Abstract
To improve the safety and stability of active suspension during slope conditions, sensitivity optimization is performed on the active suspension lift control system. A mathematical model of the active suspension under slope conditions is established, and the first-order trajectory sensitivity method is employed to analyze the trajectory sensitivity of the suspension lift under slope conditions. The sensitivity of each parameter corresponding to the displacement response is obtained, and sensitivity metrics are established to quantitatively analyze the degree of influence of parameter original-variations on the output dynamic characteristics. Next, a mathematical model of the position-based impedance for the suspension lift drive unit and the impedance lift sensitivity equations are established. The equations are solved to obtain the sensitivity curves and sensitivity metrics after impedance optimization. A comparison is made between the sensitivity before and after optimization, and the degree to which the parameters of the system affect the suspension lift output displacement dynamic characteristics is quantitatively analyzed after impedance optimization. The research results indicate that the variation of parameters such as the effective area of the hydraulic cylinder piston, the equivalent total volume of the hydraulic cylinder, the hydraulic oil elasticity coefficient, the pressure-flow coefficient of the proportional servo valve, the total leakage coefficient of the hydraulic cylinder, and the maximum load had a significant impact on the dynamic performance of the suspension lift drive unit. After impedance control optimization, the influence of these parameters on the dynamic performance was effectively reduced. Finally, the accuracy of the sensitivity before and after optimization was verified through semi-physical simulation experiments.
Similar content being viewed by others
References
Li JH, He J, Li XH (2014) LQG controller design for heavy vehicle active suspension based on OT-AHP Method. Appl Mech Mater 509:206–212. https://doi.org/10.4028/www.scientific.net/AMM.509.206
Xie Z, Wong PK, Zhao J et al (2015) Design of a denoising hybrid fuzzy-pid controller for active suspension systems of heavy vehicles based on model adaptive wheelbase preview strategy. J Vibroeng 17(2):883–904
Xia R, Li J, He J et al (2015) Linear-quadratic-Gaussian controller for truck active suspension based on cargo integrity. Adv Mech Eng 7(12):1–9. https://doi.org/10.1177/1687814015620320
Küçük K, Yurt HK, Arıkan KB et al (2016) Modelling and optimisation of an 8× 8 heavy duty vehicle’s hydro-pneumatic suspension system. Int J Veh Des 71(1–4):122–138. https://doi.org/10.1504/IJVD.2016.078772
Tiwari A, Lathkar M, Shendge P D, et al (2016). Skyhook control for active suspension system of heavy duty vehicles using inertial delay control[C]//2016. IEEE 1st International Conference on Power Electronics, Intelligent Control and Energy Systems (ICPEICES). IEEE, 1–6. https://doi.org/10.1109/ICPEICES.2016.7853289
Yang X, Yan L, Shen Y et al (2021) Dynamic performance analysis and parameters perturbation study of inerter–spring–damper suspension for heavy vehicle. J Low Freq Noise, Vib Act Control 40(3):1335–1350. https://doi.org/10.1177/1461348420962898
Fu Z, Gong A, Liao Z et al (2023) Anti-rollover control of heavy-duty dump truck with distributed model predictive control. Int J Heavy Veh Syst 30(2):139–166. https://doi.org/10.1504/IJHVS.2023.132310
Chen G, Jiang Y, Tang Y et al (2022) Revised adaptive active disturbance rejection sliding mode control strategy for vertical stability of active hydro-pneumatic suspension. ISA Trans 132:490–507. https://doi.org/10.1016/j.isatra.2022.06.008
Dridi I, Hamza A, Ben Yahia N (2023) Control of an active suspension system based on long short-term memory (LSTM) learning. Adv Mech Eng 15(2):1–12. https://doi.org/10.1177/16878132231156789
Bai X, Lu L, Zhang C et al (2023) Research on height adjustment characteristics of heavy vehicle active air suspension based on fuzzy control. World Electr Veh J 14(8):210. https://doi.org/10.3390/wevj14080210
Zhenkuan P, Jieyu D, Lei G (2005) Dynamic optimization design and sensitivity analysis of many-body systems. J Mech 37(005):611–619. https://doi.org/10.13306/j.1006-9798.2002.04.001
Turnip A, Park S, Hong KS (2010) Sensitivity control of a MR-damper semi-active suspension. Int J Precis Eng Manuf 11:209–218. https://doi.org/10.1007/s12541-010-0024-1
Formentin S, Karimi A (2013) A data-driven approach to mixed-sensitivity control with application to an active suspension system. IEEE Trans Ind Inform 9(4):2293–2300. https://doi.org/10.1109/TII.2012.2220556
Xiangdong K, Bin Y, Lingxiao Q et al (2013) Trajectory sensitivity analysis of hydraulic drive units for quadruped bionic robots. J Mech Eng 49(14):170–175
Xiangdong K, Bin Y, Lingxiao Q et al (2015) Sensitivity analysis of position servo control characteristic parameters for hydraulic drive units of quadruped robots in diagonal trot gait. Robot 37(1):63–73. https://doi.org/10.13973/j.cnki.robot.2015.0063
Zhou B, Chen Y, Geng Y et al (2017) Sensitivity analysis and optimization of hydraulic parameters for interconnected suspension. China Mech Eng 28(19):2269–2274
Hajdu F (2019) Sensitivity study of a nonlinear semi-active suspension system. Acta Tech Jaurinensis 12(3):205–217. https://doi.org/10.14513/actatechjaur.v12.n3.505
Abdelkareem MAA, Eldaly ABM, Ali MKA et al (2020) Monte Carlo sensitivity analysis of vehicle suspension energy harvesting in frequency domain. J Adv Res 24:53–67. https://doi.org/10.1016/j.jare.2020.02.012
Yoon DS, Kim GW, Choi SB et al (2021) Response time of magnetorheological dampers to current inputs in a semi-active suspension system: modeling, control and sensitivity analysis. Mech Syst Signal Process 146:106999. https://doi.org/10.1016/j.ymssp.2020.106999
Chen H, Gong M, Zhao D et al (2023) Sensitivity analysis and adaptive tracking control of electrohydraulic active suspension. China Mech Eng 34(04):481–489
Chu Y, Li C, Chen F (2021) Co-simulation study of electro-hydraulic proportional system based on admittance control algorithm. Mach Electron 39(05):46–51. https://doi.org/10.3969/j.issn.1001-2257.2021.05.009
Lei J, Shi X, Cai L et al (2020) Running model of single-wheel landing gear based on filtered white noise method. J Air Forc Eng Univ (Natural Science Edition) 21(03):12–18. https://doi.org/10.3969/j.issn.1009-3516.2020.03.003
Sun Y, Hou H, Li J (2022) Microscopic model test and ride comfort analysis of suspension system for mining vehicle. Constr Mach 53(02):23–27+7. https://doi.org/10.3969/j.issn.1009-3672.2022.010.580
Zhang L, Zhou J, Cheng Q et al (2018) Vehicle roll state estimation and active control considering road roughness input. J Vib Shock 37(05):133–141+154. https://doi.org/10.13465/j.cnki.jvs.2018.05.020
Jiang N, Na Dg, Chen X (2022) Fuzzy control study of semi-active suspension under random rough road conditions. J Henan Inst Eng 30(06):1–7. https://doi.org/10.3969/j.issn.2096-7772.2022.06.007
Xue J, Chen S (2021) Research on road roughness level identification based on deep learning. Mech Electr Eng Technol 50(11):66–69. https://doi.org/10.3969/j.issn.1009-9492.2021.11.015
Yao J, Jiang D, Zhang W et al (2019) First-order trajectory sensitivity analysis of open-loop pump-controlled asymmetric cylinder system. J Mech Eng 55(02):223–232. https://doi.org/10.3901/JME.2019.02.223
Pan G, Wang W (2020) Simulation study on active camber and toe of double wishbone air suspension. J Chongqing Univ Technol (Natural Science) 34(3):1–9. https://doi.org/10.3969/j.issn.1674-8425(z).2020.03.001
Meng Y, Yang W, Gan H et al (2020) Model research on electro-hydraulic proportional symmetrical valve controlled asymmetrical hydraulic cylinder. Mach Tool Hydraul 48(20):54–59+70. https://doi.org/10.3969/j.issn.1001-3881.2020.20.013
Wang F, Jiang D, Tian Y et al (2019) Sensitivity analysis of pressure relief impact in open-loop pump-controlled forging hydraulic press. High Technol Lett 29(04):379–386. https://doi.org/10.3772/j.issn.1002-0470.2019.04.009
Yu B, Ba K, Wang D et al (2018) Feedforward compensation control for hydraulic drive unit position control system. J Mech Eng 54(20):159–169. https://doi.org/10.3901/JME.2018.20.159
Funding
This research was supported by the Natural Science Foundation of the Jiangsu Higher Education Institutions of China (Grant No. 22KJB460021, 23KJA460006), Changzhou Leading Innovative Talents Introduction and Cultivation Project (Grant No. CQ20210093, CQ20220089).
Author information
Authors and Affiliations
Corresponding author
Additional information
Technical Editor: Rogério Sales Gonçalves.
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Kang, S., Kong, L., Han, C. et al. Study on the impedance of active suspension drive unit under transverse slope condition based on track sensitivity. J Braz. Soc. Mech. Sci. Eng. 46, 239 (2024). https://doi.org/10.1007/s40430-024-04795-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40430-024-04795-0