Advertisement

Forces and coefficient of friction during cylindrical three roller bending

  • Shakil A. Kagzi
  • H. K. Raval
Technical Paper

Abstract

Three roller bending process is one of the processes of forming cylindrical shells, for manufacturing drums, pressure vessels, windmill towers, etc. During the bending process, forces on the rollers must not exceed their bending capacity. Along with operational and material parameters, the forces exerted during bending and power consumption are affected by the coefficient of friction at the roller-plate interface. It is difficult to determine the coefficient of friction practically during three roller bending process. An attempt is made to determine the forces and friction coefficient at each roller–plate interface, through derived mathematical model, using experimental results. The variation of coefficient of friction under the higher loading conditions was also determined as a case study. With the present mathematical formulation along with the coefficient of friction, the forces at each roller–plate interface could be determined more precisely. The determination of forces and friction coefficient helps in deciding operational and design parameters of the bending machine, respectively.

Keywords

Three roller bending Coefficient of friction Bending forces Bending power Cylindrical bending Rolling friction Friction 

Nomenclatures

a

Distance between the axis of two bottom rollers

ae, ax

Perpendicular distance of the vertical forces on the bottom roller at the entry and the exit side, respectively, from the top roller contact point

Ftangential

Tangential force acting at the interface of the two bodies

Fnormal

Normal force acting at the point of contact of the two bodies

Ht, He, Hx

Horizontal force on the top roller the bottom roller at the entry and the bottom roller on the exit side, respectively

It, Ib

Moment of inertia on the top roller and the bottom rollers, respectively

J

Normal force at the contact between the plate and the bottom roller at the entry side

K

Strength coefficient

Me, Mx

Bending moment of the resultant force at the bottom roller on the entry and the exit side, respectively, about the top roller contact point

Mexternal

External bending moment based on applied forces

Minternal

Internal bending moment based on the geometry of material its properties

Nt, Nb

Revolution per minute of the top roller and bottom rollers, respectively

n

Strain hardening exponent

P

Normal force at the top roller contact point

pt, pe, px

Power consumed during bending at the top roller the bottom roller at the entry and the bottom roller on the exit side, respectively

pe-shaft, px-shaft

Power consumed in rotating just the shaft of the bottom roller at the entry and the bottom roller on the exit side, respectively

ppl

Power consumed only in bending and driving plate across the rollers. It does not include the power consumed by motors and shaft of the rollers

pn(av)

Average of pe-shaft and px-shaft Q Normal force at the contact between the plate and the bottom roller at the exit side

RP, RJ, RQ

Resultant force at the top roller the bottom roller at the entry and the bottom roller on the exit side, respectively

R

Radius of the circle tangent all the three rollers

rt, rb

Radius of the top roller and the bottom rollers, respectively

t

Thickness of the plate

U

Displacement of the top roller

ue, ux

Perpendicular distance of the horizontal forces at the bottom roller at the entry and the exit side, respectively, from the top roller contact point

Vt, Ve, Vx

Vertical force on the top roller the bottom roller at the entry and the bottom roller on the exit side, respectively

W

The weight of the plate

xe, xx

The horizontal distance of the contact points of the bottom roller at the entry and the exit side, respectively, from the reference point

ye, yx

The vertical distance of the contact points of the bottom roller at the entry and the exit side, respectively, from the reference point

Λ

Angular acceleration of the top and the bottom rollers

μ

Friction coefficient (CF)

μt, μe, μx

CF at the roller-plate interface for the top roller, the bottom roller at the entry and the bottom roller on the exit side, respectively

θt, θe, θx

Contact angle at the top roller, the bottom roller at the entry, and the bottom roller on the exit side, respectively

Notes

Funding

The present work is a part of project sponsored by the Department of Science and Technology (DST), under Scientific and Engineering Research Council (SERC)-engineering science scheme, Ministry of Technology, Government of India (Grant sanction number: SR/S3/MERC-0047/2011 dated:16/04/2012).

References

  1. 1.
    Yang Ming, Shima Susumu (1988) Simulation of bending type three roller bending process. Int J Mech Sci 30(12):877–886CrossRefGoogle Scholar
  2. 2.
    Raval HK (2002) Experimental and theoretical investigation of bending process (Vee and three roller bending). Ph. D. Thesis. Surat (India), South Gujarat UniversityGoogle Scholar
  3. 3.
    Gandhi AH, Raval HK (2008) Analytical and empirical modeling of top roller position for three roller cylindrical bending of plates and its experimental verification. J Mater Process Technol 197(1):268–278CrossRefGoogle Scholar
  4. 4.
    Chudasama MK, Raval HK (2013) An approximate bending force prediction for three roller conical bending process. Int J Mater Form 6(2):303–314CrossRefGoogle Scholar
  5. 5.
    Chudasama MK, Raval HK (2014) Bending force prediction for dynamic roll-bending during 3-roller conical bending process. J Manuf Processes 16(2):184–295CrossRefGoogle Scholar
  6. 6.
    Zhengkun Feng, Henri Chamliaud (2011) Three stage process for improving roll bending quality. Simul Model Pract Theory 19(2):887–898CrossRefGoogle Scholar
  7. 7.
    Zhengkun Feng, Henri Chamliaud (2011) Modeling and simulation of asymmetrical three-roll bending process. Simul Model Pract Theory 19(9):1913–1917CrossRefGoogle Scholar
  8. 8.
    Kagzi SA, Raval HK (2015) An analysis of forces during three roller bending process. Int J Mater Prod Technol 51(3):248–263CrossRefGoogle Scholar
  9. 9.
    Kagzi SA, Raval HK (2016) Parametric study on roller forming process. Adv Mater Process Technol 1(3/4):586–598Google Scholar
  10. 10.
    IS2062 (2006) Hot rolled medium and high tensile structural steels. Bureau of Indian Standards, New DelhiGoogle Scholar
  11. 11.
    IS1608 (1995) Mechanical testing of metals—tensile testing. Bureau of Indian Standards, New DelhiGoogle Scholar
  12. 12.
    Marciniak Z, Duncan JL (1992) The mechanics of sheet metal forming. Edward Arnold, LondonGoogle Scholar
  13. 13.
    Martin G, Tsang S (1996) The plastic bending of beams considering die friction effects. J Eng Ind 88:237–250CrossRefGoogle Scholar
  14. 14.
    Bhushan Bharat (2013) Introduction to tribology. Wiley, New YorkCrossRefGoogle Scholar

Copyright information

© The Brazilian Society of Mechanical Sciences and Engineering 2018

Authors and Affiliations

  1. 1.Sardar Vallabhbhai National Institute of TechnologySuratIndia

Personalised recommendations