Skip to main content
SpringerLink
Log in

Comparison of CMT with other arc modes for laser-arc hybrid welding of steel

  • Research Paper
  • Published:
Welding in the World Aims and scope Submit manuscript

Abstract

In this study, three different arc modes in laser-arc hybrid welding with a gas metal arc were studied, i.e. the standard, pulsed and cold metal transfer (CMT) modes. The pulsed mode is more controlled than the standard mode and offers reduced heat input to the workpiece, which enables welding of thinner materials. The CMT mode utilizes surface tension drop transfer with controlled wire feeding, and therefore, involves less heat input than the other arc modes, and it is also considered to generate less undercut and spatter than the other modes. This study compares hybrid welds made by the three arc modes with a close-to-production setup for low and medium wire deposition rates, within the limits of the CMT process. The welds were studied by scanning and high speed imaging. The study shows that the differences between the drop transfer modes are reduced due to the presence of a laser keyhole. The dominating influence on the solidification and melt flow is the arc and especially the gouge created ahead of the keyhole. The main pros and cons of the different arc modes are discussed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11

Similar content being viewed by others

References

  1. Karlsson J, Norman P, Kaplan AFH, Rubin P, Lamas J, Yañez A (2011) Observation of the mechanisms causing two kinds of undercut during laser hybrid arc welding. Appl Surf Sci 257:7501–7506

    Google Scholar 

  2. Engström H, Nilsson K, Flinkfeldt J, Skirfors A, Gustavsson B (2001) Laser Hybrid Welding of High Strength Steels, 20th ICALEO Conference. Jacksonville, FL, USA

  3. Powell J, Lamas J, Karlsson J, Norman P, Kaplan AFH (2011) The sensitivity of hybrid laser welding to variations in workpiece position, LIM Conference. Munich, Germany

  4. Kaplan AFH, Lamas J, Karlsson J, Norman P, Yañez A (2011) Scanner analysis of the topology of laser hybrid welds depending on the joint edge tolerances, 12th NOLAMP Conference. Trondheim, Norway

  5. Scotti A, Ponomarev V, Lucas W (2012) A scientific application oriented classification for metal transfer modes in GMA welding. J Mater Process Technol 212:1406–1413

    Article  Google Scholar 

  6. Campana G, Fortunato A, Ascari A, Tani G, Tomesani L (2007) The influence of arc transfer mode in hybrid laser-mig welding. J Mater Process Technol 191:111–113

    Article  Google Scholar 

  7. Pickin CG, Young K (2006) Evaluation of cold metal transfer (CMT) process for welding aluminium alloy. Sci Technol Weld Join 11:583–585

    Article  Google Scholar 

  8. Zhang C, Gao M, Zeng X (2012) A comprehensive study of laser, CMT, laser-pulse MIG hybrid and laser-CMT hybrid welded aluminium alloy, 31st ICALEO conference. Aneheim, California, USA

  9. Michalec I, Barta J, Jancar J, Bartova K, Maronek M (2011) Metallurgical joining of steel sheets treated by nitrooxidation by a hybrid CMT-laser process, Proceedings 20th Conference on Metallurgy and Materials. Brno, CZ, Ostrava

  10. Li G, Gao M, Zhang C, Zeng X (2012) Laser-arc hybrid welding of thick-section mild steel plates: Microstructure and performances of the beads, 31st ICALEO conference. Anaheim, California, USA

  11. Alam MM, Barsoum Z, Jonsén P, Kaplan AFH, Häggblad HÅ (2010) The influence of surface geometry and topography on the fatigue cracking behaviour of laser hybrid welded eccentric fillet joints. Appl Surf Sci 256:1936–1945

    Google Scholar 

  12. Ribic B, Palmer TA, DebRoy T (2009) Problems and issues in laser-arc hybrid welding. Int Mater Rev 54:223–244

    Article  Google Scholar 

  13. Cho JH, Na SJ (2009) Three-dimensional analysis of molten pool in GMA-Laser hybrid welding. Weld J 88:35–43

    Google Scholar 

  14. Moradi M, Ghoreishi M, Frostevarg J, Kaplan AFH (2013) An investigation on stability of laser hybrid arc welding. Opt Lasers Eng 51:481–487

    Article  Google Scholar 

  15. Lamas J, Karlsson J, Powell J, Kaplan AFH, Yañez A (2013) The effect of fit-up geometry on melt flow and weld quality in laser hybrid welding. J Laser Appl 25:7

    Article  Google Scholar 

  16. Fellman A, Salminen A, (2006) Observation of the phenomena of CO2 laser-MAG hybrid welding, ICALEO. LIA

  17. Eriksson I, Gren P, Powell J, Kaplan AFH (2010) New high-speed photography technique for observation of fluid flow in laser welding, Optical Engineering. 49

  18. Kim Y, Alam N, Bang H, Bang H (2006) Observation of hybrid (cw Nd:YAG laser + MIG) welding phenomenon in AA 5083 butt joints with different gap condition. Sci Technol Weld Join 11:295–307

    Article  Google Scholar 

  19. Mendez PF, Eagar TW (2003) Penetration and defect formation in high current arc welding. Weld J 82:296–306

    Google Scholar 

  20. Zhou J, Tsai HL (2008) Modeling of transport phenomena in hybrid laser-MIG keyhole welding. Int J Heat Mass Transf 51:4353–4366

    Article  Google Scholar 

  21. Schierl A (2005) The CMT process a revolution in welding technology. Weld World 49:38

    Google Scholar 

  22. Karlsson J, Kaplan AFH (2012) Comprehensive monitoring and control of laser hybrid arc welding in industrial production, 31st ICALEO Conference. Anaheim, California, USA

  23. Nguyen TC, Weckman DC, Johnson DA, Kerr HW (2006) High speed fusion weld bead defects. Sci Technol Weld Join 11:618–633

    Article  Google Scholar 

Download references

Acknowledgements

The authors gratefully acknowledge funding by the European Commission, programme FP7-RFCS, project HYBRO, no. RFS-CR-12024 and by VINNOVA—The Swedish Agency for Innovation Systems, programme FFI, project ROBUHYB, no. 2011–01782.

Author information

Authors and Affiliations

  1. Luleå Tekniska Universitet, Luleå, 97187, Sweden

    Jan Frostevarg, Alexander F. H. Kaplan & Javier Lamas

Authors
  1. Jan Frostevarg
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Alexander F. H. Kaplan
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Javier Lamas
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Jan Frostevarg.

Additional information

Doc. IIW-2461, recommended for publication by Commission IV “Power Beam Processes”.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Frostevarg, J., Kaplan, A.F.H. & Lamas, J. Comparison of CMT with other arc modes for laser-arc hybrid welding of steel. Weld World 58, 649–660 (2014). https://doi.org/10.1007/s40194-014-0146-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40194-014-0146-7

Keywords

Search

Navigation