Abstract
Disc specimens manufactured from commercial bearing rollers (AISI 52100 steel, 62–63 HRC) in initial state and after pre-treatment by pulsed magnetic field (PMF) with a magnetic field strength of 1–7 MA/m were tested with sunflower oil using pin-on-disk apparatus. According to the obtained results the treatment causes a reduction in the coefficient of friction and wear. To explain the results, nano- and microhardness tests as well as optical and atomic force microscopy were used. Reasons of the effect of PMF on the friction and wear were discussed.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
http://www.ornl.gov/sci/manufacturing/research/transient_field.shtml, 2014.
Pal D K, Gupta N C. Some experimental studies on drill wear in the presence of alternating magnetic field. J Inst Eng53: 195–200 (1973)
Muju M K, Ghosh A. Effect of a magnetic-field on the diffusive wear of cutting tools. Wear58: 137–145 (1980)
El Mansori M, Klamecki B. Magnetic field effects in machining processes and on manufactured part mechanical characteristics. J Manuf Sc Eng128: 136–145 (2006)
Mohamed M K, Alahmadi A, Ali W Y, Abdel-Sattar S. Effect of magnetic field on the friction and wear displayed by the scratch of oil lubricated steel. Int J Eng Technol12: 137–143 (2012)
Bataineh O, Klamecki B E, Koepke B G. Effect of pulsed magnetic treatment on drill wear. J Mater Process Tech134: 190–196 (2003)
Baranov Yu V, Troitskii O V, Avraamov Y S, Shlyapin A D. Physical Grounds of Electric Pulse and Electric Current/Plastic Treatments and New materials (in Russian). Moscow: MGIU, 2001.
Levitin V V, Loskutov S V. The effect of a current pulse on the fatigue of titanium alloy. Sol State Commun131: 181–183 (2004)
Klamecki B E. Residual stress reduction by pulsed magnetic treatment. J Mater Process Tech141: 385–394 (2003)
Lu A L, Tang F, Luo X J, Mei J F, Fang H Z. Research on residual stress reduction by strong pulsed magnetic treatment. J Mater Process Tech74: 259–262 (1998)
Stepanov G V, Babutskii A I, Mameyev I A, Ferraris M, Casalegno V, Salvo M. Experimental evaluation of pulse electric current effect on residual stresses in composite-to-copper joints. Strength Mater40(4): 452–457 (2008)
Conrad H. Effects of electric current on solid state phase transformations in metals. Mater Sc Eng A287: 227–237 (2000)
Wu S, Zhao H, Lu A, Fang H Z, Tang F. A micro-mechanism model of residual stress reduction by low frequency alternating magnetic field treatment. J Mater Process Tech132: 198–202 (2003)
Vonsovskii S V. Magnetizm. Moscow, 1971: 776–777.
Krivoglaz M A, Sadovsky V D, Smirnov L, Fokina E A. Quenching of Steel in Magnetic Field (in Russian). Moscow: Science, 1977.
Kakeshita T, Shimizu K, Sakakibara T, Funada S, Date M. Effects of a pulsed high magnetic field on the Ms temperature and martensite morphology in an Fe-31.7at%Ni alloy. Scr Metall17: 897–900 (1983)
Ohtsuka H. Effects of a high magnetic field on Bainitic transformation in Fe-based alloys. Mat Sc Eng A438–440: 136–139 (2006)
Ludtka G M. Method for residual stress relief and retained austenite destabilization. U.S. Patent 6773513, Aug. 2014.
Lebedev A A, Muzyka N R, Volchek N L. Determination of damage accumulated in structural materials by the parameters of scatter of their hardness characteristics. Strength Mater34: 312–321 (2002)
Lebedev A A, Muzyka N R, Volchek N L, Nedoseka S A. Monitoring of current state of pipe metal in active gas pipelines. Experimental method and results. Strength Mater35: 122–127 (2003)
Frankel J, Abbate A, Scholz W. The effect of residual stresses on hardness measurements. J Exp Mech33: 164–168 (1993)
Belyakov A, Kimura Y, Tsuzaki K. Microstructure evolution in dual-phase stainless steel during severe deformation. Acta Materialia54: 2521–2532 (2006)
Yang M, Akiyama Y, Sasaki T. Evaluation of change in material properties due to plastic deformation. J Mater Process Tech151: 232–236 (2004)
Luo L, Ghosh A K. Elastic and inelastic recovery after plastic deformation of DQSK steel sheet. J Eng Mater Tech125: 237–246 (2003)
Villuendas A, Rocca A, Jorba J. Change of Young’s modulus of cold-deformed aluminium AA 1050 and of AA 2024 (T65): A comparative study. Mater Sci Forum539–534: 293–298 (2007)
Halilovič M, Vrh M, Štok B. Impact of elastic modulus degradation on springback in sheet metal forming. In Proceedings of the 9th International Conference on Numerical Methods in Industrial Forming, AIP Conference Proceedings, 2007: 925–930.
Author information
Authors and Affiliations
Corresponding author
Additional information
This article is published with open access at Springerlink.com
A preliminary version of this work was presented at the 3rd International Symposium on Tribology of IFToMM, Luleå, Sweden, 2013.
Anatolii BABUTSKYI. He received his Engineer degree in Mechanical Engineering in 1982 from Kiev Politechnic Institute, Kiev, Ukraine. In 1989 he received his Ph.D degree in Mechanical Engineering from G. S. Pisarenko Institute for Problems of Strength, National Academy of Sciences of Ukraine, Kiev, Ukraine. He joined the University of Hertfordshire, Hatfield, UK from 2011. His current position is a research fellow. His research interests include effect of electromagnetic fields on mechanical properties, corrosion, wear and friction of structural metals.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
To view a copy of this licence, visit https://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Babutskyi, A., Chrysanthou, A. & Zhao, C. Effect of pulsed magnetic field pre-treatment of AISI 52100 steel on the coefficient of sliding friction and wear in pin-on-disk tests. Friction 2, 310–316 (2014). https://doi.org/10.1007/s40544-014-0048-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40544-014-0048-0