Abstract
DSS are more suitable alternatives for the applications requiring vehement resistance to corrosion in severe conditions and to stress corrosion cracking. Work hardening tendency, high toughness, design strength and built-up layer (BUL) formation contribute to machining difficulty of duplex stainless steel (DSS2205). The present investigations are aimed to detail machining performance in terms of tool wear, tool life and cutting temperatures. Comparison of performance of AlTiN coating using two advanced PVD coating deposition techniques, viz. HiPIMS and S3p, with multilayer TiN/TiAlN coating is studied. The coating deposition processes using S3p technique were carried out in a vacuum chamber at a pressure of 1.33 × 10–2 Pa to 1.33 × 10–8 Pa. AlTiN-coated tool deposited using S3p technique proved better, exhibiting the highest tool life of 7105 mm, three times more than uncoated tools, and ahead of AlTiN-coated tool deposited by HiPIMS technique (5390 mm). Among the coated tools, TiN/AlTiN-coated tools showed the highest rate of rise in cutting temperatures as 14 and 21%, for rise in cutting speeds from 100 to 140 m/min and from 140 to 180 m/min, respectively. Experimental results of cutting temperatures are found in close agreement with results of Boothroyd model within an error of ± 10%.
Graphical abstract
Similar content being viewed by others
References
ISSM (2019) Stainless steel in figures 2019. Int. Stainl. Steel Forum, pp 1–24
Gunn RN (1997) Duplex stainless steels: microstructure, properties and applications, 1st edn. Woodhead Publishing, Cambridge
Selvaraj DP, Chandrasekar P (2018) Experimental investigations of nitrogen alloyed duplex stainless steel in dry milling process. J Eng Sci Technol 13:321–331
IMoA (2014) Practical guidelines for the fabrication of duplex stainless steels, 3rd edn. International Molybdenum Association (IMoA), London
SubhashSoumya N, Soumya S, Raj N, Jagadeesha T (2019) Experimental study on tool wear and optimization of process parameters using ANN-GA in turning of super-duplex stainless steel under dry and wet conditions. Adv Manuf Technol. https://doi.org/10.1007/978-981-13-6374-0_47
Królczyk G, Gajek M, Legutko S (2013) Effect of the cutting parameters impact on tool life in duplex stainless steel turning process. Teh Vjesn 20:587–592
Nilsson J-O (1992) Overview super duplex stainless steels. Mater Sci Technol 8:685–700. https://doi.org/10.1179/mst.1992.8.8.685
Voronenko B (1997) Austenitic-ferritic stainless steels: a state of the art review. Met Sci Heat Treat 39:428–437. https://doi.org/10.1007/BF02484228
Nomani J, Pramanik A, Hilditch T, Littlefair G (2017) Stagnation zone during the turning of duplex SAF 2205 stainless steels alloy. Mater Manuf Process 32:1486–1489. https://doi.org/10.1080/10426914.2017.1279289
Selvaraj PD, Chandramohan P, Mohanraj M (2014) Optimization of surface roughness, cutting force and tool wear of nitrogen alloyed duplex stainless steel in a dry turning process using Taguchi method. Meas J Int Meas 49:205–215. https://doi.org/10.1016/j.measurement.2013.11.037
Krolczyk G, Nieslony P, Legutko S (2014) Microhardness and surface integrity in turning process of duplex stainless steel (DSS) for different cutting conditions. J Mater Eng Perform 23:859–866. https://doi.org/10.1007/s11665-013-0832-4
Koyee RD, Heisel U, Schmauder S, Eisseler R (2014) Experimental investigation and multiobjective optimization of turning duplex stainless steels. Int J Manuf Eng 1:1–13
Soumya S, Subhash N, Raj N, Jagadeesha T (2019) Experimental study on surface roughness and optimization of process parameters using ANN-GA in milling of super-duplex stainless steel under dry and wet conditions. Adv Manuf Technol. https://doi.org/10.1007/978-981-13-6374-0_46
Kulkarni AP, Sargade VG (2015) Characterization and performance of AlTiN, AlTiCrN, TiN/TiAlN PVD coated carbide tools while turning SS 304. Mater Manuf Process 30:748–755. https://doi.org/10.1080/10426914.2014.984217
Sonawane GD, Sargade VG (2019) Evaluation and multi-objective optimization of nose wear, surface roughness and cutting forces using grey relation analysis (GRA). J Braz Soc Mech Sci Eng 41:1–13. https://doi.org/10.1007/s40430-019-2057-4
Bunshah R (2002) Handbook of hard coatings. William Andrew Publishing
He HB, Han WQ, Li HY, Li DY, Yang J, Gu T, Deng T (2014) Effect of deep cryogenic treatment on machinability and wear mechanism of TiAlN coated tools during dry turning. Int J Precis Eng Manuf 15:655–660. https://doi.org/10.1007/s12541-014-0384-z
Staszuk M, Pakuła D, Chladek G, Pawlyta M, Pancielejko M, Czaja P (2018) Investigation of the structure and properties of PVD coatings and ALD + PVD hybrid coatings deposited on sialon tool ceramics. Vacuum 154:272–284. https://doi.org/10.1016/j.vacuum.2018.04.032
Galanis D (2008) Comparison between dry and wet machining of stainless steel. In: Bouzakis PK-D (ed) Proc. 3rd Int. Conf. Manuf. Eng., Aristoteles University of Thessaloniki and Project Center Coatings in Manufacturing (PCCM), Greece, pp 1–3
Sonawane GD, Sargade VG (2020) Machinability study of duplex stainless steel 2205 during dry turning. Int J Precis Eng Manuf. https://doi.org/10.1007/s12541-019-00305-8
Diniz AE, Micaroni R (2002) Cutting conditions for finish turning process aiming: the use of dry cutting. Int J Mach Tools Manuf 42:899–904
Krolczyk G, Nieslony AP, Maruda RW (2016) Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production. J Clean Prod 30:1–12
Thiele JD, Melkote S (1999) Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J Mater Process Technol 94:216–226. https://doi.org/10.1016/S0924-0136(99)00111-9
Castro G, Almeida FA, Oliveira FJ, Fernandes AJS, Sacramento J, Silva RF (2008) Dry machining of silicon-aluminium alloys with CVD diamond brazed and directly coated Si3N4 ceramic tools. Vacuum 82:1407–1410. https://doi.org/10.1016/j.vacuum.2008.03.042
Kelly PJ, Arnell RD (2000) Magnetron sputtering: a review of recent developments and applications. Vacuum 56:159–172. https://doi.org/10.1016/S0042-207X(99)00189-X
Voevodin AA, Zabinski JS (2005) Nanocomposite and nanostructured tribological materials for space applications. Compos Sci Technol 65:741–748. https://doi.org/10.1016/J.COMPSCITECH.2004.10.008
Rajaguru J, N. Arunachalam J (2017) Coated tool performance in dry turning of super duplex stainless steel. In: 45th SME North Am. Manuf. Res. Conf. NAMRC 45, LA, USA. Elsevier, pp 601–611. https://doi.org/10.1016/J.PROMFG.2017.07.061
Krolczyk GM, Nieslony P, Legutko S (2015) Determination of tool life and research wear during duplex stainless steel turning. Arch Civ Mech Eng 15:347–354. https://doi.org/10.1016/j.acme.2014.05.001
Inspektor A, Salvador PA (2014) Architecture of PVD coatings for metalcutting applications: a review. Surf Coat Technol 257:138–153. https://doi.org/10.1016/j.surfcoat.2014.08.068
Barshilia HC, Deepthi B, Selvakumar N, Jain A, Rajam KS (2007) Nanolayered multilayer coatings of CrN/CrAlN prepared by reactive DC magnetron sputtering. Appl Surf Sci 253:5076–5083
Chang YY, Yang SJ, Wang DY (2006) Structural and mechanical properties of AlTiN/CrN coatings synthesized by a cathodic-arc deposition process. Surf Coat Technol 201:4209–4214. https://doi.org/10.1016/j.surfcoat.2006.08.062
Chen L, Du Y, Yin F, Li J (2007) Mechanical properties of (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings. Int J Refract Met Hard Mater 25:72–76. https://doi.org/10.1016/j.ijrmhm.2006.01.005
Vetter J (2014) Innovative PVD processes for advanced coatings based on HiPIMS and arc: scalable pulsed power plasma and high ionization triple. In: Funct. Coatings Surf. Eng., Oerlikon Balzer, Montreal, Canada, pp 1–20
Abhang LB, Hameedullah M (2018) Modeling and analysis of tool wear based on cutting force and chip-tool interface temperatures in turning. In: Adv. Manuf. Mater. Sci.. Springer, Berlin, pp 411–420. https://doi.org/10.1007/978-3-319-76276-0
Donnet C, Erdemir A (2004) Historical developments and new trends in tribological and solid lubricant coatings. Surf Coat Technol. https://doi.org/10.1016/j.surfcoat.2003.10.022
Slusarczyk L (2017) The implementation of a thermal imaging camera for testing the temperature of the cutting zone in turning. In: Photonics Appl. Astron. Commun. Ind. High-Energy Phys. Exp., pp 1–6. https://doi.org/10.1117/12.2249298
Bhirud NL, Gawande RR (2017) Measurement and prediction of cutting temperatures during dry milling: review and discussions. J Braz Soc Mech Sci Eng 39:5135–5158. https://doi.org/10.1007/s40430-017-0869-7
Petkovik D, Madic M, Jankovik P, GM R (2016) Modelling of cutting temparatures in the biomedical stainless steel turning process. Themal Sci 20:1345–1354
Boothroyd G (2017) Fundamentals of machining and machine tools, 3rd edn. Taylor and Francis, London
Davim JP (ed) (2011) Davim, machining of hard materials. Springer, London
Rupetsov V, Minchev R (2016) Experimental calo tester for the coating thickness measurement. In: XV Int. Sci. Conf., pp 188–192
Baptista A, Silva F, Porteiro J, Míguez J, Pinto G (2018) Sputtering physical vapour deposition (PVD) coatings: a critical review on process improvement and market trend demands. Coatings. https://doi.org/10.3390/COATINGS8110402
Bujak J, Walkowicz J, Kusiński J (2004) Influence of the nitrogen pressure on the structure and properties of (Ti, Al)N coatings deposited by cathodic vacuum arc PVD process. Surf Coat Technol 180–181:150–157. https://doi.org/10.1016/j.surfcoat.2003.10.058
Chen L, Xu YX, Du Y, Liu Y (2015) Effect of bilayer period on structure, mechanical and thermal properties of TiAlN/AlTiN multilayer coatings. Thin Solid Films 592:207–214. https://doi.org/10.1016/j.tsf.2015.09.029
Zha X, Jiang F, Xu X (2017) Investigation of modelling and stress distribution of a coating/substrate system after an indentation test. Int J Mech Sci 134:1–14. https://doi.org/10.1016/j.ijmecsci.2017.10.002
de Paiva JMF, Torres RD, Amorim FL, Covelli D, Tauhiduzzaman M, Veldhuis S, Dosbaeva G, Fox-Rabinovich G (2017) Frictional and wear performance of hard coatings during machining of superduplex stainless steel. Int J Adv Manuf Technol 92:423–432. https://doi.org/10.1007/s00170-017-0141-4
Hao G, Liu Z, Liang X, Zhao J (2019) Influences of TiAlN coating on cutting temperature during orthogonal machining H13 hardened steel. Coatings. https://doi.org/10.3390/coatings9060355
Zha X, Chen F, Jiang F, Xu X (2019) Correlation of the fatigue impact resistance of bilayer and nanolayered PVD coatings with their cutting performance in machining Ti–6Al–4V. Ceram Int 45:14704–14717
Guo B, Zhang L, Cao L, Zhang T, Jiang F, Yan L (2017) The correction of temperature-dependent vickers hardness of cemented carbide base on the developed high-temperature hardness tester. J Mater Process Technol. https://doi.org/10.1016/j.jmatprotec.2017.12.041
Boing D, de Oliveira AJ, Schroeter RB (2020) Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning. Int J Adv Manuf Technol 106:5441–5451. https://doi.org/10.1007/s00170-020-05000-x
Zha X, Jiang F, Xu X (2018) Investigating the high frequency fatigue failure mechanisms of mono and multilayer PVD coatings by the cyclic impact tests. Surf Coat Technol. https://doi.org/10.1016/j.surfcoat.2018.03.101
Mia M (2018) Mathematical modeling and optimization of MQL assisted end milling characteristics based on RSM and Taguchi method. Measurement 121:249–260. https://doi.org/10.1016/J.MEASUREMENT.2018.02.017
Acknowledgements
The authors would like to express gratitude to CemeCon, Germany, and Balzer, India, for providing timely support regarding coating of cutting tools.
Funding
This work was supported by the NEB and Department of Science and Technology (DST), Govt. of India, under the grant ref: 11/10/2015-NEB (G)/03 dated 27/09/2017.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that there is no conflict of interest, and authors have full control of all the data included in the manuscript, and authors are agree to allow this journal to review their data, if required.
Ethical approval
The manuscript does not contain any clinical studies or patient data.
Additional information
Technical Editor: Izabel Fernanda Machado.
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Sonawane, G.D., Nipanikar, S.R. & Sargade, V.G. Characterization and experimental evaluation of PVD AlTiN and TiN/TiAlN coatings for dry turning of DSS2205. J Braz. Soc. Mech. Sci. Eng. 44, 479 (2022). https://doi.org/10.1007/s40430-022-03775-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40430-022-03775-6