Advertisement

Friction

, Volume 4, Issue 1, pp 1–28 | Cite as

Overview of automotive engine friction and reduction trends–Effects of surface, material, and lubricant-additive technologies

  • Victor W. WongEmail author
  • Simon C. TungEmail author
Open Access
Review Article

Abstract

The increasing global environmental awareness, evidenced by recent worldwide calls for control of climate change and greenhouse emissions, has placed significant new technical mandates for automotives to improve engine efficiency, which is directly related to the production of carbon dioxide, a major greenhouse gas. Reduction of parasitic losses of the vehicle, powertrain and the engine systems is a key component of energy conservation. For engine efficiency improvement, various approaches include improvements in advanced combustion systems, component system design and handling—such as down-sizing, boosting, and electrification—as well as waste heat recovery systems etc. Among these approaches, engine friction reduction is a key and relatively cost-effective approach, which has been receiving significant attention from tribologists and lubricant-lubrication engineers alike. In this paper, the fundamentals of friction specific to the environments of engine components tribology are reviewed, together with discussions on the impact of developing vehicle powertrain technologies, surface and material technologies, as well as lubricant and additive technologies on promises of continuing friction and wear reduction trends. The international accords on climate change require further gains in fuel efficiency and energy sustainability from all industry sectors including those in the automotive and the broader internal combustion engine industries, and the latter encompass off-highway, power generation, marine, and rail industries as well. This paper focsuses on friction reduction in mainly automotive engines, however.

The paper starts with a clarification of the common descriptors of mechanical losses and friction in the engine, followed by the topic of lubrication fundamentals such as lubrication regimes. Then the lubrication of the contacting surfaces in each of the major engine subsystems is discussed in turn. These subsystems include the piston assembly: ring-pack/liner, piston-skirt/liner, and piston-pin/connecting-rod contacts; connecting rod and crankshaft bearings; and the valvetrain subsystem. The relative contributions to total friction from the various subsystems are discussed, with the piston-assembly contributing to about half of the total friction. The remainder of the friction comes from the crankshaft, connecting rod, camshaft bearings, and the valvetrain oscillating parts. The bearings are in predominantly hydrodynamic lubrication, in contrast to the valvetrain oscillating components, which are characterized to be mostly in the mixed/boundary lubrication regimes.

Despite the title of the paper, a section on emerging powertrain technologies—including that of combustion in gasoline and diesel engines—is also given in the context of the trend towards clean and efficient propulsion systems. The impact of these developing technologies on the reduction of friction and parasitic losses via component, material, and lubricant deisgn will be discussed. These technologies include gasoline direct injection (GDI), turbocharged, and hybrid vehicles and will generate unique green environmental opportunities for future propulsion systems. These technologies are critical to meet fuel economy and reduced emission targets. Specifically, this paper will address the impact of these emerging technologies on future lubricant requirements and advanced tribology research. The connection between these lubricant and tribological requirements will be illustrated by briefly describing the basic lubrication and friction processes at the major engine components incorporating the emerging technologies.

Lastly, besides new hardware and material science changes, several advanced additives such as advanced friction modifiers, antiwear additive chemistries, low viscosity lubricants, and the introduction of new VI Improvers all represent possible tribological solutions to the challenge of meeting more stringent energy efficiency requirements and environmental legislation. As original equipment manufacturers (OEMs) seek to accomplish these goals, hardware and emission system changes will place new demands and even greater stress on engine oils. At the same time, engine durability, performance and reliability are of primary importance to vehicle owners and operators. The final section of this paper will discuss the future trends of engine friction reduction and wear control by surface modification such as friction-reducing coatings or surface textures in engine components. The impact of surface coatings or surface textures on engine friction will be reviewed. In addition, the OEMs and lubricant formulation manufacturers will need to respond with novel engine oil technologies formulated to protect the engine, keeping the emissions system working at the optimal fuel economy, while retaining engine durability.

In brief, the paper (i) reviews the characteristics of component friction in the environment of the internal combustion engine and the relevant design considerations, (ii) addresses the impact of emerging technologies on engine friction and the tribological changes and requirements, especially on lubricant and additives, and lastly (iii) discusses the interactions between lubricant-additive formulations and material surface engineering, and their effects on friction, wear and engine durability. The increasing importance and interplay between synergistic advancements in component design, material and surface engineering, and advanced lubricant-additive formulation will be fully illustrated.

Keywords

powertrain tribology automotive lubricants additive formulation mechanical design surface coatings and textures friction wear 

References

  1. [1]
    Holmberg K, Andersson P, Erdemir A. Global energy consumption due to friction in passenger cars. Tribol Int 47: 221–234 (2012)CrossRefGoogle Scholar
  2. [2]
    Holmberg K., Andersson P, Nylund O, Mäkelä K. Global energy consumption due to friction in trucks and buses. Tribol Int 78: 94–114 (2014)CrossRefGoogle Scholar
  3. [3]
    Allmaier H, Knauder C, Salhofer S, Reich F, Schalk E, Ofner H, Wagner A. An Experimental study of the load and heat influence from combustion on engine friction. Int J Eng Res 17(3): 347–353 (2016)CrossRefGoogle Scholar
  4. [4]
    Sandoval D, Heywood J. An improved friction model for spark-ignition engines. SAE Paper # 2003-01-0725, Society of Automotive Engineers, Warrendale, PA, 2003.CrossRefGoogle Scholar
  5. [5]
    Taraza D, Henein N A, Ceausu R, Bryzik W. Engine friction model for transient operation of turbocharged, common rail diesel engines. SAE Paper # 2007-01-1460, SAE, Warrendale, PA, 2007.CrossRefGoogle Scholar
  6. [6]
    Patton K J, Nitschke R G, Heywood J B. Development and evaluation of a friction model for spark-ignition engines. SAE Paper # 890836, Society of Automotive Engineers, Warrendale, PA, 1989.CrossRefGoogle Scholar
  7. [7]
    Richardson D. Review of power cylinder friction for diesel engines. J Eng Gas Turbine Power, Trans the ASME 122(4): 506–519 (2000)CrossRefGoogle Scholar
  8. [8]
    Quillen K, Stanglmaier R H, Moughon L, Takata R, Wong V, Reinbold E, Donohue R. Friction reduction by piston ring pack modifications of a lean-burn 4-stroke natural gas engine: Experimental results. In Proceedings of ASME ICED Spring Technical Conference, Aachen, Germany, 2006, ASME Paper ICES2006-1327.Google Scholar
  9. [9]
    Quillen K, Stanglmaier R H, Wong V, Reinbold E, Donahue R, Tellier K, Carey V. Friction reduction due to lubrication oil changes in a lean-burn 4-stroke natural gas engine: Experimental results. In Joint Rail Conference & Internal Combustion Engine Division Spring Technical Conference, Pueblo, Colorado, 2007, ASME Paper JRCICE 2007-40128.Google Scholar
  10. [10]
    Nakada M. Piston and piston ring tribology and fuel economy. In Proceedings of the International Tribology Conference, Yokohama, 1995Google Scholar
  11. [11]
    Taylor C M. Engine Tribology. Amsterdam: Elsevier Science Publishers, 1993Google Scholar
  12. [12]
    Heywood, J. Internal Combustion Engine Fundamentals. McGraw-Hill, New York, NY, 1988.Google Scholar
  13. [13]
    James C J. Analysis of parasitic losses in heavy duty diesel engines. M.S. Thesis. Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA, 2012.Google Scholar
  14. [14]
    Mansouri S H, Wong V W. Effects of piston design parameters on piston secondary motion and skirt-liner friction. SAE Paper # 2004-01-2911, Society of Automotive Engineers, Warrendale, PA, 2004.CrossRefGoogle Scholar
  15. [15]
    Moughon L. Effects of piston design and lubricant selection on reciprocating engine friction. M.S. Thesis. Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA, 2006.Google Scholar
  16. [16]
    Patir N, Cheng H S. Application of average flow model to lubrication between rough sliding surfaces. ASME J Lubr Tech 101: 220–230 (1979)CrossRefGoogle Scholar
  17. [17]
    Greenwood J A, Tripp J. The Contact of two nominally flat surfaces. Proc Inst Mech Engrs 185: 625–633 (1971)CrossRefGoogle Scholar
  18. [18]
    Smedley G. Piston ring design for reduced friction in modern internal combustion engines. M.S. Thesis. Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA, 2004.Google Scholar
  19. [19]
    Allmaier H, Priestner C, Franz Markus R, Novotny-Farkus F. Predicting friction reliably and accurately in journal bearings—A systematic validation of simulation results with experimental measurements. Tribol Int 58: 20–28 (2013)CrossRefGoogle Scholar
  20. [20]
    Sander D E, Allmaier H, Priebsch H H, Reich F M, Witt M, Füllenbach T, Skiadas A, Brouwer L, Schwarze H. Impact of high pressure and shear thinning on journal bearing friction. Tribol Int 81: 29–37 (2015)CrossRefGoogle Scholar
  21. [21]
    Wachtmeister G, Hubert A. Rotation of a piston pin in the small connecting rod eye during engine operation. MTZ Worldwide 69(12): 52–57 (2008)CrossRefGoogle Scholar
  22. [22]
    Nishikawa C. Optimization of semi-floating piston pin boss formed by using oil-film simulations. SAE Paper # 2012-01-0908, Society of Automotive Engineers, Warrendale, PA, 2012.CrossRefGoogle Scholar
  23. [23]
    Wang X, Du J, Zhang J. (2011) Mixed lubrication analysis of piston pin bearing in diesel engine with high power density. In ASME/STLE 2011 International Joint Tribology Conference, Los Angeles, CA, 2011, ASME Paper # IJTC 2011-61185.CrossRefGoogle Scholar
  24. [24]
    Ligier J, Ragot P. Piston pin: Wear and rotating motion. SAE Paper # 2005-01-1651, Society of Automotive Engineers, Warrendale, PA, 2005.Google Scholar
  25. [25]
    Takiguchi M, Suhara T, Tsuneo S. Reduction of friction for piston pin boss bearing of automotive gasoline engine by utilizing oil around the boss. American Society of Mechanical Engineers, New York, NY, 1998, ASME Paper # 98-ICE-101.Google Scholar
  26. [26]
    Bishop I N. Effect of design variables on friction and economy. SAE Trans 73: 334–358 (1965)Google Scholar
  27. [27]
    Lee S, Shannon B A, Mikulec A, Vrsek G. Applications of friction algorithms for rapid engine concept assessments. SAE Paper # 1999-01-0558, Society of Automotive Engineers, Warrendale, PA, 1999.CrossRefGoogle Scholar
  28. [28]
    Wang Y. Introduction to engine valvetrains. Special Publication, by Society of Automotive Engineers, Warrendale, PA, 2007.Google Scholar
  29. [29]
    Staron J T, Willermet P A. An analysis of valve train friction in terms of lubrication principles. SAE Paper # 830165, Soc. of Automotive Engineers, Warrendale, PA, 1983.CrossRefGoogle Scholar
  30. [30]
    Comfort A. An introduction to heavy-duty diesel engine frictional losses and lubricant properties affecting fuel economy–Part I. SAE Paper # 2003-01-3225, Society of Automotive Engineers, Warrendale, PA, 2003.CrossRefGoogle Scholar
  31. [31]
    Beloiu D M. Modeling and analysis of valve train, Part I–Conventional systems. SAE Int J Eng 3(1): 850–877 (2010)CrossRefGoogle Scholar
  32. [32]
    Gangopadhyay A, Soltis E, Johnson M D. Valvetrain friction and wear: Influence of surface engineering and lubricants. Proc Inst Mech Eng Part J: J Eng Tribol 218: 147–156 (2004)CrossRefGoogle Scholar
  33. [33]
    de Paula Pignatti T, Miziara W, Esteves da Cunha R. Reduced friction for a four cylinder two valve otto engine valve train. SAE Paper # 2011-36-0208E, Society of Automotive Engineers, Warrendale, PA, 2011.CrossRefGoogle Scholar
  34. [34]
    Takata R, Li Y, Wong V. Effect of liner surface texturing on ring/liner friction in large-bore engines. In Proceedings of ICEF06, ASME Internal Combustion Engine Div. 2006 Fall Technical Conf., Sacramento, Calif., USA, 2006, Paper ICEF2006-1525.CrossRefGoogle Scholar
  35. [35]
    Hamilton D B, Walowit J A, Allen C M. A theory of lubrication by microasperities. ASME J Basic Eng 88: 177–185 (1966)CrossRefGoogle Scholar
  36. [36]
    Anno J N, Walowit J A, Allen C M. Microasperity lubrication. ASME J Lubr Tech 90: 351–355 (1968)CrossRefGoogle Scholar
  37. [37]
    Anno J N, Walowit J A, Allen C M. Load support and leakage from microasperity-lubricated face seals. ASME J Lubr Tech 91: 726–731 (1969)CrossRefGoogle Scholar
  38. [38]
    Kovalchenko A, Ajayi O, Erdemir A, Fenske G, Etsion I. The effect of laser surface texturing on transitions in lubrication regimes during unidirectional sliding contact. Tribol Int 38: 219–225 (2005)CrossRefGoogle Scholar
  39. [39]
    Sadeghi F, Wang C P. Advanced natural gas reciprocating engine: parasitic loss control through surface modification. ARES/ARICE Low Engine Friction Alliance Workshop, Cambridge, MA, 2005.Google Scholar
  40. [40]
    Ronen A, Etsion I, Kligerman Y. Friction-reducing surfacetexturing in reciprocating automotive components. Tribol Trans 44: 359–366 (2001)CrossRefGoogle Scholar
  41. [41]
    Ryk G, Kligerman Y, Etsion I. Experimental investigation of laser surface texturing for reciprocating automotive components. Tribol Trans 45: 444–449 (2002)CrossRefGoogle Scholar
  42. [42]
    Siripuram R, Stephens L. Effect of deterministic asperity geometry on hydrodynamic lubrication. ASME J Tribol 126: 527–534 (2004)CrossRefGoogle Scholar
  43. [43]
    Hsu S. Integrated surface modification technology development. Presented at Oak Ridge National Laboratory on 9/15/2005, http://web.ornl.gov/sci/propulsionmaterials/pdfs/2005_Presentations/PM_9407%20Presentation_Hsu.pdf.Google Scholar
  44. [44]
    Michail S K, Barber G C. The effects of roughness on piston ring lubrication Part I: Model development. Tribol Trans 38: 19–26 (1995)CrossRefGoogle Scholar
  45. [45]
    Jocsak J, Li Y, Tian T, Wong V W. Analyzing the effects of three-dimensional cylinder liner surface texture. In ICEF 2005, Ottawa, Canada, 2005, #ICE 2005-1333.Google Scholar
  46. [46]
    Moore J. Future automotive powertrain outlook. SAE Fuels and Lubricants Committee Report, 2013.Google Scholar
  47. [47]
    Howard K. Turbocharged direct injection is engine oil’s next big hurdle. LUBES’N’GREASES Magazine, 2013.Google Scholar
  48. [48]
    Tung S C. Impact of modern engine innovation to the future tribology requirements. Keynote presentation at German Tribology Conference, Organized by German Tribology Society, Gottingen, Germany, 2014.Google Scholar
  49. [49]
    Haycock R F, Caines A J, Hiller J. Automotive Lubricants Reference Book, Third Edition. Society of Automotive Engineers, Warrendale, PA, 2008.Google Scholar
  50. [50]
    Sappok A, Munnis S, Wong V W. Individual and synergistic effects of lubricant additive components on diesel particulate filter ash accumulation and performance. In ASME 2012 Internal Combustion Engine Division Spring Technical Conference, Turin, Italy, 2012, ASME Paper # ICES 2012-81237.CrossRefGoogle Scholar
  51. [51]
    McGeehan J A, Moritz J, Shank G, Kennedy S, Stehouwer D, Urbank M, Belay M, Goodier S, Cassim A, Runkle B, et al. API CJ-4: Diesel oil category for both legacy engines and low emission engines using diesel particulate filter. SAE Paper # 2006-01-3439, Society of Automotive Engineers, Warrendale, PA, 2006.Google Scholar
  52. [52]
    Bodek K M, Wong V W. The effects of sulfated ash phosphorus and sulfur on diesel aftertreatment systems—A review. SAE Paper # 2007-01-1922. JSAE # 20077200, Society of Automotive Engineers, Warrendale, PA., 2007.CrossRefGoogle Scholar
  53. [53]
    Sappok A, Munnis S, Wong V. Individual and synergistic effects of lubricant additive components on diesel particulate filter ash accumulation and performance. In ASME 2012 Internal Combustion Engine Division Spring Technical Conference, Turin, Italy, 2012, ASME Paper# ICES 2012-81237.CrossRefGoogle Scholar
  54. [54]
    Wasserscheid P, Keim A W. Introduction of ionic liquids. Chem Int Ed Engl 39: 3772 (2000)Google Scholar
  55. [55]
    Syed Q A, Rizwi A. Comprehensive Review of Lubricant Chemistry, Technology Selection, and Design. ASTM Handbook, ASTM, 2009.Google Scholar
  56. [56]
    Mathias W. Non-petroleum-based, no/low SAP and bionotox engine oil development and testing. Tung S, Totten G Ed. In ASTM Automotive Lubricant and Testing Handbook, 2013.Google Scholar
  57. [57]
    Molewyk M A. In-situ control of lubricant properties for reduction of power cylinder friction through thermal barrier costing. M. S. Thesis. Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA, 2014.Google Scholar
  58. [58]
    Haycock R F, Caines A J, Hiller J. Automotive Lubricants Reference Book, Second Edition. Society of Automotive Engineers, Warrendale, PA, 2004.Google Scholar
  59. [59]
    Tung S, Totten G Ed. ASTM Automotive Lubricant and Testing Handbook Chapter 2 and Chapter 6. ASTM/SAE MNL, 2013.Google Scholar
  60. [60]
    Mortier R M, Fox M F, Orszalik S T. Chemistry and Technology of Lubricants, Third Edition. Springer, Dordrecht, Netherlands, 2010.Google Scholar
  61. [61]
    Schwartz S, Tung S, McMillan M. Automotive lubricants. Totten G Ed. In Fuels and Lubricants Handbook. ASTM, 2005.Google Scholar
  62. [62]
    Muller M, Fan J, Spikes H. Design of functionalized pama viscosity modifiers to reduce friction and wear in lubricating oils. ASTM Int 4(10): JAI100956 (2007)CrossRefGoogle Scholar
  63. [63]
    Kenbeek D, Buenemann T, Rieffe H. Review of organic friction modifiers—Contribution to fuel efficiency? SAE Technical Paper 2000-01-1792, Society of Automotive Engineers, Warrendale, PA, 2000.CrossRefGoogle Scholar
  64. [64]
    Stipanovic A, Schoonmaker J. The impact of organomolybdenum compounds on the frictional characteristics of crankcase engine oils. SAE Technical Paper 932779, Society of Automotive Engineers, Warrendale, PA, 1993.CrossRefGoogle Scholar
  65. [65]
    Gatto V J, Bezjak Y L. The antioxidant properties of organomolybdenum compounds in engine oils. Tribol Lubr Tech 59(10): 40–47 (2003)Google Scholar
  66. [66]
    Yao J, Aguilar G, Mazzamaro G. The friction-reducing, antiwear and antioxidation properties of an organomolybdenum lube additive without sulfur and phosphorus. Lubr Oil 22(3): 43–48 (2007)Google Scholar
  67. [67]
    Donnelly S G, Aguilar G A, Chase K J, Wallack W T. Molybdenum dialkyldithiocarbamate compositions and lubricating compositions containing the same. U. S. Patent Application 20120/0264666, 2010.Google Scholar
  68. [68]
    Ratoi M, Niste V B, Alghawel H, Suen Y F, Nelson K. The impact of organic friction modifiers on engine oil tribofilms. RSC Adv 9: 4278–4285 (2014)CrossRefGoogle Scholar
  69. [69]
    Tang Z, Li S. A review of recent developments of friction modifiers for liquid lubricants (2007–present). Current Opinion in Solid State and Materials Science 18(3): 119–139 (2014)CrossRefGoogle Scholar
  70. [70]
    Martin J-M, Grossiord C, Varlot K, Vacher B, Le Mogne T. Friction reduction mechanism of MoDTC. Nisseki Mitsubishi Rebyu 43(1): 5–11 (2001)Google Scholar
  71. [71]
    Spike H A. The history and mechanisms of ZDDP. Tribol Lett 17: 465–485 (2005)Google Scholar
  72. [72]
    Zhang Z, Yamaguchi E S, Kasrai M, Bancroft G M. Tribofilms generated from ZDDP and DDP on steel surfaces: Part1, growth, wear and morphology. Tribol Lett 19(3): 211–220 (2005)CrossRefGoogle Scholar
  73. [73]
    Zhang Z, Yamaguchi E S, Kasrai M, Bancroft G M, Liu X, Fleet M E. Tribofilms generated from ZDDP and DDP on steel surfaces: Part 2 Chemistry. Tribol Lett 19(3): 221–229 (2005)CrossRefGoogle Scholar
  74. [74]
    Esche C K, Mazzamaro G A, Bartels T, Gray D B. Fuel efficient lubricating oils. U.S. Patent Application 2015/0133352, 2015.Google Scholar
  75. [75]
    Mazzamaro G A, Donnelly S G, Hiza R J. Ultra low phosphorus lubricant composition. U.S. Patent Application 2014/0228264, 2014.Google Scholar
  76. [76]
    Onodera K, Kato T, Ogano S, Sekiyu K K, Fujimoto K, Kato K. Engine oil formulation technology to prevent preignition in turbocharged direct injection spark ignition engines. Presented at the SAE 2015 Fall Conference Powertrain, Fuels, and Lubricants, Kyoto, Japan, 2013.Google Scholar

Copyright information

© The author(s) 2016

Authors and Affiliations

  1. 1.Massachusetts Institute of TechnologyCambridgeUSA
  2. 2.Vanderbilt Chemicals LLCNorwalkUSA

Personalised recommendations