i.e., crack initiation, uniform velocity, and acceleration, and the fatigue modulus showed an “S-type” change trend. The lateral and volumetric strains had a much higher sensitivity to the cyclic loading and could be used to predict fatigue failure characteristics. It was observed that volumetric strain \(\varepsilon _{{\text{v}}}\) = 0 is a threshold for microcracks coalescence and is an important value for estimating the fatigue life.
Article highlights
-
Fatigue mechanical performance of high static pre-stressed rocks were evaluated.
-
The results demonstrate that the fatigue life decreased as the static pre-stress level increased and the static pre-stress affected the fatigue life more than the amplitude of fatigue loads.
-
The volumetric strain of zero before fatigue loading is a threshold for fatigue failure of rocks under high static stress.
Similar content being viewed by others
Abbreviations
- σ s :
-
Static stress
- σ :
-
Stress
- UCT:
-
Uniaxial compression test
- UFT:
-
Uniaxial fatigue test
- σ 1 :
-
The major principal stress
- σ 2 :
-
The intermediate principal stress
- σ ucs :
-
Uniaxial compressive strength (UCS)
- σ max :
-
Peak value of fatigue cyclic loads
- σ min :
-
Valley value of fatigue cyclic loads
- σ mea :
-
Average value of fatigue cyclic loads
- µ :
-
Poisson’s ratio of elastic stage in UCT
- σ fs :
-
Fatigue strength
- n :
-
Number of fatigue loads
- εl :
-
Lateral strain
- E y :
-
Young’s modulus in UCT
- σ x :
-
Initial stress point of elastic stage in UCT
- σ y :
-
End stress point of elastic stage in UCT
- σ 50 :
-
Stress level with value equals to half of σucs in UCT
- E dtm :
-
Dynamic tangent modulus
- σ d :
-
Dynamic stress
- ε:
-
Strain
- t :
-
Loading time
- VL :
-
Wave velocity of rock specimen before testing
- σ 3 :
-
The minor principal stress
- W f :
-
Wave form
- T fl :
-
Fatigue life
- ε max :
-
Axial strain on peak value of fatigue cyclic loads
- ε min :
-
Axial strain on valley value of fatigue cyclic loads
- ε mea :
-
Axial strain on average value of fatigue cyclic loads
- µ c :
-
Poisson’s ratio during the whole testing process
- f :
-
Frequency of fatigue loads
- ε a :
-
Axial strain
- ε v :
-
Volumetric strain
- E s :
-
Secant modulus in UCS test
- ε x :
-
Initial strain point of elastic stage in UCT
- ε y :
-
End strain point of elastic stage in UCT
- ε 50 :
-
Strain point at the σ50 in UCT
- E dsm :
-
Dynamic secant modulus
References
Attewell PB, Farmer IW (1973) Fatigue behavior of rock. Int J Rock Mech Min Sci 10(1):1–9. https://doi.org/10.1016/0148-9062(73)90055-7
Bagde MN, Petros V (2005a) Fatigue properties of intact sandstone samples subjected to dynamic uniaxial cyclical loading. Int J Rock Mech Min Sci 42(2):237–250. https://doi.org/10.1016/j.ijrmms.2004.08.008
Bagde MN, Petros V (2005b) Waveform effect on fatigue properties of intact sandstone in uniaxial cyclical loading. Rock Mech Rock Eng 38(3):169–196. https://doi.org/10.1007/s00603-005-0045-8
Bagde MN, Petros V (2009) Fatigue and dynamic energy behavior of rock subjected to cyclical loading. Int J Rock Mech Min Sci 46(1):200–209. https://doi.org/10.1016/j.ijrmms.2008.05.002
Brown ET, Brady BHG (1978) Trends in relationships between measured rock in situ stress and depth. Int J Rock Mech Min Sci Geomech Abstr 15(4):211–215. https://doi.org/10.1016/0148-9062(78)91227-5
Cerfontaine B, Collin F (2018) Cyclic and fatigue behaviour of rock materials: review, interpretation and research perspectives. Rock Mech Rock Eng 51:391–414. https://doi.org/10.1007/s00603-017-1337-5
Chen Y, Watanabe K, Kusuda H, Kusaka E, Mabuchi M (2011) Crack growth in westerly granite during a cyclic loading test. Eng Geol 117(3–4):189–197. https://doi.org/10.1016/j.enggeo.2010.10.017
Du K, Tao M, Li XB, Zhou J (2016) Experimental study of slabbing and rockburst induced by true-triaxial unloading and local dynamic disturbance. Rock Mech Rock Eng 49(9):1–17. https://doi.org/10.1007/s00603-016-0990-4
Du K, Su R, Tao M, Yang CZ, Momeni A, Wang SF (2019) Specimen shape and cross-section effects on the mechanical properties of rocks under uniaxial compressive stress. Bull Eng Geol Environ 78:6061–6074. https://doi.org/10.1007/s10064-019-01518-x
Du K, Li XF, Yang CZ, Zhou J, Chen SJ, Khandelwal M (2020) Experimental investigations on mechanical performance of rocks under fatigue loads and biaxial confinements. J Cent South Univ 27:2985–2998. https://doi.org/10.1007/s11771-020-4523-7
Du K, Li XF, Tao M, Wang SF (2020b) Experimental study on acoustic emission (AE) characteristics and crack classification during rock fracture in several basic lab tests. Int J Rock Mech Min Sci 133:104411. https://doi.org/10.1016/j.ijrmms.2020.104411
Du K, Liu MH, Yang CZ, Tao M, Feng FK, Wang SF (2021) Mechanical and acoustic emission (AE) characteristics of rocks under biaxial confinements. Appl Sci 11(769):769. https://doi.org/10.3390/app11020769
Feng CL, Wu XQ, Ding DX, Wu YF (2009) Investigation on fatigue characteristics of white sandstone under cyclic loading. Chin J Rock Mech Eng 28:2749–2754 (in Chinese)
Fuenkajorn K, Phueakphum D (2010) Effects of cyclic loading on mechanical properties of maha sarakham salt. Eng Geol 112(1):43–52. https://doi.org/10.1016/j.enggeo.2010.01.002
Ge XR (2008) Deformation control law of rock fatigue, real-time X-ray CT scan of geotechnical testing, and new method of stability analysis of slopes and dam foundation. Chin J Geotech Eng 30(1):1–20 (in Chinese)
Ge XR, Jiang Y, Lu YD, Ren JX (2003) Testing study on fatigue deformation law of rock under cyclic loading. Chin J Rock Mech Eng 22(10):1581–1585 (in Chinese)
Geranmayeh VR, Ferdosi B, Okoth AD, Kuek B (2018) Strength degradation of sandstone and granodiorite under uniaxial cyclic loading. J Rock Mech Geotech Eng 10:117–126. https://doi.org/10.1016/j.jrmge.2017.09.005
Haimson BC (1978) Effect of cyclic loading on rock. Dyn Geotech Test. https://doi.org/10.1520/STP35679S
Haimson BC, Heins RW (1972) Aspects of mechanical behavior of rock under static and cyclic loading: part b—mechanical behavior of rock under cyclic loading. Adv Res Projects Agency Bureau Mines
International Society for Rock Mechanics (ISRM) (2007) The complete ISRM suggested methods for rock characterization, testing and monitoring: 1974–2006. In: Ulusay R, Hudson JA (eds.) Suggested methods prepared by the commission on testing methods. ISRM, compilation arranged by the ISRM Turkish National Group, Kozan Ofset, Ankara, Turkey
Ishizuka Y, Abe T, Kodama J (1990) Fatigue behaviour of granite under cyclic loading. In: Butler AG, Franklin, JA (eds.), In: Proc ISRM international symposium on static and dynamic considerations in rock engineering, Publ Rotterdam, A A Balkema, p. 139–46
Khandelwal M, Ranjith PG (2013) Behaviour of brittle material in multiple loading rates under uniaxial compression. Geotech Geol Eng 31:1305–1315. https://doi.org/10.1007/s10706-013-9651-5
Khandelwal M, Ranjith PG (2017) Study of crack propagation in concrete under multiple loading rates by acoustic emission. Geomech Geophys Geo-Energ Geo-Resour 3:393–404. https://doi.org/10.1007/s40948-017-0067-1
Khandelwal M, Ranjith PG, Pan Z, Sanjayan JG (2013) Effect of strain rate on strength properties of low-calcium fly-ash-based geopolymer mortar under dry condition. Arab J Geosci 6:2383–2389. https://doi.org/10.1007/s12517-011-0507-0
Kodama J, Ishizuka Y, Abe T, Ishijima Y, Goto T (2000) Estimation of the fatigue strength of granite subjected to long-period cyclic loading. Shigen-to-Sozai 116:111–118
Lee JU, Rhee CG, Kim IJ, Kim YS (1992) A study on the fatigue failure behavior of cheon-ho mt. limestone under cyclic loading. Nucl Eng Technol 24(2):98–109
Liu EL, He SM (2012) Effects of cyclic dynamic loading on the mechanical properties of intact rock samples under confining pressure conditions. Eng Geol 125:81–91. https://doi.org/10.1016/j.enggeo.2011.11.007
Liu EL, Huang RQ, He SM (2012) Effects of frequency on the dynamic properties of intact rock samples subjected to cyclic loading under confining pressure conditions. Rock Mech Rock Eng 45(1):89–102. https://doi.org/10.1007/s00603-011-0185-y
Ma LJ, Liu XY, Wang MY, Xu HF, Hua RP, Fan PX, Jiang SR, Wang GA, Yi QK (2013) Experimental investigation of the mechanical properties of rock salt under triaxial cyclic loading. Int J Rock Mech Min Sci 62:34–41. https://doi.org/10.1016/j.ijrmms.2013.04.003
Momeni A, Karakus M, Khanlari GR, Heidari M (2015) Effects of cyclic loading on the mechanical properties of a granite. Int J Rock Mech Min Sci 77:89–96. https://doi.org/10.1016/j.ijrmms.2015.03.029
Petros V, Bagde MN, Holub K, Michalcik P (2003) Comparison of changes in the strength and the deformation behavior of rocks under static and dynamic loading. ISRM 2003–Technology roadmap for rock mechanics, South African Institute of Mining and Metallurgy, p. 899–902
Ren S, Bai YM, Zhang JP, Jiang DY, Yang CH (2013) Experimental investigation of the fatigue properties of salt rock. Int J Rock Mech Min Sci 64:68–72. https://doi.org/10.1016/j.ijrmms.2013.08.023
Seyed MD, Peter V, Balázs V (2020) Investigation of the relationship between dynamic and static deformation moduli of rocks. Geomech Geophys Geo-Energ Geo-Resour 6:29. https://doi.org/10.1007/s40948-020-00155-z
Shi CH, Ding ZD, Lei MF, Li MP (2014) Accumulated deformation behavior and computational model of water-rich mudstone under cyclic loading. Rock Mech Rock Eng 47(4):1485–1491. https://doi.org/10.1007/s00603-013-0427-2
Singh SK (1989) Fatigue and strain hardening behaviour of graywacke from the flagstaff formation. New South Wales Eng Geol 26(2):171–179. https://doi.org/10.1016/0013-7952(89)90005-7
Taheri A, Royle A, Yang Z, Zhao Y (2016) Study on variations of peak strength of a sandstone during cyclic loading. Geomech Geophys Geo-energ Geo-resour 2:1–10
Tao ZY, Mo HH (1990) An experimental study and analysis of the behaviour of rock under cyclic loading. Int J Rock Mech Min Sci 27(1):51–56. https://doi.org/10.1016/0148-9062(90)90008-P
Tien YM, Lee DH, Juang CH (1990) Strain, pore pressure and fatigue characteristics of sandstone under various load conditions. Int J Rock Mech Min Sci 27(4):283–289. https://doi.org/10.1016/0148-9062(90)90530-f
Wang YS, Ma LJ, Fan PX, Chen Y (2016) A fatigue damage model for rock salt considering the effects of loading frequency and amplitude. Int J Min Sci Technol 26(5):955–958. https://doi.org/10.1016/j.ijmst.2016.05.054
Wang SM, Liu YS, Du K, Zhou J, Khandelwal M (2020) Waveform features and failure patterns of hollow cylindrical sandstone specimens under repetitive impact and triaxial confinements. Geomech Geophys Geo-Energy Geo-Resour 6(4):57. https://doi.org/10.1007/s40948-020-00183-9
Wang S, Xiong X, Liu Y, Zhou J, Du K, Cui Y, Khandelwal M (2021) Stress–strain relationship of sandstone under confining pressure with repetitive impact. Geomech Geophys Geo-Energy Geo-Resour 7(2):39. https://doi.org/10.1007/s40948-021-00250-9
Xia KZ, Chen CX, Zheng Y, Zhang H, Liu XM, Deng YY, Yang KY (2019) Engineering Geology and ground collapse mechanism in the Chengchao Iron-ore Mine in China. Eng Geol 249:129–147. https://doi.org/10.1016/j.enggeo.2018.12.028
Xiao JQ, Ding DX, Xu G, Jiang FL (2009) Inverted s-shaped model for nonlinear fatigue damage of rock. Int J Rock Mech Min Sci 46(3):643–648. https://doi.org/10.1016/j.ijrmms.2008.11.002
Xiao JQ, Ding DX, Jiang FL, Xu G (2010a) Fatigue damage variable and evolution of rock subjected to cyclic loading. Int J Rock Mech Min Sci 47(3):461–468. https://doi.org/10.1016/j.ijrmms.2009.11.003
Xiao JQ, Ding DX, Xu G, Jiang FL (2010b) Deformation characteristics of rock under constant amplitude cyclic loading. J Cent South Univ Sci Technol 41(2):685–691 (in Chinese)
Xu J, Li SC, Tao YQ, Tang XJ, Wu X (2009) Acoustic emission characteristic during rock fatigue damage and failure. Procedia Earth Planet Sci 1:556–559. https://doi.org/10.1016/j.proeps.2009.09.088
Yamashita S, Sugimoto F, Imai T, Namsrai D, Yamauchi M, Kamoshida N (2003) The relationship between the failure process of the creep or fatigue test and of the conventional compression test on rock. Diabetes Res Clin Pract 60(3):191–197
Yang SQ, Xu P, Xu T (2015) Nonlinear visco-elastic and accelerating creep model for coal under conventional triaxial compression. Geomech Geophys Geo-Energ Geo-Resour 1:109–120. https://doi.org/10.1007/s40948-015-0014-y
Yang SQ, Yang J, Xu P (2020) Analysis on pre-peak deformation and energy dissipation characteristics of sandstone under triaxial cyclic loading. Geomech Geophys Geo-Energ Geo-Resour. https://doi.org/10.1007/s40948-020-00146-0
Zhang QX, Ge XR, Huang M, Sun H (2006) Testing study on fatigue deformation law of red sandstone under triaxial compression with cyclic loading. Chin J Rock Mech Eng 25(03):473–478 (in Chinese)
Zhou J, Li X, Mitri HS (2015) Comparative performance of six supervised learning methods for the development of models of hard rock pillar stability prediction. Nat Hazards 79(1):291–316. https://doi.org/10.1007/s11069-015-1842-3
Zhou J, Li X, Mitri HS (2018) Evaluation method of rockburst: state-of-the-art literature review. Tunn Undergr Space Technol 81:632–659
Acknowledgements
This paper was supported by the National Natural Science Foundation of China (Grant Nos. 51774326, 11772357 and 41807259), as well as by the Open Fund of Mining Disaster Prevention and Control Ministry Key Laboratory at Shandong University of Science and Technology (Grant No. MDPC201917).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declared that they have no conflicts of interest to this work. We declare that we do not have any commercial or associative interest that represents a conflict of interest in connection with the work submitted.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Du, K., Sun, Y., Zhou, J. et al. Low amplitude fatigue performance of sandstone, marble, and granite under high static stress. Geomech. Geophys. Geo-energ. Geo-resour. 7, 68 (2021). https://doi.org/10.1007/s40948-021-00266-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40948-021-00266-1