Skip to main content
Log in

Optimisation of drilling parameters on St37 based on Taguchi method

  • Technical Paper
  • Published:
Journal of the Brazilian Society of Mechanical Sciences and Engineering Aims and scope Submit manuscript

Abstract

Today, machining processes have become one of the most widely used methods in extensive production parts and drilling is one of the widely used machining processes in manufacturing. Almost 25% of the average time of machining process is for drilling. As a result, drilling during the production process is a bottleneck, and this is very evident in silos companies. Some difficulties associated with drilling in these companies are substantial problems, and they try to optimise their process. In this regard, the drilling process and its impact parameters are determined. By examining the factors and levels of machine and twist drill, the experimental design is done, and some factors such as spindle speed, feed rate, point angle, and clearance angle are taken into account. So, Taguchi method is performed and their results are analysed by signal-to-noise criterion, response surface method, and analysis of variances. According to some studies, two quantities of force and torque are considered as the output of the process simultaneously. Finally, by using signal-to-noise ratio (SNR) analysis, the optimum amounts of torque are determined for spindle speed, feed rate, point angle and clearance angle as is 320 rpm, 0.13 mm/min, 128° and 10°, respectively, and optimum amounts for force module are calculated as the previous values, while the point and clearance angles have been changed to 118° and 14°, respectively.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Kyratsis P, Bilalis N, Antoniadis A (2011) CAD-based simulations and design of experiments for determining thrust force in drilling operations. Comput Aided Des 43(12):1879–1890

    Article  Google Scholar 

  2. Mohan N, Ramachandra A, Kulkarni S (2005) Influence of process parameters on cutting force and torque during drilling of glass–fiber polyester reinforced composites. Compos Struct 71(3):407–413

    Article  Google Scholar 

  3. Singh AP, Sharma M (2013) Modelling of thrust force during drilling of fibre reinforced plastic composites. Procedia Eng 51:630–636

    Article  Google Scholar 

  4. Valarmathi T, Palanikumar K, Latha B (2013) Measurement and analysis of thrust force in drilling of particle board (PB) composite panels. Measurement 46(3):1220–1230

    Article  Google Scholar 

  5. Strenkowski J, Hsieh C, Shih A (2004) An analytical finite element technique for predicting thrust force and torque in drilling. Int J Mach Tools Manuf 44(12):1413–1421

    Article  Google Scholar 

  6. Tsao C, Hocheng H (2008) Evaluation of thrust force and surface roughness in drilling composite material using Taguchi analysis and neural network. J Mater Process Technol 203(1):342–348

    Article  Google Scholar 

  7. Kurt M, Bagci E, Kaynak Y (2009) Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes. Int J Adv Manuf Technol 40(5):458–469

    Article  Google Scholar 

  8. Tsao C, Chiu Y (2011) Evaluation of drilling parameters on thrust force in drilling carbon fiber reinforced plastic (CFRP) composite laminates using compound core-special drills. Int J Mach Tools Manuf 51(9):740–744

    Article  Google Scholar 

  9. Palanikumar K (2011) Experimental investigation and optimisation in drilling of GFRP composites. Measurement 44(10):2138–2148

    Article  Google Scholar 

  10. Kıvak T, Samtaş G, Cicek A (2012) Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills. Measurement 45(6):1547–1557

    Article  Google Scholar 

  11. Jalali S, Kolarik W (1991) Tool life and machinability models for drilling steels. Int J Mach Tools Manuf 31(3):273–282

    Article  Google Scholar 

  12. Paul A, Kapoor SG, DeVor RE (2005) Chisel edge and cutting lip shape optimization for improved twist drill point design. Int J Mach Tools Manuf 45(4):421–431

    Article  Google Scholar 

  13. Isbilir O, Ghassemieh E (2011) Finite element analysis of drilling of titanium alloy. Procedia Eng 10:1877–1882

    Article  Google Scholar 

  14. Prasanna J, Karunamoorthy L, Raman MV, Prashanth S, Chordia DR (2014) Optimization of process parameters of small hole dry drilling in Ti–6Al–4V using Taguchi and grey relational analysis. Measurement 48:346–354

    Article  Google Scholar 

  15. Neseli S (2014) Optimization of process parameters with minimum thrust force and torque in drilling operation using Taguchi method. Adv Mech Eng 6:925382

    Article  Google Scholar 

  16. Chaudhary G, Kumar M, Verma S, Srivastav A (2014) Optimization of drilling parameters of hybrid metal matrix composites using response surface methodology. Procedia Mater Sci 6:229–237

    Article  Google Scholar 

  17. Chatterjee S, Abhishek K, Mahapatra SS, Datta S, Yadav RK (2014) NSGA-II approach of optimization to study the effects of drilling parameters in AISI-304 stainless steel. Procedia Eng 97:78–84

    Article  Google Scholar 

  18. Çiçek A, Kıvak T, Ekici E (2015) Optimization of drilling parameters using Taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically treated HSS drills. J Intell Manuf 26(2):295–305

    Article  Google Scholar 

  19. Santhanakrishnan M, Sivasakthivel PS, Sudhakaran R (2017) Modeling of geometrical and machining parameters on temperature rise while machining Al 6351 using response surface methodology and genetic algorithm. J Braz Soc Mech Sci Eng 39(2):487–496

    Article  Google Scholar 

  20. Goharimanesh M, Akbari A (2015) Optimum parameters of nonlinear integrator using design of experiments based on Taguchi method. J Appl Mech 46(2):233–241

    Google Scholar 

  21. Goharimanesh M, Akbari A, Tootoonchi AA (2014) More efficiency in fuel consumption using gearbox optimization based on Taguchi method. J Ind Eng Int 10(2):1–8

    Article  Google Scholar 

  22. Dikshit MK, Puri AB, Maity A (2017) Modelling and application of response surface optimization to optimize cutting parameters for minimizing cutting forces and surface roughness in high-speed, ball-end milling of Al2014-T6. J Braz Soc Mech Sci Eng 39(12):5117–5133

    Article  Google Scholar 

  23. Stalin John MR, Banerjee N, Shrivastava K, Vinayagam BK (2017) Optimization of roller burnishing process on EN-9 grade alloy steel using response surface methodology. J Braz Soc Mech Sci Eng 39(8):3089–3101

    Article  Google Scholar 

  24. Taguchi G (1986) Introduction to quality engineering: designing quality into products and processes. The Organization, Tokyo

    Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Aliakbar Akbari.

Additional information

Technical Editor: Márcio Bacci da Silva.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Samavi, J., Goharimanesh, M., Akbari, A. et al. Optimisation of drilling parameters on St37 based on Taguchi method. J Braz. Soc. Mech. Sci. Eng. 40, 370 (2018). https://doi.org/10.1007/s40430-018-1245-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s40430-018-1245-y

Keywords

Navigation