Advertisement

Forming force in incremental sheet forming: a comparative analysis of the state of the art

  • Ajay KumarEmail author
  • Vishal Gulati
  • Parveen Kumar
  • Hari Singh
Review
  • 73 Downloads

Abstract

Incremental sheet forming (ISF) significantly exempts use of expensive dies and reduces tooling cost for manufacturing complex parts in the field of sheet metal forming which makes it suitable for manufacturing prototypes and low volume production as compared to other traditional sheet metal forming processes. ISF also finds suitability for producing components of old machinery, which are otherwise very difficult to form due to the unavailability of forming dies. Moreover, the incremental nature of the process and local deformation of the sheet ensures higher formability and lower required forming force. To take advantages of lower required forming force, it is important to minimize and estimate forming force through the manipulation of the parameters for the safe utilization of hardware. In this review article, a literature survey was carried out quantitatively to study different aspects of ISF, especially to show different process parameters and techniques that affect the forming forces significantly. The current state of the art of the ISF process has been discussed with detailed analysis of process capabilities and limitations in terms of forming forces. Influences of different process parameters and forming techniques have also been studied on forming forces. Some parameters have shown their significance to control the forming force in order to preserve forming machinery. A lack of focus was found on effects of some important forming process parameters and methods, which could have been crucial for safe utilization of forming hardware. A number of guidelines have been recommended for future research work. Appropriate guidelines have also been suggested regarding the relationship between process parameters and forming forces developed during the process in order to ensure the applicability of the ISF process on the industrial scale.

Keywords

Incremental sheet forming Forming force Process parameters Forming techniques Finite element analysis 

Notes

Compliance with ethical standards

Conflict of interest

The authors have no conflict of interest.

References

  1. 1.
    Kumar A, Gulati V (2019) Experimental investigation and optimization of surface roughness in negative incremental forming. Measurement 131:419–430Google Scholar
  2. 2.
    Li P, He J, Liu Q, Yang M, Wang Q, Yuan Q, Li Y (2017) Evaluation of forming forces in ultrasonic incremental sheet metal forming. Aerosp Sci Technol 63:132–139Google Scholar
  3. 3.
    Kumar A, Gulati V, Kumar P (2018) Investigation of surface roughness in incremental sheet forming. Proc Comput Sci 133:1014–1020Google Scholar
  4. 4.
    Bagudanch I, Centeno G, Vallellano C, Garcia-Romeu ML (2013) Forming force in single point incremental forming under different bending conditions. Proc Eng 63:354–360Google Scholar
  5. 5.
    Li Y, Daniel WJ, Meehan PA (2017) Deformation analysis in single-point incremental forming through finite element simulation. Int J Adv Manuf Technol 88(1–4):255–267Google Scholar
  6. 6.
    Blaga A, Bologa O, Oleksik V, Breaz R (2011) Influence of tool path on main strains, thickness reduction and forces in single point incremental forming process. Proc Manuf Syst 6(4):191–196Google Scholar
  7. 7.
    Kumar A, Gulati V, Kumar P (2018) Investigation of process variables on forming forces in incremental sheet forming. Int J Eng Technol 10:680–684Google Scholar
  8. 8.
    Kumar A, Gulati V (2018) Experimental investigations and optimization of forming force in incremental sheet forming. Sādhanā 43(10):159Google Scholar
  9. 9.
    Kumar A, Gulati V, Kumar P (2018) Effects of process parameters on surface roughness in incremental sheet forming. Mater Today Proc 5:28026–28032Google Scholar
  10. 10.
    Araghi BT, Manco GL, Bambach M, Hirt G (2009) Investigation into a new hybrid forming process: incremental sheet forming combined with stretch forming. CIRP Ann 58(1):225–228Google Scholar
  11. 11.
    Skjødt M, Bay N, Endelt B, Ingarao G (2008) Multi stage strategies for single point incremental forming of a cup. Int J Mater Form 1(1):1199–1202Google Scholar
  12. 12.
    Kumar A, Gulati V, Kumar P, Singh V, Kumar B, Singh H (2018) Parametric effects on formability of AA2024-O aluminum alloy sheets in single point incremental forming. J Mater Res Technol.  https://doi.org/10.1016/j.jmrt.2018.11.001 CrossRefGoogle Scholar
  13. 13.
    Skjødt M, Silva MB, Martins PAF, Bay N (2009) Formability in multistage single point incremental forming. In: 7th ESMC2009: The 7th euromech solids mechanics conferenceGoogle Scholar
  14. 14.
    Kitazawa K, Wakabayashi A, Murata K, Yaejima K (1996) Metal-flow phenomena in computerized numerically controlled incremental stretch-expanding of aluminum sheets. Jpn Inst Light Metals J 46(2):65–70Google Scholar
  15. 15.
    Kitazawa K, Nakane M (1997) Hemi-ellipsoidal stretch-expanding of aluminum sheet by CNC incremental forming process with two path method. Jpn Inst Light Metals J 47:440–445Google Scholar
  16. 16.
    Young D, Jeswiet J (2004) Wall thickness variations in single-point incremental forming. Proc Inst Mech Eng Part B J Eng Manuf 218(11):1453–1459Google Scholar
  17. 17.
    Hirt G, Ames J, Bambach M, Kopp R (2004) Forming strategies and process modelling for CNC incremental sheet forming. CIRP Ann Manuf Technol 53(1):203–206Google Scholar
  18. 18.
    Malhotra R, Bhattacharya A, Kumar A, Reddy NV, Cao J (2011) A new methodology for multi-pass single point incremental forming with mixed toolpaths. CIRP Ann Manuf Technol 60(1):323–326Google Scholar
  19. 19.
    Li J, Hu J, Pan J, Geng P (2012) Thickness distribution and design of a multi-stage process for sheet metal incremental forming. Int J Adv Manuf Technol 62(9–12):981–988Google Scholar
  20. 20.
    Junchao L, Junjian S, Bin W (2013) A multipass incremental sheet forming strategy of a car taillight bracket. Int J Adv Manuf Technol 69(9–12):2229–2236Google Scholar
  21. 21.
    Cerro I, Maidagan E, Arana J, Rivero A, Rodriguez PP (2006) Theoretical and experimental analysis of the dieless incremental sheet forming process. J Mater Process Technol 177(1–3):404–408Google Scholar
  22. 22.
    Jeswiet J, Duflou JR, Szekeres A (2005) Forces in single point and two point incremental forming. Adv Mater Res 6:449–456Google Scholar
  23. 23.
    Fan G, Gao L, Hussain G, Wu Z (2008) Electric hot incremental forming: a novel technique. Int J Mach Tools Manuf 48(15):1688–1692Google Scholar
  24. 24.
    Suresh K, Regalla SP (2014) Effect of mesh parameters in finite element simulation of single point incremental sheet forming process. Proc Mater Sci 6:376–382Google Scholar
  25. 25.
    Bouffioux C, Pouteau P, Duchene L, Vanhove H, Duflou JR, Habraken AM (2010) Material data identification to model the single point incremental forming process. Int J Mater Form 3(1):979–982Google Scholar
  26. 26.
    Li Y, Liu Z, Lu H, Daniel WB, Liu S, Meehan PA (2014) Efficient force prediction for incremental sheet forming and experimental validation. Int J Adv Manuf Technol 73(1–4):571–587Google Scholar
  27. 27.
    Azevedo NG, Farias JS, Bastos RP, Teixeira P, Davim JP, de Sousa RJA (2015) Lubrication aspects during single point incremental forming for steel and aluminum materials. Int J Precis Eng Manuf 16(3):589–595Google Scholar
  28. 28.
    Callegari M, Gabrielli A, Palpacelli MC, Principi M (2008) Incremental forming of sheet metal by means of parallel kinematics machines. J Manuf Sci Eng 130(5):054501Google Scholar
  29. 29.
    Meier H, Buff B, Laurischkat R, Smukala V (2009) Increasing the part accuracy in dieless robot-based incremental sheet metal forming. CIRP Ann 58(1):233–238Google Scholar
  30. 30.
    Schafer T, Dieter Schraft R (2005) Incremental sheet metal forming by industrial robots. Rapid Prototyp J 11(5):278–286Google Scholar
  31. 31.
    Chera I, Bologa O, Racz G, Breaz R, Crenganis M (2013) FEM researches regarding incremental forming process. Ann Oradea Univ Fascicle Manag Technol Eng 1:53–58Google Scholar
  32. 32.
    Belchior J, Guines D, Leotoing L, Ragneau E (2013) Force prediction for correction of robot tool path in single point incremental forming. Key Eng Mater 554:1282–1289Google Scholar
  33. 33.
    Belchior J, Leotoing L, Guines D, Courteille E, Maurine P (2014) A process/machine coupling approach: application to robotized incremental sheet forming. J Mater Process Technol 214(8):1605–1616Google Scholar
  34. 34.
    Mohammadi A, Qin L, Vanhove H, Seefeldt M, Van Bael A, Duflou JR (2016) Single point incremental forming of an aged AL-Cu-Mg alloy: influence of pre-heat treatment and warm forming. J Mater Eng Perform 25(6):2478–2488Google Scholar
  35. 35.
    Duflou JR, Callebaut B, Verbert J, De Baerdemaeker H (2008) Improved SPIF performance through dynamic local heating. Int J Mach Tools Manuf 48(5):543–549Google Scholar
  36. 36.
    Al-Obaidi A, Kräusel V, Landgrebe D (2016) Hot single-point incremental forming assisted by induction heating. Int J Adv Manuf Technol 82(5–8):1163–1171Google Scholar
  37. 37.
    Xu D, Lu B, Cao T, Chen J, Long H, Cao J (2014) A comparative study on process potentials for frictional stir-and electric hot-assisted incremental sheet forming. Proc Eng 81:2324–2329Google Scholar
  38. 38.
    Honarpisheh M, Abdolhoseini MJ, Amini S (2016) Experimental and numerical investigation of the hot incremental forming of Ti-6Al-4 V sheet using electrical current. Int J Adv Manuf Technol 83(9–12):2027–2037Google Scholar
  39. 39.
    Duflou JR, Callebaut B, Verbert J, De Baerdemaeker H (2007) Laser assisted incremental forming: formability and accuracy improvement. CIRP Ann Manuf Technol 56(1):273–276Google Scholar
  40. 40.
    Skjoedt M, Hancock MH, Bay N (2007) Creating 3D forming. Key Eng Mater 344:583–590Google Scholar
  41. 41.
    Attanasio A, Ceretti E, Giardini C (2006) Optimization of tool path in two points incremental forming. J Mater Process Technol 177(1–3):409–412Google Scholar
  42. 42.
    Jadhav S (2004) Basic investigations of the incremental sheet metal forming process on a CNC milling machine, Dr.-Ing. Diss. Dissertation, University of DortmundGoogle Scholar
  43. 43.
    Suresh K, Khan A, Regalla SP (2013) Tool path definition for numerical simulation of single point incremental forming. Proc Eng 64:536–545Google Scholar
  44. 44.
    Fu Z, Mo J, Han F, Gong P (2013) Tool path correction algorithm for single-point incremental forming of sheet metal. Int J Adv Manuf Technol 64(9–12):1239–1248Google Scholar
  45. 45.
    Lu B, Chen J, Ou H, Cao J (2013) Feature-based tool path generation approach for incremental sheet forming process. J Mater Process Technol 213(7):1221–1233Google Scholar
  46. 46.
    Blaga A, Oleksik V (2013) A study on the influence of the forming strategy on the main strains, thickness reduction, and forces in a single point incremental forming process. Adv Mater Sci Eng.  https://doi.org/10.1155/2013/382635 CrossRefGoogle Scholar
  47. 47.
    Thibaud S, Hmida RB, Richard F, Malécot P (2012) A fully parametric toolbox for the simulation of single point incremental sheet forming process: numerical feasibility and experimental validation. Simul Model Pract Theory 29:32–43Google Scholar
  48. 48.
    Arfa H, Bahloul R, BelHadjSalah H (2013) Finite element modelling and experimental investigation of single point incremental forming process of aluminum sheets: influence of process parameters on punch force monitoring and on mechanical and geometrical quality of parts. Int J Mater Form 6(4):483–510Google Scholar
  49. 49.
    Asghar J, Reddy NV (2013) Importance of tool configuration in incremental sheet metal forming of difficult to form materials using electro-plasticity. In: Proceedings of the world congress on engineering, vol 3, pp 1734–1738Google Scholar
  50. 50.
    Liu Z, Li Y, Meehan PA (2013) Experimental investigation of mechanical properties, formability and force measurement for AA7075-O aluminum alloy sheets formed by incremental forming. Int J Precis Eng Manuf 14(11):1891–1899Google Scholar
  51. 51.
    Pohlak M, Majak J, Küttner R (2007) Manufacturability and limitations in incremental sheet forming. Proc Estonian Acad Sci Eng 13(2):129–139Google Scholar
  52. 52.
    Matsubara S (1994) Incremental backward bulge forming of a sheet metal with a hemispherical head tool-a study of a numerical control forming system II. J Jpn Soc Technol Plast 35(406):1311–1316Google Scholar
  53. 53.
    Amino H, Lu Y, Maki T, Osawa S, Fukuda K (2002) Dieless NC forming, prototype of automotive service parts. In: Proceedings of the 2nd international conference on rapid prototyping and manufacturing (ICRPM), BeijingGoogle Scholar
  54. 54.
    Li Y, Daniel WJ, Liu Z, Lu H, Meehan PA (2015) Deformation mechanics and efficient force prediction in single point incremental forming. J Mater Process Technol 221:100–111Google Scholar
  55. 55.
    Al-Ghamdi KA, Hussain G (2015) Forming forces in incremental forming of a geometry with corner feature: investigation into the effect of forming parameters using response surface approach. Int J Adv Manuf Technol 76(9–12):2185–2197Google Scholar
  56. 56.
    Al-Ghamdi KA, Hussain G, Butt SI (2014) Force variations with defects and a force-based strategy to control defects in SPIF. Mater Manuf Process 29(10):1197–1204Google Scholar
  57. 57.
    Blaga A, Bologa O, Oleksik V, Pirvu B (2012) Experimental researches regarding the influence of geometric parameters on the principal strains and thickness reduction in single point incremental forming. Bull Ser D 74(2):111–120Google Scholar
  58. 58.
    Filice L, Ambrogio G, Micari F (2006) On-line control of single point incremental forming operations through punch force monitoring. CIRP Ann Manuf Technol 55(1):245–248Google Scholar
  59. 59.
    Aerens R, Eyckens P, Van Bael A, Duflou JR (2010) Force prediction for single point incremental forming deduced from experimental and FEM observations. Int J Adv Manuf Technol 46(9–12):969–982Google Scholar
  60. 60.
    Duflou J, Tunckol Y, Szekeres A, Vanherck P (2007) Experimental study on force measurements for single point incremental forming. J Mater Process Technol 189(1–3):65–72Google Scholar
  61. 61.
    Bagudanch I, Garcia-Romeu ML, Centeno G, Elías-Zúñiga A, Ciurana J (2015) Forming force and temperature effects on single point incremental forming of polyvinylchloride. J Mater Process Technol 219:221–229Google Scholar
  62. 62.
    Centeno G, Bagudanch I, Martínez-Donaire AJ, Garcia-Romeu ML, Vallellano C (2014) Critical analysis of necking and fracture limit strains and forming forces in single-point incremental forming. Mater Des 63:20–29Google Scholar
  63. 63.
    Petek A, Kuzman K, Kopac J (2009) Deformations and forces analysis of single point incremental sheet metal forming. Arch Mater Sci Eng 35(2):107–116Google Scholar
  64. 64.
    Ambrogio G, Filice L, Micari F (2006) A force measuring based strategy for failure prevention in incremental forming. J Mater Process Technol 177(1–3):413–416Google Scholar
  65. 65.
    Duflou JR, Szekeres A, Vanherck P (2005) Force measurements for single point incremental forming: an experimental study. Adv Mater Res 6:441–448Google Scholar
  66. 66.
    Wang J, Nair M, Zhang Y (2016) An efficient force prediction strategy in single point incremental sheet forming. Proc Manuf 5:761–771Google Scholar
  67. 67.
    Durante M, Formisano A, Langella A (2011) Observations on the influence of tool-sheet contact conditions on an incremental forming process. J Mater Eng Perform 20(6):941–946Google Scholar
  68. 68.
    Li Y, Liu Z, Daniel WJT, Meehan PA (2014) Simulation and experimental observations of effect of different contact interfaces on the incremental sheet forming process. Mater Manuf Process 29(2):121–128Google Scholar
  69. 69.
    Ziran X, Gao L, Hussain G, Cui Z (2010) The performance of flat end and hemispherical end tools in single-point incremental forming. Int J Adv Manuf Technol 46(9–12):1113–1118Google Scholar
  70. 70.
    Lu B, Fang Y, Xu DK, Chen J, Ou H, Moser NH, Cao J (2014) Mechanism investigation of friction-related effects in single point incremental forming using a developed oblique roller-ball tool. Int J Mach Tools Manuf 85:14–29Google Scholar
  71. 71.
    Lu B, Ou H, Shi SQ, Long H, Chen J (2016) Titanium based cranial reconstruction using incremental sheet forming. Int J Mater Form 9(3):361–370Google Scholar
  72. 72.
    Henrard C, Bouffioux C, Eyckens P, Sol H, Duflou JR, Van Houtte P, Van Bael A, Duchene L, Habraken AM (2011) Forming forces in single point incremental forming: prediction by finite element simulations, validation and sensitivity. Comput Mech 47(5):573–590Google Scholar
  73. 73.
    Rauch M, Hascoët JY, Hamann JC, Plennel Y (2008) A new approach for toolpath programming in Incremental Sheet Forming. Int J Mater Form 1(1):1191–1194Google Scholar
  74. 74.
    Davarpanah MA, Mirkouei A, Yu X, Malhotra R, Pilla S (2015) Effects of incremental depth and tool rotation on failure modes and microstructural properties in Single Point Incremental Forming of polymers. J Mater Process Technol 222:287–300Google Scholar
  75. 75.
    Durante M, Formisano A, Langella A, Minutolo FMC (2009) The influence of tool rotation on an incremental forming process. J Mater Process Technol 209(9):4621–4626Google Scholar
  76. 76.
    Eyckens P, Duflou J, Van Bael A, Van Houtte P (2010) The significance of friction in the single point incremental forming process. Int J Mater Form 3(1):947–950Google Scholar
  77. 77.
    Oleksik V, Pascu A, Gavrus A, Oleksik M (2010) Experimental studies regarding the single point incremental forming process. Acad J Manuf Eng 8(2):51–56Google Scholar
  78. 78.
    Shrivastava P, Tandon P (2015) Investigation of the effect of grain size on forming forces in single point incremental sheet forming. Proc Manuf 2:41–45Google Scholar
  79. 79.
    Malhotra R, Cao J, Beltran M, Xu D, Magargee J, Kiridena V, Xia ZC (2012) Accumulative-DSIF strategy for enhancing process capabilities in incremental forming. CIRP Ann Manuf Technol 61(1):251–254Google Scholar
  80. 80.
    Fiorentino A (2013) Force-based failure criterion in incremental sheet forming. Int J Adv Manuf Technol 68(1–4):557–563Google Scholar
  81. 81.
    Fiorentino A, Ceretti E, Attanasio A, Mazzoni L, Giardini C (2009) Analysis of forces, accuracy and formability in positive die sheet incremental forming. Int J Mater Form 2(1):805Google Scholar
  82. 82.
    Lee BH, Keum YT, Wagoner RH (2002) Modeling of the friction caused by lubrication and surface roughness in sheet metal forming. J Mater Process Technol 130:60–63Google Scholar
  83. 83.
    Vahdati M, Mahdavinejad R, Amini S (2017) Investigation of the ultrasonic vibration effect in incremental sheet metal forming process. Proc Inst Mech Eng Part B J Eng Manuf 231(6):971–982Google Scholar
  84. 84.
    Dejardin S, Thibaud S, Gelin JC, Michel G (2010) Experimental investigations and numerical analysis for improving knowledge of incremental sheet forming process for sheet metal parts. J Mater Process Technol 210(2):363–369Google Scholar
  85. 85.
    Bambach M, Hirt G (2007) Error analysis in explicit finite element analysis of incremental sheet forming. AIP Conf Proc 908(1):859–864Google Scholar
  86. 86.
    Pohlak M, Küttner R, Majak J, Karjust K, Sutt A (2004) Simulation of incremental forming of sheet metal products. In: 4th international DAAAM conference, Estonia, pp 143–145Google Scholar
  87. 87.
    Eyckens P, Moreau JDL, Duflou JR, Van Bael A, Van Houtte P (2009) MK modelling of sheet formability in the incremental sheet forming process, taking into account through-thickness shear. Int J Mater Form 2(1):379Google Scholar
  88. 88.
    Micari F, Fratini L, Alberti N (1995) An explicit model for the thermal-mechanical analysis of hot metal forming processes. CIRP Ann 44(1):193–196Google Scholar

Copyright information

© The Brazilian Society of Mechanical Sciences and Engineering 2019

Authors and Affiliations

  • Ajay Kumar
    • 1
    • 2
    Email author
  • Vishal Gulati
    • 3
  • Parveen Kumar
    • 4
  • Hari Singh
    • 4
  1. 1.Department of Mechanical EngineeringK R Mangalam UniversityGurugramIndia
  2. 2.Faculty of Engineering and TechnologyShree Guru Gobind Singh Tricentenary UniversityGurugramIndia
  3. 3.Department of Mechanical EngineeringGuru Jambheshwar University of Science and TechnologyHisarIndia
  4. 4.Department of Mechanical EngineeringNational Institute of TechnologyKurukshetraIndia

Personalised recommendations