Springer Nature is making SARS-CoV-2 and COVID-19 research free. View research | View latest news | Sign up for updates

Prediction of machining chatter in milling based on dynamic FEM simulations of chip formation

  • 508 Accesses

  • 1 Citations

Abstract

Chatter vibration is a major obstacle in achieveing increased machining performance. In this research, a finite element model of chip formation in a 2D milling process is used to predict the occurrence of chatter vibrations, and to investigate the effects of various machining parameters on this phenomenon. The dynamic properties of the machine tool at the tool tip are obtained based on experimental modal analysis, and are used in the model as the cutter dynamics. The model allows for the natural development of vibration as the result of the chip-tool engagement, and accounts for various phenomena that occur at the chip-tool interface ultimately leading to stable or unstable cutting. The model was used to demonstrate the effects of the machining parameters, such as the axial depth of cut, radial immersion, and feed rate, on the occurrence of chatter. Additionally, the phenomenon of jumping out of the cut region could be observed in this model and its effect on the chatter process is demonstrated. The numerical model is verified based on comparisons with experimental results.

This is a preview of subscription content, log in to check access.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20

References

  1. 1.

    Tobias S, Fishwick W (1958) The chatter of lathe tools under orthogonal cutting conditions. Trans ASME 80(2):1079–1088

  2. 2.

    Tlusty J, Polacek M (1963) The stability of machine tools against self-excited vibrations in machining. Int Res Prod Eng 1(1):465–474

  3. 3.

    Merritt HE (1965) Theory of self-excited machine-tool chatter: contribution to machine-tool chatter research. J Manuf Sci Eng 87(4):447–454

  4. 4.

    Sridhar R, Hohn R, Long G (1968) A general formulation of the milling process equation: contribution to machine tool chatter research 5. J Manuf Sci Eng 90(2):317–324

  5. 5.

    Hanna N, Tobias S (1974) A theory of nonlinear regenerative chatter. J Manuf Sci Eng 96(1):247–255

  6. 6.

    Wang Y, Wang T, Yu Z et al (2015) Chatter prediction for variable pitch and variable helix milling. Shock Vib. https://doi.org/10.1155/2015/419172

  7. 7.

    Moradi H, Bakhtiari-Nejad F, Movahhedy MR et al (2010) Nonlinear behaviour of the regenerative chatter in turning process with a worn tool: forced oscillation and stability analysis. Mech Mach Theory 45(8):1050–1066

  8. 8.

    Tlusty J, Zaton W, Ismail F (1983) Stability lobes in milling. CIRP Ann Manuf Technol 32(1):309–313

  9. 9.

    Mahnama M, Movahhedy M (2010) Prediction of machining chatter based on FEM simulation of chip formation under dynamic conditions. Int J Mach Tools Manuf 50(7):611–620

  10. 10.

    Mahnama M, Movahhedy MR (2012) Application of FEM simulation of chip formation to stability analysis in orthogonal cutting process. J Manuf Process 14(3):188–194

  11. 11.

    Moufki A, Devillez A, Segreti M et al (2006) A semi-analytical model of non-linear vibrations in orthogonal cutting and experimental validation. Int J Mach Tools Manuf 46(3–4):436–449

  12. 12.

    Hajmohammadi MS, Movahhedy MR, Moradi H (2014) Investigation of thermal effects on machining chatter based on FEM simulation of chip formation. CIRP J Manuf Sci Technol 7(1):1–10

  13. 13.

    Jafarzadeh E, Movahhedy MR (2017) Numerical simulation of interaction of mode-coupling and regenerative chatter in machining. J Manuf Process 27:252–260

  14. 14.

    Tlusty J, Andrews G (1983) A critical review of sensors for unmanned machining. CIRP Ann Manuf Technol 32(2):563–572

  15. 15.

    Association A (2000) Aluminum standards and data. Aluminum Association, Arlington

  16. 16.

    Brar N, Joshi V, Harris B (2009) Constitutive model constants for Al7075-T651 and Al7075-T6. Proc Am Phys Soc Top Group Shock Compres Condens Matter 1195(1):945–948

  17. 17.

    Bolar G, Joshi S (2014) Three dimensional finite element modeling and simulation of curvilinear thin-wall machining of aluminum 7075-T6 alloy. Processing and fabrication of advanced materials, World Scientific Publishing, Singapore

  18. 18.

    Tlusty J (2000) Manufacturing processes and equipment. Prentice Hall, Englewood

  19. 19.

    Insperger T, Stépán G (2004) Updated semi-discretization method for periodic delay-differential equations with discrete delay. Int J Numer Methods Eng 6(1):117–141

Download references

Author information

Correspondence to Mohammad R. Movahhedy.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Jafarzadeh, E., Movahhedy, M.R., Khodaygan, S. et al. Prediction of machining chatter in milling based on dynamic FEM simulations of chip formation. Adv. Manuf. 6, 334–344 (2018). https://doi.org/10.1007/s40436-018-0228-7

Download citation

Keywords

  • Machining chatter
  • Milling
  • Finite element model (FEM) simulation
  • Feed rate