Skip to main content

Finite Element Analysis of the Biomechanical Effect of Bone Resection Depth in the Distal Tibia after Total Ankle Replacement

Abstract

Purpose

Correct resection of the tibial bone in total ankle replacement (TAR) procedure is crucial for accurate TAR implant positioning and the avoidance of post-operative complications. However, the biomechanical influence of the resection depth of tibial bone for TAR is not clearly understood. Therefore, the objective of this study is to investigate the biomechanical characteristics of the distal tibia with different resection depths after primary TAR.

Methods

Tibial bone models of eight healthy volunteers (age 27 ± 3.83 years old, 5 Males and 3 females) were constructed and 6 to 16 mm resection depths of each bone were performed under the guidance of senior foot and ankle surgeons. A 4 mm tibial plate was reversed engineering to completely cover the bone resection surface. And finite element analyses were performed to evaluate the biomechanical behavior of these models. 5.2 times of body weight was applied as a worst-case scenario loading condition and element-based material assignment was used for the tibial bone. The resection surface area, resection volume, von Mises stress, and strain at each resection surface were analyzed.

Results

As bone resection depth increased from 6 to 16 mm, the resection surface area decreased from 1125.25\(\pm\)99.76 \({\text{m}\text{m}}^{2}\)to 889.27\(\pm\)101.08 \({\text{m}\text{m}}^{2}\), while the resection volume increased from 14701\(\pm\)4376.30 \({\text{m}\text{m}}^{3}\) to 25116\(\pm\)3354.27 \({\text{m}\text{m}}^{3}\). The biomechanical simulation results showed average von Mises stress increased from 3.46\(\pm\)1.06 MPa to 3.85\(\pm\)0.43 MPa. The average strain increased with the resection depth, from 5.11\(\pm\)1.577 microstrain to 5.68\(\pm\)1.87 microstrain (reach the highest points at 8 to 10 mm resection depth), then decreased to 4.62\(\pm\)1.26 microstrain. Both the stress and strain were mainly distributed peripherally.

Conclusion

As the resection depth was increased in the tibia during TAR, the resection surface area decreased but the resection volume and stress at the surface increased. The strain at the resection surface increased first and then decreased which reached a plateau at 8 to 10 mm resection depth. The 8 to 10 mm above the tibial plafond may be the weakest region of bone support in the distal tibia, which should be avoided in the design tibial component for TAR.

This is a preview of subscription content, access via your institution.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6

Data Availability

The datasets supporting the conclusions of this article are included within the article and its Supplementary Material.

Abbreviations

TAR:

Total Ankle Replacement.

CT:

CT:Computed Tomography.

MPa:

Megapascals.

STL:

Stereolithography.

FDA:

Food and Drug Administration.

3D:

Three-dimensional.

References

  1. Zhao, D., Huang, D., Zhang, G., Wang, X., Zhang, T., & Ma, X. (2020). Positive and negative factors for the treatment outcomes following total ankle arthroplasty? A systematic review. Foot And Ankle Surgery, Jan;26(1), 1–13. https://doi.org/10.1016/j.fas.2018.12.003

    Article  Google Scholar 

  2. Gross, C. E., Palanca, A. A., & DeOrio, J. K. (2018). Design Rationale for Total Ankle Arthroplasty Systems: An Update. Journal of the American Academy of Orthopaedic Surgeons, 26(10), 353–359. https://doi.org/10.5435/JAAOS-D-16-00715

    Article  PubMed  Google Scholar 

  3. Integra LifeSciences (2021). -03-01) CADENCE Total Ankle System Surgical Technique. from https://cadenceankle.com/

  4. STAR total ankle system operative technique from https://footankle.stryker.com/en/products/total-ankle-replacements/star-ankle

  5. Wright Medical Group N.V. INBONE II total ankle system surgical technique. from http://www.totalankleinstitute.com/INBONE-Products/INBONE-ANKLE/

  6. Wright Medical Group N.V. INFINITY Total Ankle System Surgical technique. from http://www.totalankleinstitute.com/INFINITY-Products/INFINITY-ANKLE/

  7. Hvid, I., Rasmussen, O., Jensen, N. C., & Nielsen, S. (1985). Trabecular bone strength profiles at the ankle joint. Clinical Orthopaedics And Related Research, 199, 306–312

    Article  Google Scholar 

  8. Bischoff, J. E., Schon, L., & Saltzman, C. (2017). Influence of Geometry and Depth of Resections on Bone Support for Total Ankle Replacement. Foot & ankle international, 38(9), 1026–1034. https://doi.org/10.1177/1071100717712508

    Article  Google Scholar 

  9. Zhang, Q. H., Cossey, A., & Tong, J. (2016). Stress shielding in periprosthetic bone following a total knee replacement: Effects of implant material, design and alignment. Medical Engineering & Physics, 38(12), 1481–1488. https://doi.org/10.1016/j.medengphy.2016.09.018

    Article  Google Scholar 

  10. Lee, R. W., Volz, R. G., & Sheridan, D. C. (1991). The role of fixation and bone quality on the mechanical stability of tibial knee components.Clin Orthop Relat Res(273):177–183

  11. Wang, S., Wang, B., Lan, X., Xu, Z., Huang, H., Wang, X. … Ma, J. (2021). Application of a Personalized Finite Element Analysis and 3D-Printed Navigation Template in the Treatment of Femoral Neck Fracture with Cannulated Screw. Journal of Medical and Biological Engineering, 41(6), 934–941. https://doi.org/10.1007/s40846-021-00667-3

    Article  Google Scholar 

  12. Xu, J. H., Tu, Z. X., Xu, J. X., Zhang, S. Y., & Tan, J. R. (2021). Biomechanical Strengthening Design for Limb Articulation Based on Reconstructed Skeleton Kinesthetics. Journal of Medical and Biological Engineering, 41(5), 715–729. https://doi.org/10.1007/s40846-021-00645-9

    Article  Google Scholar 

  13. Terrier, A., Larrea, X., Guerdat, J., & Crevoisier, X. (2014). Development and experimental validation of a finite element model of total ankle replacement. Journal of Biomechanics, 47(3), 742–745. https://doi.org/10.1016/j.jbiomech.2013.12.022

    Article  PubMed  Google Scholar 

  14. Sopher, R. S., Amis, A. A., Calder, J. D., & Jeffers, J. R. T. (2017). Total ankle replacement design and positioning affect implant-bone micromotion and bone strains. Medical Engineering & Physics, 42, 80–90. https://doi.org/10.1016/j.medengphy.2017.01.022

    Article  Google Scholar 

  15. Zhao, D. H., Huang, D. C., Zhang, G. H., Fan, Y. P., & Ma, X. (2019). Talar Dome Investigation and Talocrural Joint Axis Analysis Based on Three-Dimensional (3D) Models: Implications for Prosthetic Design. BioMed Research International, 2019, 1–10. https://doi.org/10.1155/2019/8634159

    CAS  Article  Google Scholar 

  16. Linde, F., Hvid, I., & Madsen, F. (1992). The effect of specimen geometry on the mechanical behaviour of trabecular bone specimens. Journal of Biomechanics, 25(4), 359–368

    CAS  Article  Google Scholar 

  17. Carter, D. R., & Hayes, W. C. (1977). The compressive behavior of bone as a two-phase porous structure.JBJS, 59(7)

  18. Mondal, S., & Ghosh, R. (2019). The Effects of Implant Orientations and Implant–Bone Interfacial Conditions on Potential Causes of Failure of Tibial Component Due to Total Ankle Replacement. Journal of Medical and Biological Engineering, 39(4), 541–551. https://doi.org/10.1007/s40846-018-0435-5

    Article  Google Scholar 

  19. Linde, F., Hvid, I., & Madsen, F. (1992). The effect of specimen geometry on the mechanical behaviour of trabecular bone specimens. Journal of Biomechanics, 25(4), 359–368. https://doi.org/10.1016/0021-9290(92)90255-Y

    CAS  Article  PubMed  Google Scholar 

  20. Mondal, S., & Ghosh, R. (2017). A numerical study on stress distribution across the ankle joint: Effects of material distribution of bone, muscle force and ligaments. Journal of orthopaedics, 14(3), 329–335. https://doi.org/10.1016/j.jor.2017.05.003

    Article  PubMed  PubMed Central  Google Scholar 

  21. Seireg, A., & Arvikar, R. J. (1975). The prediction of muscular load sharing and joint forces in the lower extremities during walking. Journal of Biomechanics, 8(2), 89–102. https://doi.org/10.1016/0021-9290(75)90089-5

    CAS  Article  PubMed  Google Scholar 

  22. FDA SUMMARY OF SAFETY AND EFFECTIVENESS (SSED) of Scandinavian Total Ankle Replacement System (STAR Ankle) from https://www.accessdata.fda.gov/cdrh_docs/pdf5/P050050b.pdf

  23. FDA SUMMARY OF SAFETY AND EFFECTIVENESS DATA (SSED) of Hintermann Series H3 Total Ankle Replacement System from https://www.accessdata.fda.gov/cdrh_docs/pdf16/P160036B.pdf

  24. Tuncer, M., Cobb, J. P., Hansen, U. N., & Amis, A. A. (2013). Validation of multiple subject-specific finite element models of unicompartmental knee replacement. Medical Engineering & Physics, 35(10), 1457–1464. https://doi.org/10.1016/j.medengphy.2013.03.020

    Article  Google Scholar 

  25. Terrier, A., Fernandes, C. S., Guillemin, M., & Crevoisier, X. (2017). Fixed and mobile-bearing total ankle prostheses: Effect on tibial bone strain. Clinical biomechanics (Bristol Avon), 48, 57–62. https://doi.org/10.1016/j.clinbiomech.2017.07.009

    Article  Google Scholar 

Download references

Acknowledgements

None.

Funding

This project was supported by Natural Science Foundation of Shanghai (Grant No. 19ZR1407400), Clinical Research Plan of SHDC (Grant No. SHDC2020CR3071B), and Science and Technology Commission of Shanghai Municipality (Grant No. 21511102200).

Author information

Authors and Affiliations

Authors

Contributions

J.Y. and D.Z. contributed equally. J.Y. and D.Z. performed the finite element analysis, drafted the manuscript and designed the figures. J.Y. and S.W. aided in interpreting the results and worked on the manuscript. S.W., C.Z. and J.H. performed the measurements, X.M. and X.W. were involved in planning and supervised the work. All authors discussed the results and commented on the manuscript.

Corresponding author

Correspondence to Xin Ma.

Ethics declarations

Ethics approval and consent to participate

This study was approved by the institute’s ethical committee (Approval letter No. 2021 − 457).

Consent for publication

Participants enrolled into the study agreed the use of data for research.

Competing interests

The authors declare that they have no competing interests.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Electronic supplementary material

Below is the link to the electronic supplementary material.

Supplementary Material 1

Supplementary Material 2

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Yu, J., Zhao, D., Wang, S. et al. Finite Element Analysis of the Biomechanical Effect of Bone Resection Depth in the Distal Tibia after Total Ankle Replacement. J. Med. Biol. Eng. (2022). https://doi.org/10.1007/s40846-022-00722-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s40846-022-00722-7

Keywords

  • Total ankle replacement
  • Total ankle arthroplasty
  • Finite element analysis
  • Biomechanics
  • Tibial bone resection depth