Abstract
This study is an optimized extension based on the authors’ previous research on the tribo-chemical reaction under constant temperature field of two-stroke internal combustion engines (ICEs). It establishes a coupled analysis model that considers the tribo-chemical reactions, dynamic contact, and interface lubrication of the piston ring-cylinder liner (PRCL) system under transient temperature conditions. In this study, for the first time, the prediction of the tribofilm thickness and its influence on the surface micro-topography (the comprehensive roughness) are coupled in the working temperature field of the PRCL system, forming an effective model framework and providing a model basis and analytical basis for subsequent research. This study findings reveal that by incorporating temperature and tribofilm into the simulation model, the average friction deviation throughout the stroke decreases from 8.92% to 0.93% when compared to experimental results. Moreover, the deviation during the combustion regime reduces from 39.56% to 7.34%. The proposed coupled model provides a valuable tool for the evaluation of lubrication performance of the PRCL system and supports the analysis software forward design in two-stroke ICEs.
![](http://media.springernature.com/lw685/springer-static/image/art%3A10.1007%2Fs40544-024-0872-9/MediaObjects/40544_2024_872_Fig1_HTML.jpg)
Article PDF
Avoid common mistakes on your manuscript.
References
Wang Z G, Zhou S, Feng Y M, Zhu Y Q. Research of NOx reduction on a low-speed two-stroke marine diesel engine by using EGR (exhaust gas recirculation)-CB (cylinder bypass) and EGB (exhaust gas bypass). Int J Hydrog Energy 42(30): 19337–19345 (2017)
Ryk G, Kligerman Y, Etsion I, Shinkarenko A. Experimental investigation of partial laser surface texturing for piston-ring friction reduction. Tribol Trans 48(4): 583–588 (2005)
Richardson D E. Review of power cylinder friction for diesel engines. J Eng Gas Turbines Power 122(4): 506–519 (2000)
Lyu X Y, Azam A, Wang Y C, Lu X Q, Li T Y, Zou D Q, Ma X, Wilson M C, Neville A. An efficient procedure to predict the dynamic loads for piston liner systems in marine engines. Int J Engine Res 23(4): 678–692 (2022)
Miao C W, Guo Z W, Yuan C Q. Tribological behavior of co-textured cylinder liner-piston ring during running-in. Friction 10(6): 878–890 (2022)
Liu X R, Li G X, Bai S Z, Hu Y P. Mixed lubrication and friction power loss of piston ring pack. Appl Mech Mater 668–669: 205–208 (2014)
Jiao B W, Li T Y, Ma X, Wang C J, Xu H Z, Lu X Q, Liu Z G. Lubrication analysis of the piston ring of a two-stroke marine diesel engine considering thermal effects. Eng Fail Anal 129: 105659 (2021)
Muše A, Jurić Z, Račić N, Radica G. Modelling, performance improvement and emission reduction of large two-stroke diesel engine using multi-zone combustion model. J Therm Anal Calorim 141(1): 337–350 (2020)
Spikes H. The history and mechanisms of ZDDP. Tribol Lett 17(3): 469–489 (2004)
Barnes A M, Bartle K D, Thibon V R A. A review of zinc dialkyldithiophosphates (ZDDPS): Characterisation and role in the lubricating oil. Tribol Int 34(6): 389–395 (2001)
Ferrari E S, Roberts K J, Adams D. A multi-edge X-ray absorption spectroscopy study of the reactivity of zinc di-alkyl-di-thiophosphates (ZDDPS) anti-wear additives: Wear 236(1–2): 246–258 (1999)
Vengudusamy B, Green J H, Lamb G D, Spikes H A. Tribological properties of tribofilms formed from ZDDP in DLC/DLC and DLC/steel contacts. Tribol Int 44(2): 165–174 (2011)
Čoga L, Akbari S, Kovač J, Kalin M. Differences in nanotopography and tribochemistry of ZDDP tribofilms from variations in contact configuration with steel and DLC surfaces. Friction 10(2): 296–315 (2022)
Zhang J, Spikes H. On the mechanism of ZDDP antiwear film formation. Tribol Lett 63(2): 24 (2016)
Fujita H, Spikes H A. Study of zinc dialkyldithiophosphate antiwear film formation and removal processes, part II: Kinetic model. Tribol Trans 48(4): 567–575 (2005)
Lyu X Y, Jiao B W, Wang Y C, Azam A, Lu X Q, Zou D Q, Ma X, Neville A. An improved contact model considered the effect of boundary lubrication regime on piston ring-liner contact for the two-stroke marine engines from the perspective of the Stribeck curve. Proc Inst Mech Eng Part C J Mech Eng Sci 236(5): 2602–2616 (2022)
Taylor R I. Tribology and energy efficiency: From molecules to lubricated contacts to complete machines. Faraday Discuss 156: 361 (2012)
Smith G C. Surface analytical science and automotive lubrication. J Phys D: Appl Phys 33(20): R187–R197 (2000)
Spikes H. Low- and zero-sulphated ash, phosphorus and sulphur anti-wear additives for engine oils. Lubr Sci 20(2): 103–136 (2008)
Ye Z K, Zhang C, Wang Y C, Cheng H S, Tung S, Wang Q J, He X Z. An experimental investigation of piston skirt scuffing: A piston scuffing apparatus, experiments, and scuffing mechanism analyses. Wear 257(1–2): 8–31 (2004)
Gara L, Zou Q, Sangeorzan B P, Barber G C, McCormick H E, Mekari M H. Wear measurement of the cylinder liner of a single cylinder diesel engine using a replication method. Wear 268(3–4): 558–564 (2010)
Gosvami N N, Bares J A, Mangolini F, Konicek A R, Yablon D G, Carpick R W. Mechanisms of antiwear tribofilm growth revealed in situ by single-asperity sliding contacts. Science 348(6230): 102–106 (2015)
Pu W, Zhang Q, Zhang W, Ren S, Chen Z, Tian T. Flash temperature and anti-wear tribofilm growth mechanisms by asperity contact in top-ring/liner conjunction of IC engines. Tribol Int 146: 106186 (2020)
Leighton M, Morris N, Rahnejat H. Transient nanoscale tribofilm growth: Analytical prediction and measurement. Appl Sci 11(13): 5890 (2021)
Fox-Rabinovich G S, Gershman I S, Endrino J L. Accelerated tribo-films formation in complex adaptive surface-engineered systems under the extreme tribological conditions of ultra-high-performance machining. Lubricants 11(5): 221 (2023)
Lu X Q, Li Q, Zhang W P, Guo Y B, He T, Zou D Q. Thermal analysis on piston of marine diesel engine. Appl Therm Eng 50(1): 168–176 (2013)
Li W Y, Guo Y B, He T, Lu X Q, Zou D Q. Interring Gas Dynamic Analysis of Piston in a Diesel Engine considering the Thermal Effect. Math Probl Eng 2015: 176893 (2015)
Greenwood J A, Tripp J H. The contact of two nominally flat rough surfaces. Proc Inst Mech Eng 185(1): 625–633 (1970)
Bewsher S R, Leighton M, Mohammadpour M, Rahnejat H, Offner G, Knaus O. Boundary friction characterisation of a used cylinder liner subject to fired engine conditions and surface deposition. Tribol Int 131: 424–437 (2019)
Li Y, Chen H J, Tian T. A deterministic model for lubricant transport within complex geometry under sliding contact and its application in the interaction between the oil control ring and rough liner in internal combustion engines. SAE Technical Paper 2008-01-1615 (2008)
Guo YB, Lu X Q, Li W Y, He T, Zou D Q. A mixed-lubrication model considering elastoplastic contact for a piston ring and application to a ring pack. Proc Inst Mech Eng Part D J Automob Eng 229(2): 174–188 (2015)
Patir N, Cheng H S. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication. J Lubr Technol 100(1): 12–17 (1978)
Patir N, Cheng H S. Application of average flow model to lubrication between rough sliding surfaces. J Lubr Technol 101(2): 220–229 (1979)
Wu C W, Zheng L Q. An average Reynolds equation for partial film lubrication with a contact factor. J Tribol 111(1): 188–191 (1989)
Tomanik E, Chacon H, Teixeira G. A simple numerical procedure to calculate the input data of Greenwood- Williamson model of asperity contact for actual engineering surfaces. Tribol Ser 41: 205–215 (2003)
Wen S, Huang P. Principles of tribology. J Tribol 99(2): 305–306 (1977).
Leighton M, Rahmani R, Rahnejat H. Surface-specific flow factors for prediction of friction of cross-hatched surfaces. Surf Topogr: Metrol Prop 4(2): 025002 (2016)
Grützmacher P G, Profito F J, Rosenkranz A. Multi-scale surface texturing in tribology—Current knowledge and future perspectives. Lubricants 7(11): 95 (2019)
Mosey N J, Müser M H, Woo T K. Molecular mechanisms for the functionality of lubricant additives. Science 307(5715): 1612–1615 (2005)
Akchurin A, Bosman R. A deterministic stress-activated model for tribo-film growth and wear simulation. Tribol Lett 65(2): 59 (2017)
Ghanbarzadeh A, Piras E, Wilson M C T, Morina A, Neville A. Numerical study of the effect of tribofilm kinetics and its hardness on the roughness evolution of the substrate in boundary lubrication regime. Tribol Trans 62(5): 747–759 (2019)
Ghanbarzadeh A, Piras E, Nedelcu I, Brizmer V, Wilson M C T, Morina A, Dowson D, Neville A. Zinc dialkyl dithiophosphate antiwear tribofilm and its effect on the topography evolution of surfaces: A numerical and experimental study. Wear 362–363: 186–198 (2016)
Hu Y Z, Li N, Tónder K. A dynamic system model for lubricated sliding wear and running-In. J Tribol 113(3): 499–505 (1991)
Yu X, Fei Z, Yan Z. The research of the boundary conditions of steady thermal conduction on the inner surface of cylinder in internal combustion engines. Trans Csice 5: 324–332 (1987) (In Chinese)
Roshan R, Priest M, Neville A, Morina A, Xia X, Warrens C P, Payne M J. Friction modelling in boundary lubrication considering the effect of MoDTC and ZDDP in engine oils. Tribol Online 6(7): 301–310 (2011)
Wang Y, Ma X, Li T, Lu X, Li W. Influence of thermal effect in piston skirt lubrication considering thermal deformation of piston and cylinder liner. Int J Engine Res 24(8): 678–692 (2023)
Fang C C, Meng X H, Xie Y B, Wen C W, Liu R C. An improved technique for measuring piston-assembly friction and comparative analysis with numerical simulations: Under motored condition. Mech Syst Signal Process 115: 657–676 (2019)
Li R, Wen C W, Meng X H, Xie Y B. Measurement of the friction force of sliding friction pairs in low-speed marine diesel engines and comparison with numerical simulation. Appl Ocean Res 121: 103089 (2022)
Acknowledgements
This work was supported by the Shandong Provincial Natural Science Foundation (No. ZR2022QE183). We also thank Dr. Abdullah Azam and Prof. Anne Neville for their support and the active discussions and valuable comments during this work (Dr. Abdullah Azam: The University of Leeds, A.Azam@leeds.ac.uk; Prof. Anne Neville: A.Neville@leeds.ac.uk).
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
The authors have no competing interests to declare that are relevant to the content of this article.
Additional information
Xiuyi LYU. He received his Ph.D. degree from Harbin Engineering University in 2022. During this period, he went to the University of Leeds for a one-year exchange as a joint Ph.D. student, under the guidance of Professor Anne Neville. He joined the School of Shipping and Naval Architecture at Chongqing Jiaotong University. His research areas cover friction pair with low-friction design for IC engines, tribo-chemical reaction, and tribofilm.
Jiang HU. He received his bachelor degree in mechanical engineering in 2017 from Chongqing Technology and Business University, Chongqing, China. Now, he is pursuing his master degree at Chongqing Jiaotong University. His research interests include friction-reducing design and mixed lubrication.
Xuan MA. He received his Ph.D. degree from Harbin Engineering University in 2018. He joined the College of Power and Energy Engineering in HEU. He is an associate professor in the College. His research areas cover the development of new anti-wear technology for ship power systems.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Lyu, X., Hu, J., Wang, Y. et al. Effect of temperature on tribofilm growth and the lubrication of the piston ring-cylinder liner system in two-stroke marine engines. Friction 12, 1858–1881 (2024). https://doi.org/10.1007/s40544-024-0872-9
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40544-024-0872-9