Abstract
In the present investigation an effort has been made to produce Al-Fly ash green composite using liquid state stir casting technique followed by green ultrasonic vibration such that it can improve wettability of fly-ash with aluminium by adding magnesium in the presence of argon gas. Addition of magnesium increases wettability of fly-ash particle in the molten aluminium and improves mechanical properties of Al-Fly ash green composite to a great extent. Incorporation of magnesium enhances the homogeneous allocation of fly ash particles in the pure aluminium alloy. More uniform distribution of Fly ash provides better mechanical properties. In this study, sample of Al/2 wt.% Mg/8 wt.% Fly ash provides most excellent outcome amongst all the selected composition. Microstructures show that the distribution of reinforcements is more uniform in this composition. TEM image shows proper wettability between aluminium and reinforcements. Density, cost estimation, hardness, toughness, ductility and tensile strength were also calculated to observe the result of magnesium and fly ash addition in aluminium matrix.
Similar content being viewed by others
References
Dwivedi, S. P., Kumar, S., & Kumar, A. (2012). Effect of turning parameters on surface roughness of A356/5% SiC composite produced by electromagnetic stir casting. Journal of Mechanical Science and Technology, 26, 3973–3979.
Sudarshan, & Surappa, M. K. (2008). Synthesis of fly ash particle reinforced A356 Al composites and their characterization. Materials Science and Engineering A, 480(2), 117–124.
Rohatgi, P. K., Weiss, D., & Gupta, N. (2006). Applications of fly ash in synthesizing low-cost MMCs for automotive and other applications. Journal of Manufacturing, 58(11), 71–76.
Rohatgi, P. K., Asthana, R., & Das, S. (1994). Low-cost fly-ash-containing aluminum-matrix composites. Journal of Manufacturing, 46, 55–59.
Dwivedi, S. P., Sharma, S., & Mishra, R. K. (2015). Microstructure and mechanical behavior of A356/SiC/fly-ash hybrid composites produced by electromagnetic stir casting. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 37, 57–67.
Casari, D., Merlin, M., & Garagnani, G. L. (2013). A comparative study on the effects of three commercial Ti–B-based grain refiners on the impact properties of A356 cast aluminium alloy. Journal of Materials Science, 48, 4365–4377.
Dwivedi, S. P., Sharma, S., & Mishra, R. K. (2016). A comparative study of waste eggshells, CaCO3, and SiC-reinforced AA2014 green metal matrix composites. Journal of Composite Materials. https://doi.org/10.1177/0021998316672295.
Zhan, W., Liu, X., & Yang, G. (2016). Film-forming mechanism and properties of Ti/Zr/Mo colored conversion coating prepared on aluminum alloy. International Journal of Precision Engineering and Manufacturing-Green Technology, 3, 297–302.
Ahn, D. G. (2016). Direct metal additive manufacturing processes and their sustainable applications for green technology: A review. International Journal of Precision Engineering and Manufacturing-Green Technology, 3, 381–395.
Lee, M. S., Seo, H. Y., & Kang, C. G. (2016). Comparative study on mechanical properties of CR340/CFRP composites through three point bending test by using theoretical and experimental methods. International Journal of Precision Engineering and Manufacturing-Green Technology, 3, 359–365.
Lee, H. (2017). Environmental impact of concentration of slurry components in thick copper CMP. International Journal of Precision Engineering and Manufacturing-Green Technology, 4, 13–18.
Lee, M. S., Seo, H. Y., & Kang, C. G. (2017). Comparative study on drawability of CR340/CFRP composites by using theoretical and experimental methods. International Journal of Precision Engineering and Manufacturing-Green Technology, 4, 97–104.
Man, J., Zhang, S., Luan, X., Hai, Y., & Cai, G. (2017). Residual stresses of α-Al2O3/Ni nano-composite coating prepared by automatic brush plating technique. International Journal of Precision Engineering and Manufacturing-Green Technology, 4, 19–25.
Hashim, J., Looney, L., & Hashmi, M. (2001). The enhancement of wettability of SiC particles in cast aluminium matrix composites. Journal of Materials Processing and Technology, 119, 329–335.
Naidich, Y., Zhuravlev, V., & Krasovskaya, N. (1998). The wettability of silicon carbide by Au–Si alloys. Materials Science and Engineering A, 245, 293–299.
Hashim, J., Looney, L., & Hashmi, M. (2001). The wettability of SiC particles by molten aluminium alloy. Journal of Materials Processing and Technology, 119, 324–328.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Sharma, P.K., Dwivedi, S.P., Kumar, A. et al. Effect of Magnesium Addition on Mechanical Properties of Al-Fly Ash Green Composite Produced Under Green Ultrasonic Vibration Process. Int. J. of Precis. Eng. and Manuf.-Green Tech. 6, 559–566 (2019). https://doi.org/10.1007/s40684-019-00044-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40684-019-00044-1