Machining performance optimization during plasma arc cutting of AISI D2 steel: application of FIS, nonlinear regression and JAYA optimization algorithm

  • Parthkumar Patel
  • Bhavdeep Nakum
  • Kumar Abhishek
  • V. Rakesh Kumar
Technical Paper
  • 41 Downloads

Abstract

The work focuses on assessing the optimal machining conditions which could simultaneously satisfy multiple process performance indices during machining of AISI D2 steel. The main characteristic indices that have been considered here for evaluating plasma arc machining are surface roughness and material removal rate; the corresponding machining parameters are cutting speed, gas pressure and torch height. The study proposes an integrated optimization module combining fuzzy inference system, nonlinear regression and JAYA algorithm towards optimizing correlated multi-response features during machining of AISI D2 steel. Optimum value of machining parameters found as cutting speed of 4000 m/min, gas pressure of 95 psi and torch height of 0.5 mm using aforementioned methodology. Application potential of the aforesaid integrated optimization route has been compared to that of teaching–learning based optimization (TLBO) algorithm and genetic algorithm. It has been concluded that JAYA algorithm possesses less convergence time and hence execution is faster as compared to TLBO and genetic algorithm.

Keywords

AISI D2 steel Fuzzy inference system Nonlinear regression JAYA algorithm Teaching–learning based optimization (TLBO) algorithm Genetic algorithm 

References

  1. 1.
    Abhishek K, Datta S, Mahapatra SS (2016) Multi-objective optimization in drilling of CFRP (polyester) composites: application of a fuzzy embedded harmony search (HS) algorithm. Measurement 77:222–239CrossRefGoogle Scholar
  2. 2.
    Abhishek K, Kumar VR, Datta S, Mahapatra SS (2015) Parametric appraisal and optimization in machining of CFRP composites by using TLBO (teaching–learning based optimization algorithm). J Intell Manuf 28:1–17Google Scholar
  3. 3.
    Adalarasan R, Santhanakumar M, Rajmohan M (2015) Application of Grey Taguchi-based response surface methodology (GT-RSM) for optimizing the plasma arc cutting parameters of 304L stainless steel. Int J Adv Manuf Technol 78:1161–1170CrossRefGoogle Scholar
  4. 4.
    Ali S, Prasad DK, Shankar S, Saw K (2016) Experimental investigation of temperature distribution and surface roughness for cutting aluminium-19000 and stainless steel 304 using plasma arc cutting. Int J Adv Technol Eng Sci 4:153–158Google Scholar
  5. 5.
    Bhuvenesh R, Saifuldin M, Norizaman MH (2012) Surface roughness and MRR effect on manual plasma arc cutting machining. World Acad Sci Eng Technol 6:465–468Google Scholar
  6. 6.
    Bini R, Colosimo BM, Kutlu AE, Monno M (2008) Experimental study of the features of the kerf generated by a 200A high tolerance plasma arc cutting system. J Mater Process Technol 196(1):345–355CrossRefGoogle Scholar
  7. 7.
    Chamarthi S, Sinivasa Reddy N, Elipey MK, Ramana Reddy DV (2013) Investigation analysis of plasma arc cutting parameters on the unevenness surface of hardox-400 material. Procedia Eng 64:854–861CrossRefGoogle Scholar
  8. 8.
    Cox E (1992) Fuzzy fundamentals. IEEE Spectr 29(10):58–61CrossRefGoogle Scholar
  9. 9.
    Gariboldi E, Previtali B (2005) High tolerance plasma arc cutting of commercially pure titanium. J Mater Process Technol 160(1):77–89CrossRefGoogle Scholar
  10. 10.
    Harničárová M, Valíček J, Čep R, Tozan H, Müllerová J, Grznárik R (2013) Comparison of non-traditional technologies for material cutting from the point of view of surface roughness. Int J Adv Manuf Technol 69(1–4):81–91CrossRefGoogle Scholar
  11. 11.
    Ilii SM, Coteata M, Munteanu A (2010) Experimental results concerning the variation of surface roughness parameter (Ra) at plasma arc cutting of a stainless steel workpiece. Int J Mod Manuf Technol II(1):31–36Google Scholar
  12. 12.
    Iosub A, Nagit G, Negoescu F (2008) Plasma cutting of composite materials. Int J Mater Form 1(1):1347–1350CrossRefGoogle Scholar
  13. 13.
    Klimpel A, Cholewa W, Bannister A, Luksa K, Przystałka P, Rogala T, Skupnik D, Cicero S, Martín-Meizoso A (2017) Experimental investigations of the influence of laser beam and plasma arc cutting parameters on edge quality of high-strength low-alloy (HSLA) strips and plates. Int J Adv Manuf Technol 92:1–15CrossRefGoogle Scholar
  14. 14.
    Mamdani EH (1976) Advances in the linguistic synthesis of fuzzy controllers. Int J Man Mach Stud 8(6):669–678CrossRefMATHGoogle Scholar
  15. 15.
    Pawar PJ, Rao RV (2013) Parameter optimization of machining processes using teaching–learning based optimization algorithm. Int J Adv Manufact Technol 67(5):995–1006CrossRefGoogle Scholar
  16. 16.
    Rao R (2016) Jaya: a simple and new optimization algorithm for solving constrained and unconstrained optimization problems. Int J Ind Eng Comput 7(1):19–34MathSciNetGoogle Scholar
  17. 17.
    Rao RV, Kalyankar VD (2013) Multi-pass turning process parameter optimization using teaching–learning-based optimization algorithm. Sci Iran 20(3):967–974Google Scholar
  18. 18.
    Rao RV, Kalyankar VD (2013) Parameter optimization of modern machining processes using teaching–learning-based optimization algorithm. Eng Appl Artif Intell 26(1):524–531CrossRefGoogle Scholar
  19. 19.
    Rao RV, More KC, Taler J, Ocłoń P (2016) Dimensional optimization of a micro-channel heat sink using Jaya algorithm. Appl Therm Eng 103:572–582CrossRefGoogle Scholar
  20. 20.
    Schnick M, Fussel M, Zscetzsche J (2006) Simulation of plasma and shielding gas flows in welding and cutting arcs with ansys CFX. Int Sci Colloq Model Mater Process 1:143–148Google Scholar
  21. 21.
    Singh V (2012) Analysis of process parameters of plasma arc cutting using design of experiment. Doctoral dissertationGoogle Scholar
  22. 22.
    Tsiolikas A, Kechagias J, Salonitis K, Mastorakis N (2016) Optimization of cut surface quality during CNC Plasma Arc Cutting process. Int J Syst Appl Eng Dev 10:305–308Google Scholar
  23. 23.
    Verma RK, Abhishek K, Datta S, Mahapatra SS (2011) Fuzzy rule based optimization in machining of FRP composites. Turk J Fuzzy Syst 2(2):99–121Google Scholar
  24. 24.
    Xu WJ, Fang JC, Lu YS (2002) Study on ceramic cutting by plasma arc. J Mater Process Technol 129(1):152–156CrossRefGoogle Scholar
  25. 25.
    Yamaguchi Y, Katada Y, Itou T, Uesugi Y, Tanaka Y, Ishijima T (2015) Experimental investigation of magnetic arc blow in plasma arc cutting. Weld World 59(1):45–51CrossRefGoogle Scholar
  26. 26.
    Zadeh LA (1965) Fuzzy sets. Inf Control 8(3):338–353CrossRefMATHGoogle Scholar
  27. 27.
    Zhou B, Liu YJ, Tan SK (2013) Efficient simulation of oxygen cutting using a composite heat source model. Int J Heat Mass Transf 57(1):304–311CrossRefGoogle Scholar

Copyright information

© The Brazilian Society of Mechanical Sciences and Engineering 2018

Authors and Affiliations

  1. 1.Department of Mechanical EngineeringInstitute of Infrastructure, Technology, Research and Management (IITRAM)AhmedabadIndia
  2. 2.Department of Mechanical EngineeringNational Institute of TechnologyRourkelaIndia

Personalised recommendations