Abstract
The acceleration of environmental pollution and global warming has resulted in increased environmental awareness and regulations to reduce carbon emissions. As the automotive industry is evolving from internal combustion engine (ICE) vehicles to electric vehicles (EVs) and urban air mobility (UAM), composites have gained attraction for increased driving range and green mobility. However, composites, acclaimed to be an alternative to metals for its reduced weight and high mechanical properties, have not achieved successful mass adoption due to the tradeoff in performance and cost. While legislation is continuously being updated to tackle environmental concerns, automotive original equipment manufacturers (OEMs) have been hesitant to apply composite technology to mainstream vehicles, largely due to economic reasons. Therefore, latest developments have been focused on application of biodegradable composites and integration of robotic automation into composite manufacturing processes for eco-friendly, sustainable, cost-effective production. This paper reviews the latest applications of composite materials into modern vehicles and evaluates state of the art of composite manufacturing and recycling processes for green mobility.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.References
Kumar, S., & Bharj, R. S. (2018). Emerging composite material use in current electric vehicle: a review. Materials Today: Proceedings, 5(14 Part 2), 27946–27954. Accessed Sept 2022
Schulze, A., Paul MacDuffie, J., & Täube, F. A. (2015). Introduction: knowledge generation and innovation diffusion in the global automotive industry—change and stability during turbulent times. Industrial and Corporate Change, 24(3), 603–611. Accessed Sept 2022
Garrow, L. A., German, B. J., & Leonard, C. E. (2021). Urban air mobility: a comprehensive review and comparative analysis with autonomous and electric ground transportation for informing future research. Transportation Research Part C: Emerging Technologies, 132, 103377. Accessed Sept 2022.
Pejman, R., Gorman, J., & Najafi, A. R. (2022). Multi-physics design of a new battery packaging for electric vehicles utilizing multifunctional composites. Composites Part B: Engineering, 237, 109810. Accessed Sept 2022.
Lukin, E., Krajnović, A., & Bosna, J. (2022). Sustainability strategies and achieving sdgs: a comparative analysis of leading companies in the automotive industry. Sustainability, 14(7), 4000. Accessed Sept 2022.
Transport could burn up the EU’s entire carbon budget - International Council on Clean Transportation. 2021 2021–04–09; Available from: https://theicct.org/transport-could-burn-up-the-eus-entire-carbon-budget/. Accessed Sept 2022.
Elgowainy, A., et al. (2018). Current and future United States light-duty vehicle pathways: cradle-to-grave lifecycle greenhouse gas emissions and economic assessment. Environmental Science & Technology, 52(4), 2392–2399. Accessed Sept 2022.
Tanaka, K., et al. (2021). Cost-effective implementation of the Paris agreement using flexible greenhouse gas metrics. Science Advances, 7(22), eabf020. Accessed Sept 2022.
Tol, R. S. (2021). Europe’s climate target for 2050: an assessment. Intereconomics, 56(6), 330–335. Accessed Sept 2022.
Sloan, J. (2022). Composites end markets: Automotive (2022). Available from: https://www.compositesworld.com/articles/composites-end-markets-automotive-2022. Accessed Sept 2022.
Yorseng, K., et al. (2022). Towards green composites: bioepoxy composites reinforced with bamboo/basalt/carbon fabrics. Journal of Cleaner Production, 363, 132314. Accessed Sept 2022.
Rangappa, S. M., et al. (2022). Bioepoxy based hybrid composites from nano-fillers of chicken feather and lignocellulose Ceiba Pentandra. Scientific Reports, 12(1), 1–18. Accessed Sept 2022.
Sarfraz, M. S., Hong, H., & Kim, S. S. (2021). Recent developments in the manufacturing technologies of composite components and their cost-effectiveness in the automotive industry: a review study. Composite Structures, 266, 113864. Accessed Sept 2022.
Bhandari, B., et al. (2011). Development of CFRP precision gantry beams for 11th generation LCD panel manufacturing. In: ICCM International Conferences on Composite Materials. Accessed Sept 2022.
Kim, C., Yun, M. G., Kim, S., & Jeon, G. W. (2022). Mathematical Model to Predict the Moduli of Wet-Laid Pulp/Fiber/Resin Composite Materials. International Journal of Precision Engineering and Manufacturing, 23(11), 1315–1324. https://doi.org/10.1007/s12541-022-00700-8. Accessed Sept 2022.
Loeliger, A., Yang, E., & Bomphray, I. (2021). An overview of automated manufacturing for composite materials. In: 2021 26th international conference on automation and computing (ICAC). Accessed Sept 2022.
Rajak, D. K., et al. (2019). Recent progress of reinforcement materials: a comprehensive overview of composite materials. Journal of Materials Research and Technology, 8(6), 6354–6374. Accessed Sept 2022.
Composites Market Size | Industry Report, 2021–2028. 2022; Available from: https://www.grandviewresearch.com/industry-analysis/composites-market. Accessed Sept 2022.
Nagavally, R. R. (2017). Composite materials-history, types, fabrication techniques, advantages, and applications. Int. J. Mech. Prod. Eng, 5(9), 82–87. Accessed Sept 2022.
Frost, S. and A. Sullivan. (2009). Global analysis of weight reduction strategies of major OEMs. Market Engineering Research. https://store.frost.com/global-analysis-of-weight-reduction-strategies-of-major-oems.html. Accessed Sept 2022.
Friedrich, K., & Almajid, A. (2012). Manufacturing aspects of advanced polymer composites for automotive applications. Applied Composite Materials., 20, 107–128. Accessed Sept 2022.
Biron, M. (2018). Thermoplastics and thermoplastic composites. Elsevier. Accessed Sept 2022.
Murray, R. E., et al. (2021). Structural validation of a thermoplastic composite wind turbine blade with comparison to a thermoset composite blade. Renewable Energy, 164, 1100–1107. Accessed Sept 2022.
Ramirez-Tejeda, K., Turcotte, D. A., & Pike, S. (2017). Unsustainable wind turbine blade disposal practices in the United States: a case for policy intervention and technological innovation. NEW SOLUTIONS: A Journal of Environmental and Occupational Health Policy, 26(4), 581–598. Accessed Sept 2022.
Galve, J. E., Elduque, D., Pina, C., & Javierre, C. (2022). Life Cycle Assessment of a Plastic Part Injected with Recycled Polypropylene: A Comparison with Alternative Virgin Materials. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(3), 919–932. https://doi.org/10.1007/s40684-021-00363-2. Accessed Sept 2022.
Yun, Y. S., & Kim, J. C. (2021). Reducing Curve Squeal Noise Using Composite Materials Based on Experimental Investigation. International Journal of Precision Engineering and Manufacturing, 22(9), 1573–1582. https://doi.org/10.1007/s12541-021-00540-y. Accessed Sept 2022.
Seo J, Kim DY, Kim DC, Park HW (2021) Recent Developments and Challenges on Machining of Carbon Fiber Reinforced Polymer Composite Laminates. International Journal of Precision Engineering and Manufacturing 22(12) 2027-2044. https://doi.org/10.1007/s12541-021-00596-w. Accessed Sept 2022.
Huda, M. S., et al. (2008). Natural-fiber composites in the automotive sector. In K. L. Pickering (Ed.), Properties and Performance of natural-fibre composites (pp. 221–268). Woodhead Publishing. Accessed Sept 2022.
Zhao, X., et al. (2022). Recycling of natural fiber composites: challenges and opportunities. Resources, Conservation and Recycling, 177, 105962. Accessed Sept 2022.
Pandey, J. K., et al. (2012). An overview on the cellulose based conducting composites. Composites Part B: Engineering, 43(7), 2822–2826. Accessed Sept 2022.
Pervaiz, M., et al. (2016). Emerging trends in automotive lightweighting through novel composite materials. Materials Sciences and Applications, 7(01), 26. Accessed Sept 2022.
Pandey, J. K., et al. (2012). Preparation and properties of cellulose-based nano composites of clay and polypropylene. Journal of Applied Polymer Science, 125(S1), E651–E660. Accessed Sept 2022.
Pandey, J. K., et al. (2010). Recent advances in the application of natural fiber based composites. Macromolecular Materials and Engineering, 295(11), 975–989. Accessed Sept 2022.
Frketic, J., Dickens, T., & Ramakrishnan, S. (2017). Automated manufacturing and processing of fiber-reinforced polymer (FRP) composites: An additive review of contemporary and modern techniques for advanced materials manufacturing. Additive Manufacturing, 14, 69–86. Accessed Sept 2022.
Composite and speciality materials for Urban Air Mobility. 2020; Available from: https://www.solvay.com/sites/g/files/srpend221/files/2020-12/Composite-UAM.pdf. Accessed Sept 2022.
Holmes, M. (2014). Continued growth for European GRP market. Reinforced Plastics, 58(6), 28–30. Accessed Sept 2022.
Ali, N., & Hoque, M. E. (2022). Bionanocomposites in the automotive and aerospace applications. Polymer based bio-nanocomposites (pp. 237–253). Springer.
C., Tezara M., Zalinawati J. P., Siregar J., Jaafar M. H. M., Hamdan A. N., Oumer K. H., Chuah,. (2022). Effect of Stacking Sequences Fabric Orientations and Chemical Treatment on the Mechanical Properties of Hybrid Woven Jute-Ramie Composites. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(1), 273–285. https://doi.org/10.1007/s40684-021-00311-0. Accessed Sept 2022.
Huda, M.K. and I. Widiastuti. (2021). Natural fiber reinforced polymer in automotive application A systematic literature review. In Journal of Physics: Conference Series. IOP Publishing. Accessed Sept 2022.
Malnati, P. (2021). Riding pretty: Hybrid upper control arms move to pickups. Available from: https://www.compositesworld.com/articles/riding-pretty-hybrid-upper-control-arms-move-to-pickups. Accessed Sept 2022.
DeMattia, N. (2015). Chassis, CFRP & Suspension: 2016 BMW 7 Series. 2015–06–10; Available from: https://www.bmwblog.com/2015/06/10/chassis-cfrp-suspension-2016-bmw-7-series/. Accessed Sept 2022.
Malnati, P. (2020). Composites-intensive masterwork: 2020 Corvette, Part 1. Available from: https://www.compositesworld.com/articles/composites-intensive-masterwork-2020-corvette-part-1. Accessed Sept 2022.
Every gram counts: BMW M Carbon Compound wheels. 2022; Available from: https://www.bmw-m.com/en/topics/magazine-article-pool/every-gram-counts.html. Accessed Sept 2022.
Mitschang, P., & Hildebrandt, K. (2012). Polymer and composite moulding technologies for automotive applications. In J. Rowe (Ed.), Advanced materials in automotive engineering (pp. 210–229). Woodhead Publishing. Accessed Sept 2022.
McConnell, V. P. (2007). SMC has plenty of road to run in automotive applications. Reinforced Plastics, 51(1), 20–25. Accessed Sept 2022.
Starke, J. (2016). Carbon composites in automotive structural applications. EuCIA: Composites and Sustainability. Accessed Sept 2022.
Kim, D.-J., et al. (2021). Design and manufacture of automotive hybrid steel/carbon fiber composite B-pillar component with high crashworthiness. International Journal of Precision Engineering and Manufacturing-Green Technology, 8(2), 547–559. Accessed Sept 2022.
Sloan, J. (2017). Ford assesses SMC/prepreg suspension knuckle to replace metal. Available from: https://www.compositesworld.com/articles/ford-assesses-smcprepreg-suspension-knuckle-to-replace-metallic-predecessor. Accessed Sept 2022.
Gardiner, G. (2017). Hybrid carbon fiber/aluminum suspension knuckle. Accessed Sept 2022.
Nehls, G. (2021). Hexion partners with Rassini for composite leaf spring application in new Ford F-150 mode. Available from: https://www.compositesworld.com/news/hexion-partners-with-rassini-for-composite-leaf-spring-application-in-new-ford-f-150-model. Accessed Sept 2022.
Mason, K. (2020). Composite output shaft ready for automotive proving ground. Accessed Sept 2022.
Winkler, M. (1990). Automotive under-the-hood applications in vinyl ester resin SMC/BMC. SAE transactions. 675–690. Accessed Sept 2022.
Granowicz, P., Molteni, G. L., & Kobayashi, T. (2011). New polymer" SHIELD" technology protects high-performance nylon and ppa polymers to replace more metal-for weight and cost savings-under the hood. SAE International Journal of Materials and Manufacturing, 4(1), 430–439. Accessed Sept 2022.
Dev, V.S., Angadi, S., & Roy, S. (2002). Forming and modal analysis of sheet metal oil pan. SAE Technical Paper. Accessed Sept 2022.
Malnati, P. (2011). Under the hood: Thermoplastics tackle tough jobs. https://www.compositesworld.com/articles/under-the-hood-thermoplastics-tackle-tough-jobs. Accessed Sept 2022.
Mike, & Brady, P. (2010). Technology developments in automotive composites. Reinforced Plastics, 54(6), 25–29. Accessed Sept 2022.
Sanyang, M. L., et al. (2016). Recent developments in sugar palm (Arenga pinnata) based biocomposites and their potential industrial applications: a review. Renewable and Sustainable Energy Reviews, 54, 533–549. Accessed Sept 2022.
Puglia, D., Biagiotti, J., & Kenny, J. M. (2005). A review on natural fibre-based composites—Part II. Journal of Natural Fibers, 1(3), 23–65. Accessed Sept 2022.
Manolis, S.L. (1999). Natural fibers: the new fashion in automotive plastics. Plastics Technol. p. 62–68. Accessed Sept 2022.
Malnati, P. (2010). Interior innovation: The value proposition. Available from: https://www.compositesworld.com/articles/interior-innovation-the-value-proposition. Accessed Sept 2022.
High Performance Carbon Fiber Wheels. World First One-Piece Carbon Fiber | Carbon Revolution. 2022. Available from: https://www.carbonrev.com/. Accessed Sept 2022.
Sloan, J. (2022). Shelby GT350R features carbon fiber wheels. Available from: https://www.compositesworld.com/news/shelby-gt350r-features-carbon-fiber-wheels.
Vision Wheel. 2022; Available from: http://www.visionwheel.com/. Accessed Sept 2022.
Dhoke, A., & Dalavi, A. (2021). A critical review on lightweight design of battery pack enclosure for electric vehicles. International Journal of Sustainable Transportation Technology, 4(2), 53–62. Accessed Sept 2022.
Mason, H. (2021). Designing a versatile, multi-material EV battery enclosure. Available from: https://www.compositesworld.com/articles/designing-a-versatile-multi-material-ev-battery-enclosure. Accessed Sept 2022.
Sloan, J. (2021). Evonik-led group targets epoxy SMC for EV battery housings. Available from: https://www.compositesworld.com/articles/evonik-led-group-targets-epoxy-smc-for-ev-battery-housings. Accessed Sept 2022.
Zhou, H., et al. (2022). Structural composite energy storage devices — a review. Materials Today Energy, 24, 100924. Accessed Sept 2022.
Xu, Y., et al. (2021). High-performance structural supercapacitors based on aligned discontinuous carbon fiber electrodes and solid polymer electrolytes. ACS Applied Materials & Interfaces, 13(10), 11774–11782. Accessed Sept 2022.
Pandey, D., et al. (2022). Energized composites for electric vehicles: a dual function energy-storing supercapacitor-based carbon fiber composite for the body panels. Small (Weinheim an der Bergstrasse, Germany), 18(9), 2107053. Accessed Sept 2022.
Hubert, P., et al. (2018). Out-of-autoclave prepreg processing. Elsevier. Accessed Sept 2022.
Crump, D. A., Dulieu-Barton, J. M., & Savage, J. (2010). The manufacturing procedure for aerospace secondary sandwich structure panels. Journal of Sandwich Structures & Materials, 12(4), 421–447. Accessed Sept 2022.
Hubert, P., Fernlund, G., & Poursartip, A. (2012). Autoclave processing for composites. Manufacturing techniques for polymer matrix composites (PMCs) (pp. 414–434). Elsevier. Accessed Sept 2022.
Hjellming, L. N., & Walker, J. S. (1989). Thermal curing cycles for composite cylinders with thick walls and thermoset resins. Journal of Composite Materials, 23(10), 1048–1064. Accessed Sept 2022.
Mahdavi, S. (2017). Thermal cycling of out‐of‐autoclave thermosetting composite materials. Concordia University. Accessed Sept 2022.
Sloan, J. (2016). Taking the hand out of hand layup. Available from: https://www.compositesworld.com/articles/taking-the-hand-out-of-hand-layup. Accessed Sept 2022.
Dirk, H.-J.L., Ward, C., & Potter, K. D. (2012). The engineering aspects of automated prepreg layup: history, present and future. Composites Part B: Engineering, 43(3), 997–1009. Accessed Sept 2022.
Elkington, M.P., Ward, C.,& Potter, K.D. (2016). Automated layup of sheet prepregs on complex moulds. in SAMPE Long Beach 2016. Accessed Sept 2022.
Lukaszewicz, D.H.-J.A. (2011). Optimisation of high-speed automated layup of thermoset carbon-fibre preimpregnates. University of Bristol. Accessed Sept 2022.
Karlsson, K. F., & TomasÅström, B. (1997). Manufacturing and applications of structural sandwich components. Composites Part A: Applied Science and Manufacturing, 28(2), 97–111. Accessed Sept 2022.
Perna, A. S., et al. (2019). Manufacturing of a metal matrix composite coating on a polymer matrix composite through cold gas dynamic spray technique. Journal of Materials Engineering and Performance, 28(6), 3211–3219. Accessed Sept 2022.
Zin, M. H., et al. (2019). Automated spray up process for pineapple leaf fibre hybrid biocomposites. Composites Part B: Engineering, 177, 107306. Accessed Sept 2022.
Hamidi, Y.K. & Altan, M.C. (2016). Process induced defects in resin transfer molded composites. Accessed Sept 2022.
Vita, A., et al. (2019). Comparative life cycle assessment of low-pressure RTM, compression RTM and high-pressure RTM manufacturing processes to produce CFRP car hoods. Procedia CIRP, 80, 352–357. Accessed Sept 2022.
Baskaran, M., et al. Manufacturing cost comparison of RTM, HP-RTM and CRTM for an automotive roof. In: Proceedings of the 16th European Conference on Composite Materials, ECCM. 2014. Accessed Sept 2022.
Davenport, D. E., Petrovich, R., & Sutton, G. (2007). Low pressure resin transfer molding for cost effective aircraft quality structures. Cleveland OH: North Coast Composites. Accessed Sept 2022.
Du, R. K., et al. (2013). Flow simulation and optimization of the car bumper beam by VARTM process. Advanced Materials Research., 753, 236–240. Accessed Sept 2022.
Kang, M., Lee, W., & Hahn, H. (2001). Analysis of vacuum bag resin transfer molding process. Composites Part A: Applied science and manufacturing, 32(11), 1553–1560. Accessed Sept 2022.
Nehls, G. Carbon fiber automotive parts production industrialized via C-RTM process. 2020; Available from: https://www.compositesworld.com/news/carbon-fiber-automotive-parts-production-industrialized-via-c-rtm-process. Accessed Sept 2022.
Lee, L. J. (1989). 12 - Reaction injection molding. In G. Allen & J. C. Bevington (Eds.), Comprehensive polymer science and supplements (pp. 379–426). Pergamon. Accessed Sept 2022.
Halley, P. J. (2012). Rheology of thermosets: the use of chemorheology to characterise and model thermoset flow behaviour. Thermosets (pp. 92–117). Elsevier. Accessed Sept 2022.
Materials & Processes: Fabrication methods. 2022; Available from: https://www.compositesworld.com/articles/fabrication-methods. Accessed Sept 2022.
Ratna, D. (2022). Thermoset composites. In D. Ratna (Ed.), Recent advances and applications of thermoset resins (2nd ed., pp. 371–418). Elsevier. Accessed Sept 2022.
Meola, C., Boccardi, S., & Carlomagno, G. M. (2016). Infrared thermography in the evaluation of aerospace composite materials: infrared thermography to composites. Woodhead Publishing. Accessed Sept 2022.
Mouritz, A. P. (2012). Introduction to aerospace materials. Elsevier. Accessed Sept 2022.
Frost, M., & Mills, A. (2003). Resin film infusion process of carbon fibre composite automotive body panels. Sampe Journal, 39, 44–49. Accessed Sept 2022.
Cicala, G., et al. (2018). Hybrid composites manufactured by resin infusion with a fully recyclable bioepoxy resin. Composites Part B: Engineering, 132, 69–76. Accessed Sept 2022.
Hindersmann, A. (2019). Confusion about infusion: an overview of infusion processes. Composites Part A: Applied Science and Manufacturing, 126, 105583. Accessed Sept 2022.
Gardiner, G. (2016). Resin Infusion: Taking Off. Composites World. https://www.compositesworld.com/articles/resin-infusion-taking-off. Accessed Sept 2022.
Mazumdar, S. (2001). Composites manufacturing: materials, product, and process engineering. CRC Press. Accessed Sept 2022.
Greene, J. P. (2011). Compression Molding. In J. P. Greene (Ed.), Automotive plastics and composites (pp. 265–278). William Andrew Publishing. Accessed Sept 2022.
Mallick, P. K. (2018). 2.18 Particulate filled and short fiber reinforced polymer composites☆. In P. W. R. Beaumont & C. H. Zweben (Eds.), Comprehensive composite materials II (pp. 360–400). Oxford: Elsevier. Accessed Sept 2022.
Faudree, M. C., Nishi, Y., & Salvia, M. (2022). Increasing impact strength of a short glass fiber compression molded BMC by shortening fibers without change in equipment. Materials, 15(3), 1145. Accessed Sept 2022.
Aurrekoetxea, J., et al. (2006). Failure of multimaterial fusion bonding interface generated during over-injection molding/thermoforming hybrid process. Journal of Applied Polymer Science, 102(1), 261–265. Accessed Sept 2022.
Schuck, I.M. (2012). New processes for mass production of thermoplastic composite lightweight components. In: Proceeding of the 15th European Conference on Composite Materials, Venice, Italy. Accessed Sept 2022.
Gardiner, G. (2014). CAMISMA’s car seat back: Hybrid composite for high volume. Available from: https://www.compositesworld.com/articles/camismas-car-seat-back-hybrid-composite-for-high-volume. Accessed Sept 2022.
Qing, X. P., et al. (2006). Advances in the development of built-in diagnostic system for filament wound composite structures. Composites Science and Technology, 66(11), 1694–1702. Accessed Sept 2022.
Calabro, M. and J. Perret. (1992). History of solid propellant rocket motors at Aerospatiale. In: 28th Joint Propulsion Conference and Exhibit. Accessed Sept 2022.
Gardiner, G. (2018). Filament winding, reinvented. Available from: https://www.compositesworld.com/articles/filament-winding-reinvented. Accessed Sept 2022.
Gardiner, G. (2017). High-speed, 3D winding of large, complex-shaped composites. Available from: https://www.compositesworld.com/articles/high-speed-3d-winding-of-large-complex-shaped-composites. Accessed Sept 2022.
Jochum, M. (2019). Daimler Sustainability Report 2019. 70546 Stuttgart, Germany. Accessed Sept 2022.
Uozumi, T. (2018). Improving filament winding productivity by multiple feeds. In: Design, manufacturing and applications of composites-twelfth joint Canada-Japan workshop on composites. Accessed Sept 2022.
Jois, K.C., et al. (2021). Towpreg-based design and manufacture of multi-supply filament-wound composite pressure vessels. SAMPE neXus 2021. Accessed Sept 2022.
Dawson, D. (2017). Curved pultrusion? No longer an oxymoron. Available from: https://www.compositesworld.com/articles/curved-pultrusion-no-longer-an-oxymoron. Accessed Sept 2022.
Verma, D., et al. (2019). Processing and evaluation of mechanical properties of epoxy-filled E-glass fiber–fly ash hybrid composites. Mechanical and physical testing of biocomposites, fibre-reinforced composites and hybrid composites (pp. 293–306). Elsevier. Accessed Sept 2022.
2018 World Pultrusion Conference: full report. 2018; Available from: https://www.reinforcedplastics.com/content/news/2018-world-pultrusion-conference-full-report/. Accessed Sept 2022.
Gardiner, G. (2018). Pultrusion picks up speed in automotive applications. Available from: https://www.compositesworld.com/articles/pultrusion-picks-up-speed-in-automotive-applications. Accessed Sept 2022.
Goldsworthy, W.(2011). Pulforming. Wiley Encyclopedia of Composites. p. 1–4. Accessed Sept 2022.
Kim, S., et al. (2021). Additive manufacturing of functional microarchitected reactors for energy, environmental, and biological applications. International Journal of Precision Engineering and Manufacturing-Green Technology, 8(1), 303–326. Accessed Sept 2022.
Gao, M., et al. (2022). Integration of additive manufacturing in casting: advances, challenges, and prospects. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(1), 305–322. Accessed Sept 2022.
Fentahun, M. A., & Savas, M. (2018). Materials used in automotive manufacture and material selection using ashby charts. Int. J. Mater. Eng, 8(3), 40–54. Accessed Sept 2022.
Gutowski, T., et al. (2017). Note on the rate and energy efficiency limits for additive manufacturing. Journal of Industrial Ecology, 21(S1), S69–S79. Accessed Sept 2022.
Salifu, S., et al. (2022). Recent development in the additive manufacturing of polymer-based composites for automotive structures—a review. The International Journal of Advanced Manufacturing Technology, 119(11), 6877–6891. Accessed Sept 2022.
Huang, S. H., et al. (2013). Additive manufacturing and its societal impact: a literature review. The International Journal of Advanced Manufacturing Technology, 67(5), 1191–1203. Accessed Sept 2022.
Kim, H. J. (2020). Composite Printer for Carbon/Epoxy Repair. Seoul National University. Accessed Sept 2022.
Huang, Y., et al. (2018). Friction stir welding/processing of polymers and polymer matrix composites. Composites Part A: Applied Science and Manufacturing, 105, 235–257. Accessed Sept 2022.
Jiang, B., Chen, Q., & Yang, J. (2020). Advances in joining technology of carbon fiber-reinforced thermoplastic composite materials and aluminum alloys. The International Journal of Advanced Manufacturing Technology, 110(9), 2631–2649. Accessed Sept 2022.
Maggiore, S., et al. (2021). A review of structural adhesive joints in hybrid joining processes. Polymers, 13(22), 3961. Accessed Sept 2022.
Lambiase, F., et al. (2021). A state-of-the-art review on advanced joining processes for metal-composite and metal-polymer hybrid structures. Materials, 14(8), 1890. Accessed Sept 2022.
Brockmann, W., et al. (2008). Adhesive bonding: materials, applications and technology. John Wiley & Sons. Accessed Sept 2022.
Lee, C.-J., et al. (2014). Design of hole-clinching process for joining of dissimilar materials–Al6061-T4 alloy with DP780 steel, hot-pressed 22MnB5 steel, and carbon fiber reinforced plastic. Journal of Materials Processing Technology, 214(10), 2169–2178. Accessed Sept 2022.
Wang, J., et al. (2021). A self-piercing riveting method for joining of continuous carbon fiber reinforced composite and aluminum alloy sheets. Composite Structures, 259, 113219. Accessed Sept 2022.
Slattery, E. (2017). Friction Lap Spot Joining of Aluminium Alloy 6082-T6 to Carbon Fibre-Reinforced Polyetheretherketone. Accessed Sept 2022.
Pramanik, A., et al. (2017). Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys – a review. Composites Part A: Applied Science and Manufacturing, 101, 1–29. Accessed Sept 2022.
Wagner, G., Balle, F., & Eifler, D. (2013). Ultrasonic welding of aluminum alloys to fiber reinforced polymers. Advanced Engineering Materials, 15(9), 792–803. Accessed Sept 2022.
Yu, G., et al. (2009). Research on key issues of laser welding of dissimilar metal. Chin J Las, 36(2), 261–268. Accessed Sept 2022.
Midling, O. T., & Grong, Ø. (1994). A process model for friction welding of AlMgSi alloys and AlSiC metal matrix composites—I. Haz temperature and strain rate distribution. Acta Metallurgica et Materialia., 42(5), 1595–1609. Accessed Sept 2022.
Wong, K., et al. (2017). Composites recycling solutions for the aviation industry. Science China Technological Sciences, 60(9), 1291–1300. Accessed Sept 2022.
Zhang, J., et al. (2020). Current status of carbon fibre and carbon fibre composites recycling. Composites Part B: Engineering, 193, 108053. Accessed Sept 2022.
Krauklis, A. E., et al. (2021). Composite material recycling technology—state-of-the-art and sustainable development for the 2020s. Journal of Composites Science, 5(1), 28. Accessed Sept 2022.
Zhang, X., M. Yamauchi, and J. Takahashi. (2011). Life cycle assessment of CFRP in application of automobile. In: The 18th international conference on composite materials. South Korea. Accessed Sept 2022.
Zhao, X., et al. (2022). Plastic waste upcycling toward a circular economy. Chemical Engineering Journal, 428, 131928. Accessed Sept 2022.
Krzywiński, K., Sadowski, Ł., Stefaniuk, D., Obrosov, A., & Weiß, S. (2022). Engineering and Manufacturing Technology of Green Epoxy Resin Coatings Modified with Recycled Fine Aggregates. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(1), 253–271. https://doi.org/10.1007/s40684-021-00377-w. Accessed Sept 2022.
Evens, T., et al. (2019). The influence of mechanical recycling on properties in injection molding of fiber-reinforced polypropylene. International Polymer Processing, 34(4), 398–407. Accessed Sept 2022.
Colucci, G., et al. (2015). The effect of mechanical recycling on the microstructure and properties of PA66 composites reinforced with carbon fibers. Journal of Applied Polymer Science. 132(29). Accessed Sept 2022.
López, F. A., et al. (2013). Recovery of carbon fibres by the thermolysis and gasification of waste prepreg. Journal of analytical and applied pyrolysis, 104, 675–683. Accessed Sept 2022.
Nahil, M. A., & Williams, P. T. (2011). Recycling of carbon fibre reinforced polymeric waste for the production of activated carbon fibres. Journal of Analytical and applied pyrolysis, 91(1), 67–75. Accessed Sept 2022.
Karuppannan Gopalraj, S., & Kärki, T. (2020). A Study to investigate the mechanical properties of recycled carbon fibre/glass fibre-reinforced epoxy composites using a novel thermal recycling process. Processes, 8(8), 954. Accessed Sept 2022.
Piñero-Hernanz, R., et al. (2008). Chemical recycling of carbon fibre composites using alcohols under subcritical and supercritical conditions. The Journal of Supercritical Fluids, 46(1), 83–92. Accessed Sept 2022.
Wu, T., et al. (2019). Efficient reclamation of carbon fibers from epoxy composite waste through catalytic pyrolysis in molten ZnCl 2. RSC Advances, 9(1), 377–388. Accessed Sept 2022.
Kim, Y. N., et al. (2019). Application of supercritical water for green recycling of epoxy-based carbon fiber reinforced plastic. Composites Science and Technology, 173, 66–72. Accessed Sept 2022.
Pietroluongo, M., et al. (2020). Mechanical recycling of an end-of-life automotive composite component. Sustainable Materials and Technologies, 23, e00143.
Åkesson, D., et al. (2012). Microwave pyrolysis as a method of recycling glass fibre from used blades of wind turbines. Journal of Reinforced Plastics and Composites, 31(17), 1136–1142. Accessed Sept 2022.
Cunliffe, A., Jones, N., & Williams, P. (2003). Pyrolysis of composite plastic waste. Environmental Technology, 24(5), 653–663. Accessed Sept 2022.
Ginder, R. S., & Ozcan, S. (2019). Recycling of commercial E-glass reinforced thermoset composites via two temperature step pyrolysis to improve recovered fiber tensile strength and failure strain. Recycling, 4(2), 24. Accessed Sept 2022.
Oliveux, G., Bailleul, J.-L., & Salle, E. L. G. L. (2012). Chemical recycling of glass fibre reinforced composites using subcritical water. Composites Part A: Applied Science and Manufacturing, 43(11), 1809–1818. Accessed Sept 2022.
Karuppannan Gopalraj, S., & Kärki, T. (2020). A review on the recycling of waste carbon fibre/glass fibre-reinforced composites: fibre recovery, properties and life-cycle analysis. SN Applied Sciences, 2(3), 1–21. Accessed Sept 2022.
Nakagawa, M., et al. (2014). CFRP recycling technology using depolymerization under ordinary pressure. In: Proc of the American Society for Composites (ASC) 29th Technical Conference, San Diego, CA. Accessed Sept 2022.
Howarth, J., Mareddy, S. S., & Mativenga, P. T. (2014). Energy intensity and environmental analysis of mechanical recycling of carbon fibre composite. Journal of Cleaner Production, 81, 46–50. Accessed Sept 2022.
Song, Y. S., Youn, J. R., & Gutowski, T. G. (2009). Life cycle energy analysis of fiber-reinforced composites. Composites Part A: Applied Science and Manufacturing, 40(8), 1257–1265. Accessed Sept 2022.
Thomas, C., et al. (2014). Epoxy composites containing CFRP powder wastes. Composites Part B: Engineering, 59, 260–268. Accessed Sept 2022.
Mason, H. (2021). Recycling end-of-life composite parts: New methods, markets. Available from: https://www.compositesworld.com/articles/recycling-end-of-life-composite-parts-new-methods-markets. Accessed Sept 2022.
Oliveux, G., Dandy, L. O., & Leeke, G. A. (2015). Current status of recycling of fibre reinforced polymers: review of technologies, reuse and resulting properties. Progress in Materials Science, 72, 61–99. Accessed Sept 2022.
Li, Y.-F., et al. (2021). An experimental study on mechanical behaviors of carbon fiber and microwave-assisted pyrolysis recycled carbon fiber-reinforced concrete. Sustainability, 13(12), 6829. Accessed Sept 2022.
Amaechi, C.V., et al. (2020). Economic aspects of fiber reinforced polymer composite recycling. Accessed Sept 2022.
Yuyan, L., Guohua, S., & Linghui, M. (2009). Recycling of carbon fibre reinforced composites using water in subcritical conditions. Materials Science and Engineering: A, 520(1–2), 179–183. Accessed Sept 2022.
Kim, D.-H., et al. (2019). Strain rate dependent mechanical behavior of glass fiber reinforced polypropylene composites and its effect on the performance of automotive bumper beam structure. Composites Part B: Engineering, 166, 483–496. Accessed Sept 2022.
Awais, H., et al. (2019). Effect of comingling techniques on mechanical properties of natural fibre reinforced cross-ply thermoplastic composites. Composites Part B: Engineering, 177, 107279. Accessed Sept 2022.
Vaidya, U., & Chawla, K. (2008). Processing of fibre reinforced thermoplastic composites. International Materials Reviews, 53(4), 185–218. Accessed Sept 2022.
Joshi, S. V., et al. (2004). Are natural fiber composites environmentally superior to glass fiber reinforced composites? Composites Part A: Applied Science and Manufacturing, 35(3), 371–376. Accessed Sept 2022.
Pilla, S. (2011). Handbook of bioplastics and biocomposites engineering applications. John Wiley & Sons. Accessed Sept 2022.
Akampumuza, O., et al. (2017). Review of the applications of biocomposites in the automotive industry. Polymer Composites, 38(11), 2553–2569. Accessed Sept 2022.
Khalid, M. Y., Arif, Z. U., & Al Rashid, A. (2022). Investigation of Tensile and Flexural Behavior of Green Composites along with their Impact Response at Different Energies. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(5), 1399–1410. https://doi.org/10.1007/s40684-021-00385-w. Accessed Sept 2022.
Jiang, Y., Liang, M., Wang, W., Lai, X., Xie, K., Liao, L., et al. (2022). Porous Nano-Ni/Graphene/Loofah Composites for Electromagnetic Interference Shielding. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(4), 1121–1132. https://doi.org/10.1007/s40684-021-00375-y. Accessed Sept 2022.
Mishra, A., Ferhan, A. R., Ho, C. M., Lee, J., Kim, D. H., Kim, Y. J., et al. (2021). Fabrication of Plasmon-Active Polymer-Nanoparticle Composites for Biosensing Applications. International Journal of Precision Engineering and Manufacturing-Green Technology, 8(3), 945–954. https://doi.org/10.1007/s40684-020-00257-9. Accessed Sept 2022.
Getu, D., et al. (2021). Production and characterization of bamboo and sisal fiber reinforced hybrid composite for interior automotive body application. Materials Today: Proceedings, 38, 2853–2860. Accessed Sept 2022.
Donald, A., et al. (2018). Development and characterization of aluminum matrix composites reinforced with carbonized coconut shell and silicon carbide particle for automobile piston application. Global Scientific Journals, 6(8), 390–398. Accessed Sept 2022.
Karikalan, L., et al. (2017). Hybridization of composites using natural and synthetic fibers for automotive application. International Journal of Scientific Research in Science and Technology, 7, 916–920. Accessed Sept 2022.
Suriani, M. J., et al. (2021). Delamination and manufacturing defects in natural fiber-reinforced hybrid composite: a review. Polymers, 13(8), 1323. Accessed Sept 2022.
Zulkepli, I. I., et al. (2019). Review of manufacturing process for good quality of composite assessment. IOP Conference Series: Materials Science and Engineering, 488, 012008. Accessed Sept 2022.
Rosenberg, P., et al. (2014) Investigating cavity pressure behavior in high-pressure RTM process variants. In: AIP conference proceedings. American Institute of Physics. Accessed Sept 2022.
Ricciardi, M., et al. (2014). A new cost-saving vacuum infusion process for fiber-reinforced composites: pulsed infusion. Journal of Composite Materials, 48, 1365–1373. Accessed Sept 2022.
Resin infusion processes. 2007; Available from: https://www.compositesworld.com/columns/resin-infusion-processes. Accessed Sept 2022.
Radhakrishnan, A. (2021). Towards creating multi-matrix continuous fibre polymer composites using an out-of-vacuum bag process. Accessed Sept 2022.
Van Oosterom, S., et al. (2019). An objective comparison of common vacuum assisted resin infusion processes. Composites Part A: Applied Science and Manufacturing, 125, 105528. Accessed Sept 2022.
Abdalla, F., et al. (2008). Determination of volume fraction values of filament wound glass and carbon fiber reinforced composites. ARPN Journal of Engineering and Applied Sciences, 3(4), 7–11. Accessed Sept 2022.
Sloan, J. (2008). ATL & AFP: defining the megatrends in composite aerostructures. High Performance Composites, 16(4), 68. Accessed Sept 2022.
Vaneker, T. (2017). Material extrusion of continuous fiber reinforced plastics using commingled yarn. Procedia CIRP, 66, 317–322. Accessed Sept 2022.
Fleischer, J., et al. (2018). Composite materials parts manufacturing. CIRP Annals, 67(2), 603–626. Accessed Sept 2022.
Johnson, W.,& Silva, C. J. (2018). Observations from exploration of VTOL Urban Air Mobility Designs. Accessed Sept 2022.
Kishorre Annanth, V., et al. (2022). Study on alternative composites materials for automobile windshields. Materials today: proceedings. Accessed Sept 2022.
Acknowledgements
This work was supported by a basic research program through the National Research Foundation of Korea (NRF) funded by the MSIT (NRF-2021R1A2B5B03087094 and NRF-2021R1A4A2001824). Any opinions, findings, conclusions, or recommendations expressed in this article are those of the authors alone, and do not necessarily reflect the views of NRF and MSIT. The authors thank Dabin Kim, who graduated from the department of design in Seoul National University, for providing the eVTOL aircraft model in Figure 12.
Funding
Ministry of Science and ICT, South Korea, NRF-2021R1A2B5B03087094, Sung-Hoon Ahn, NRF-2021R1A4A2001824, Sung-Hoon Ahn.
Author information
Authors and Affiliations
Contributions
JYC: Writing-Original Draft, Investigation, Formal analysis. JJ: Writing – Review & Editing, Conceptualization. Jang Hyeon Lyu: Investigation, Visualization. JP: Investigation, Visualization. GYK: Investigation, Visualization. SYC: Data Curation, Validation. YJQ: Validation. BB: Validation. BGP: Visualization, Validation. S-HA: Supervision, Project Administration, Funding acquisition.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this work.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
This paper is an invited paper (Invited Review)
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Choi, J.Y., Jeon, J.H., Lyu, J.H. et al. Current Applications and Development of Composite Manufacturing Processes for Future Mobility. Int. J. of Precis. Eng. and Manuf.-Green Tech. 10, 269–291 (2023). https://doi.org/10.1007/s40684-022-00483-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40684-022-00483-3