Friction

, Volume 5, Issue 1, pp 66–86 | Cite as

Optimization of friction and wear characteristics of varied cryogenically treated hot die steel grade AISI-H13 under dry condition

Open Access
Research Article

Abstract

Cryogenic treatment (CT) is a relatively new field, which has emerged during the last three decades of the twentieth century. However, its impact on material shaping and making tool life, and enhancement of their mechanical properties are quite remarkable. The selection of appropriate process parameters for CT is essential for cost reduction and optimum productivity. This study focuses on the influence of key parameters of CT cycles (i.e., soaking temperature and duration) on the friction and wear behavior of AISI H13 hot die steel under dry sliding conditions against hardened and tempered AISI D3 cold work tool steel (counter face) at varying sliding speeds and loads. Mathematical models have been developed for wear rate, the average coefficient of friction, and maximum contact temperature using the Box-Cox methodology. The developed mathematical models have been validated by comparing with the experimental results. Moreover, the optimum values of the process parameter have been employed to maximize the output and validate the same by confirmation of the experiments. To the best of our knowledge, this is the first study that demonstrates the modeling and optimization of sliding friction and wear characteristics of AISI H13 under varied CT cycles.

Keywords

cryogenics treatment hot die steel friction wear modeling Box-Cox method optimization 

Notes

Acknowledgments

The authors gratefully acknowledge their gratitude to the National Institute of Technology, Hamirpur to grant funds for the procurement of the hot die steel material, making available their tribological test; Institute of Auto Parts and Hand tools Technology, Ludhiana for extending facilities under the expert supervision of spectroscopic analysis, vacuum heat treatment and cryogenic treatment facility required for the study.

References

  1. [1]
    Roberts G. Tools Steels. 5th Ed. Materials Park, OH, USA: ASM International, 1998: 46–66.Google Scholar
  2. [2]
    Lal D M, Renganarayanan S, Kalanidhi A. Cryogenic treatment to augment wear resistance of tool and die Steel. Cryogenics 41: 149–55 (2001)CrossRefGoogle Scholar
  3. [3]
    Barron R F. Effects of cryogenic treatment on lath tool wear. Progress in Refrigeration Science and Technology, Publishing Co. Westport 1: 529–34 (1973)Google Scholar
  4. [4]
    Das D, Dutta A K, Ray K K. Sub-Zero treatments of AISI D2 Steel: Part I. Microstructure and hardness. Mater Sci Eng A 527: 2182–2193 (2010)CrossRefGoogle Scholar
  5. [5]
    Mehtedi M E, Ricci P, Drudi L, Mohtadi S E, Cabibbo M, Spigarelli S. Analysis of the effect of deep cryogenic treatment on the hardness and microstructure of X30CrMoN 15 1 steel. Mater Design 33: 136–144 (2012)CrossRefGoogle Scholar
  6. [6]
    Koneshlou M, Meshinchi K, Khomamizadeh F. Effect of cryogenic treatment on microstructure, mechanical and wear behaviors of AISI H13 hot work tool steel. Cryogenics 51: 55–61 (2011)CrossRefGoogle Scholar
  7. [7]
    Katoch S, Sehgal R, Singh V. Effect of cryogenic treatment on hardness, microstructure and wear behavior of hot die steel grade AISI-H13. In Proceeding of International Conference on Advances in Tribology and Engineering Systems, 2014: 159–166.CrossRefGoogle Scholar
  8. [8]
    Amini K, Nategh S, Shafyei A. Influence of different cryotreatments on tribological behavior of 80CrMo12 5 cold work tool steel. Mater Design 31: 4666–4675 (2010)CrossRefGoogle Scholar
  9. [9]
    Das D, Dutta A K, Ray K K. Influence of varied cryo-treatment on the wear behavior of AISI D2 steel. Wear 266: 297–309 (2009)CrossRefGoogle Scholar
  10. [10]
    Gunes I, Cicek A, Aslantas K, Kara F. Effect of deep cryogenic treatment on wear resistance of AISI 52100 bearing steel. Trans Indian Inst Met 67: 909–917 (2014)CrossRefGoogle Scholar
  11. [11]
    Yong A Y L, Seah K H W, Rehman M. Performance of cryogenically treated tungsten carbide tools in milling operations. Int J Adv Manuf Technol 32: 638–643 (2007)CrossRefGoogle Scholar
  12. [12]
    Firouzdor V, Nejati E, Khomamizadeh F. Effect of deep cryogenic treatment on wear resistance and tool life of M2 HSS drill. J Mater Process Technol 206: 467–472 (2008)CrossRefGoogle Scholar
  13. [13]
    Huang Y, Zhu Y T, Liao X Z, Beyerlein I J, Bourlce M A, Mitchell T E, Microstructure of cryogenic treated M2 Tool Steel. Mater Sci Eng A 339: 241–244 (2003)Google Scholar
  14. [14]
    ASTM E 415-2014. Standard test method for Analysis of carbon and low alloy steel by spark atomic emission spectrometry. ASTM Annual Book of Standards. West Conshohocken, PA, United States.Google Scholar
  15. [15]
    Bayer A M, Vasco T, Walton L R. Properties and selection: Iron, steels and high performance alloys. ASM Handbook, 3rd ed. ASM International, Materials Park, OH, USA, 1995.Google Scholar
  16. [16]
    ASTM E10-2010. Standard test method for Brinell hardness of metallic materials. ASTM Annual Book of Standards. West Conshohocken, PA, United States, 2010: 91–122.Google Scholar
  17. [17]
    ASTM G77-2010. Standard test method for ranking resistance of materials to sliding wear using block-on-ring wear test. ASTM Annual Book of Standards. West Conshohocken, PA, United States.Google Scholar
  18. [18]
    ASTM E384-08a (2009). Standard test method for micro indentation hardness of materials. ASTM Annual Book of Standard, Vol. 3.01. West Conshohocken, PA, United States.Google Scholar
  19. [19]
    George F Vander Voort. Metallography and microstructure. ASM Handbook, 9th ed. ASM International, Materials Park, OH, USA, 1995: 257-263.Google Scholar
  20. [20]
    Suh N P. An overview of the delamination theory of wear. Wear 44:1–16 (1977)CrossRefGoogle Scholar
  21. [21]
    Sharma M D, Sehgal R, Pant M. Tribological behavior of Ti3Al2.5V alloy against EN-31 steel under dry condition. Tribol Trans 59(3): 451–461 (2016)CrossRefGoogle Scholar

Copyright information

© The Author(s) 2016

Open Access: The articles published in this journal are distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Authors and Affiliations

  1. 1.Centre for Materials Science and EngineeringNational Institute of TechnologyHamirpur (HP)India
  2. 2.Institute for Auto Parts & Hand Tools Technology, A-9, Phase VFocal PointLudhiana (Punjab)India
  3. 3.Department of Mechanical EngineeringNational Institute of TechnologyHamirpur (HP)India

Personalised recommendations