References
Antony, J.: Simultaneous optimisation of multiple quality characteristics in manufacturing processes using Taguchi’s quality loss function. Int. J. Adv. Manuf. Technol. 17(2), 134–138 (2001)
Biswas, R., et al.: A parametric study of pulsed Nd:YAG laser micro-drilling of gamma-titanium aluminide. Opt. Laser Technol. 42(1), 23–31 (2010). doi:10.1016/j.optlastec.2009.04.011
Dubey, A.K., Yadava, V.: Multi-objective optimization of Nd: YAG laser cutting of nickel-based superalloy sheet using orthogonal array with principal component analysis. Opt. Lasers Eng. 46, 124–132 (2008)
Eltawahni, H.A., et al.: Effect of CO 2 laser cutting process parameters on edge quality and operating cost of AISI316L. Opt. Laser Technol. 44(4), 1068–1082 (2012). doi:10.1016/j.optlastec.2011.10.008
Ezugwu, E.O., Wang, Z.M.: Materials titanium alloys and their machinability. J. Mater. Process. Technol. 68, 262–274 (1997)
Garay, A., Armendia, M., Marya, S.: Machinability of titanium alloys (Ti6Al4V and Ti555.3). J. Mater. Process. Technol. 9, 2223–2230 (2009)
Goyal, R., Dubey, A.K.: Hybrid approach for modeling and optimization of hole taper during laser trepan drilling of Ti-6Al-4V alloy sheet. International Conference on Advances in Manufacturing and Materials Engineering. 5, 1781–1790 (2014)
Kuar, A.S., Doloi, B., Bhattacharyya, B.: Modelling and analysis of pulsed Nd:YAG laser machining characteristics during micro-drilling of zirconia (ZrO2). Int. J. Mach. Tools Manuf. 46(12–13), 1301–1310 (2006)
Lin, C.L.: Use of the Taguchi method and Grey relational analysis to optimize turning operations with multiple performance characteristics. Mater. Manuf. Process. 19(2), 209–220 (2004) Available at: http://www.tandfonline.com/doi/abs/10.1081/AMP-120029852
Meijer, J.: Laser beam machining ( LBM ), state of the art and new opportunities. J. Mater. Process. Technol. 149, 2–17 (2004)
Pandey, A.K., Dubey, A.K.: Taguchi based fuzzy logic optimization of multiple quality characteristics in laser cutting of Duralumin sheet. Opt. Lasers Eng. 50(3), 328–335 (2012). doi:10.1016/j.optlastec.2012.01.019
Patel, K.M., Pandey, P.M., Rao, P.V.: Optimisation of process parameters for multi-performance characteristics in EDM of Al2O3 ceramic composite. Int. J. Adv. Manuf. Technol. 47(9–12), 1137–1147 (2009). Available at: http://link.springer.com/10.1007/s00170-009-2249-7. Accessed 24 July 2014
Pramanik, A.: Problems and solutions in machining of titanium alloys. Int. J. Adv. Manuf. Technol. 70(5–8), 919–928 (2014) Available at: http://link.springer.com/article/10.1007/s00170-013-5326-x
Ross P.J.: Taguchi techniques for quality engineering, 2nd ed. McGraw-Hill Professional, New York (1996)
Samanta, S., Chakraborty, S.: Engineering applications of artificial intelligence parametric optimization of some non-traditioanal machining processes using artificial bee colony algorithm. Eng. Appl. Artif. Intell. 24(6), 946–957 (2011). doi:10.1016/j.engappai.2011.03.009
Schneider, M., et al.: Gas investigation for laser drilling. J. Laser Appl. 19(3), 165–169 (2007)
Sharma, A., Yadava, V.: Modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for curved profile. Opt. Lasers Eng. 51(1), 77–88 (2013). doi:10.1016/j.optlaseng.2012.07.012
Sharma, A., Yadava, V., Rao, R.: Optimization of kerf quality characteristics during Nd: YAG laser cutting of nickel based superalloy sheet for straight and curved cut profiles. Opt. Lasers Eng. 48(9), 915–925 (2010). doi:10.1016/j.optlaseng.2010.03.005
Tu, J., et al.: Experimental characterization of a micro-hole drilling process with short micro-second pulses by a CW single-mode fiber laser. Opt. Lasers Eng. 55, 275–283 (2014). doi:10.1016/j.optlaseng.2013.11.002
Wang, C.J., et al.: Effect of laser power on the quality of drilled micro hole using Cu50Zr50 amorphous alloys foils. Micromachines. 5(4), 1061–1068 (2014)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Avvari, M., Manjaiah, M., Able, M. et al. Optimization of Hole Characteristics During Pulse Nd:YAG Laser Drilling of Commercially Pure Titanium Alloy. Lasers Manuf. Mater. Process. 4, 76–91 (2017). https://doi.org/10.1007/s40516-017-0038-y
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40516-017-0038-y