Skip to main content
SpringerLink
Log in

Development of a new model for determine of cutting parameters in metal drilling processes

  • Technical Paper
  • Published:
Journal of the Brazilian Society of Mechanical Sciences and Engineering Aims and scope Submit manuscript

Abstract

Metal drilling and cutting processes are used commonly in many areas of the industry. When these processes investigated analytically, it is seen that they have a very complicated structure. This complicated structure can find easy solutions with finite element-based simulation tools. In metal removal operations, it is very difficult to calculate the cutting parameters such as cutting tool stresses, residual stresses, cutting tool–chip interface temperature and shear angle both experimentally and analytically. But, these operations could be easily calculated by computer-supported simulation tools. In these types of numeric simulations, using finite element method, it is needed to identify clearly the friction, material model load and limiting conditions. In this paper, the cutting parameters as cutting and thrust power, heat transfer coefficient and friction coefficient at chip–tool interface which is needed to find the temperature distribution on drilling bit and workpiece material were calculated using analytic models.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19

Similar content being viewed by others

References

  1. Yen YC, Jain A, Chigurupati P, Wu WT, Altan T (2004) Computer simulation of orthogonal cutting using a tool with multiple coatings. Mach Sci Technol 8(2):305–326. https://doi.org/10.1081/mst-200029230

    Article  Google Scholar 

  2. Kang JH, Lee KO, Kang SS (2007) Heat transfer coefficient for F.E analysis in the warm forging process. JAMME 20(1–2):367–370

    Google Scholar 

  3. Ceretti E, Filice L, Umbrello D, Micari F (2007) ALE simulation of orthogonal cutting: a new approach to model heat transfer phenomena at the tool–chip interface. CIRP Ann Manuf Technol 56(1):69–72. https://doi.org/10.1016/j.cirp.2007.05.019

    Article  Google Scholar 

  4. Ulutan D, Lazoglu I, Dinc C (2009) Three-dimensional temperature predictions in machining processes using finite difference method. J Mater Process Technol 209(2):1111–1121. https://doi.org/10.1016/j.jmatprotec.2008.03.020

    Article  Google Scholar 

  5. Kara S, Li W (2011) Unit process energy consumption models for material removal processes. CIRP Ann Manuf Technol 60(1):37–40. https://doi.org/10.1016/j.cirp.2011.03.018

    Article  Google Scholar 

  6. Bayoumi AE, Yücesan G, Hutton DV (1994) On the closed form mechanistic modeling of milling: specific cutting energy, torque, and power. JMEP 3(1):151–158. https://doi.org/10.1007/bf02654511

    Article  Google Scholar 

  7. Özel T, Altan T (2000) Determination of workpiece flow stress and friction at the chip–tool contact for high-speed cutting. Int J Mach Tool Manuf 40(1):133–152. https://doi.org/10.1016/S0890-6955(99)00051-6

    Article  Google Scholar 

  8. Gok K, Inal S, Gok A, Pinar AM (2016) Biomechanical effects of three different configurations in Salter Harris type 3 distal femoral epiphyseal fractures. J Braz Soc Mech Sci Eng. https://doi.org/10.1007/s40430-016-0666-8

    Article  Google Scholar 

  9. Gok K (2015) Development of three-dimensional finite element model to calculate the turning processing parameters in turning operations. Measurement 75:57–68. https://doi.org/10.1016/j.measurement.2015.07.034

    Article  Google Scholar 

  10. Inal S, Taspinar F, Gulbandilar E, Gok K (2015) Comparison of the biomechanical effects of pertrochanteric fixator and dynamic hip screw on an intertrochanteric femoral fracture using the finite element method. Int J Med Robot Comput Assist Surg 11(1):95–103

    Article  Google Scholar 

  11. Erdem M, Gok K, Gokce B, Gok A (2016) Numerical analysis of temperature, screwing moment and thrust force using finte element method in bone screwing process. J Mech Med Biol 17(01):1750016

    Article  Google Scholar 

  12. Gok K, Gok A, Kisioglu Y (2014) Optimization of processing parameters of a developed new driller system for orthopedic surgery applications using Taguchi method. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-014-6327-0

    Article  Google Scholar 

  13. Afsar E, Taspinar F, Calik BB, Ozkan Y, Gok K (2016) Use of the finite element analysis to determine stresses in the knee joints of osteoarthritis patients with different Q angles. J Braz Soc Mech Sci Eng 39:1–7

    Google Scholar 

  14. Gok K, Taspinar F, Inal S, Gulbandilar E (2015) Importance of sidebar-bone spacing during the application of pertrochanteric fixator on femoral intertrochanteric fracture model; comparison of the biomechanical effects using finite element method. Biomed Eng Appl Basis Commun 27(03):1550030

    Article  Google Scholar 

  15. Nagaraj M, Kumar AJP, Ezilarasan C, Betala R (2019) Finite element modeling in drilling of nimonic C-263 alloy using deform-3D. Comput Model Eng Sci 118(3):679–692. https://doi.org/10.31614/cmes.2019.04924

    Article  Google Scholar 

  16. Akhbar MFA, Yusoff AR (2019) Multi-objective optimization of surgical drill bit to minimize thermal damage in bone-drilling. Appl Therm Eng 157:113594. https://doi.org/10.1016/j.applthermaleng.2019.04.004

    Article  Google Scholar 

  17. Wei L, Wang D (2019) Comparative study on drilling effect between conventional drilling and ultrasonic-assisted drilling of Ti-6Al-4 V/Al2024-T351 laminated material. Int J Adv Manuf Technol 103(1):141–152. https://doi.org/10.1007/s00170-019-03507-6

    Article  Google Scholar 

  18. Altintas Y (2012) Manufacturing automation: metal cutting mechanics, machine tool vibrations, and CNC design. Cambridge University Press, Cambridge

    Google Scholar 

  19. Armarego EJA, Brown RH (1969) The machining of metals. Prentice-Hall, Upper Saddle River. http://worldcat.org. http://books.google.com/books?id=Rd5SAAAAMAAJ. Accessed 10 June 2016

  20. http://perso.crans.org/epalle/M2/MFNA/SNECMA_14.5_L08_Mesh_Quality.pdf (2016). Accessed 24 July 2016

  21. Pashazadeh H, Masoumi A, Teimournezhad J (2013) A 3D numerical model to investigate mechanical, thermal, and material flow characteristics in friction stir welding of copper sheets. Int J Automot Eng 3:328–342

    Google Scholar 

  22. DEFORM-3D DEFORM-3D Material Library. https://www.deform.com/products/deform-3d/. Accessed 14 June 2016

  23. Gok A, Gok K, Bilgin MB (2015) Three-dimensional finite element model of the drilling process used for fixation of Salter-Harris type-3 fractures by using a K-wire. Mech Sci 6(2):147–154. https://doi.org/10.5194/ms-6-147-2015

    Article  Google Scholar 

Download references

Funding

There is no funding.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Engineering Faculty, Kırklareli University, Kırklareli, Turkey

    Erol Türkes

  2. Kütahya Vocational School of Technical Sciences, Kütahya Dumlupinar University, Germiyan Campus, Kütahya, Turkey

    Mehmet Erdem

  3. Department of Biomedical Engineering, Engineering and Architecture Faculty, Izmir Bakircay University, Izmir, Turkey

    Kadir Gok

  4. Department of Mechanical Engineering, Technology Faculty, Amasya University, Amasya, Turkey

    Arif Gok

Authors
  1. Erol Türkes
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Mehmet Erdem
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Kadir Gok
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Arif Gok
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Kadir Gok.

Ethics declarations

Conflict of interest

There is no conflict of interest.

Additional information

Technical Editor: Adriano Fagali de Souza.

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Türkes, E., Erdem, M., Gok, K. et al. Development of a new model for determine of cutting parameters in metal drilling processes. J Braz. Soc. Mech. Sci. Eng. 42, 169 (2020). https://doi.org/10.1007/s40430-020-2257-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s40430-020-2257-y

Keywords

Search

Navigation